Each DPLL exists in its own powerdomain (cf 34xx TRM figure 4-18) and
clockdomain; so, create powerdomain and clockdomain structures for them.
Mark each DPLL clock as belonging to their respective DPLL clockdomain.
cf. 34xx TRM Table 4-27 (among other references).

linux-omap source commits are acdb615850b9b4f7d1ab68133a16be8c8c0e7419 and
a8798a48f33e9268dcc7f30a4b4a3ce4220fe0c9.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

sys_clkout2 belongs in the core_clkdm (3430 TRM section 4.7.2.2).
It's not clear whether it actually is in the CORE clockdomain, or whether
it is technically in a different clockdomain; but this is closer to
reality than the present configuration.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Filling the set_rate and round_rate fields of dpll4_m4_ck makes
this clock programmable through clk_set_rate().  This is needed
to give omapfb control over the dss1_alwon_fck rate.

This patch includes a fix from Tomi Valkeinen <tomi.valkeinen@nokia.com>.

linux-omap source commits are e42218d45afbc3e654e289e021e6b80c657b16c2 and
9d211b761b3cdf7736602ecf7e68f8a298c13278.
Signed-off-by: NMåns Rullgård <mans@mansr.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add CSI2 clock struct for handling it with clock API when TI PM is disabled.

linux-omap source commit is 8b20f4498928459276bd3366e3381ad595d23432.
Signed-off-by: NSergio Aguirre <saaguirre@ti.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The GFX/SGX functional and interface clocks have different masks, for
some unknown reason, so split EN_SGX_SHIFT into one each for fclk and
iclk.

Correct according to the TRM and the far more important 'does this
actually work at all?' metric.

linux-omap source commit is de1121fdb899f762b9e717f44eaf3fae7c00cd3e.
Signed-off-by: NDaniel Stone <daniel.stone@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix some bugs in the OMAP3 clock tree pertaining to the 96MHz clocks.
The 96MHz portion of the clock tree should now have reasonable
fidelity to the 34xx TRM Rev I.

One remaining question mark: it's not clear exactly which 96MHz source
clock the USIM uses.  This patch sticks with the previous setting, which
seems reasonable.

linux-omap source commit is 15c706e8179ce238c3ba70a25846a36b73bd2359.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove usbhost_sar_fclk from the OMAP3 clock framework.  The bit that
the clock was tweaking doesn't actually enable or disable a clock; it
controls whether the hardware will save and restore USBHOST state
when the powerdomain changes state.  (That happens to coincidentally
enable a clock for the duration of the operation, hence the earlier
confusion.)

In place of the clock, mark the USBHOST powerdomain as supporting
hardware save-and-restore functionality.

linux-omap source commit is f3ceac86a9d425d101d606d87a5af44afef27179.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add non-CORE DPLL rate set code and M,N programming for OMAP3.
Connect it to OMAP34xx DPLLs 1, 2, 4, 5 via the clock framework.

You may see some warnings on rate sets from the freqsel code.  The
table that TI presented in the 3430 TRM Rev F does not cover Fint <
750000, which definitely occurs in practice.  However, the lack of this
freqsel case does not appear to impair the DPLL rate change.

linux-omap source commit is 689fe67c6d1ad8f52f7f7b139a3274b79bf3e784.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

propagate_rate() is recursive, so it makes sense to minimise the
amount of stack which is used for each recursion.  So, rather than
recursing back into it from the ->recalc functions if RATE_PROPAGATES
is set, do that test at the higher level.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The original code in omap2_clk_wait_ready() used to check the low 8
bits to determine whether they were within the FCLKEN or ICLKEN
registers.  Specifically, the test is satisfied when these offsets
are used:

 CM_FCLKEN, CM_FCLKEN1, CM_CLKEN, OMAP24XX_CM_FCLKEN2, CM_ICLKEN,
 CM_ICLKEN1, CM_ICLKEN2, CM_ICLKEN3, OMAP24XX_CM_ICLKEN4
 OMAP3430_CM_CLKEN_PLL, OMAP3430ES2_CM_CLKEN2

If one of these offsets isn't used, omap2_clk_wait_ready() merely
returns without doing anything.  So we should use the non-wait clkops
version instead and eliminate that conditional.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rather than employing run-time tests in omap2_clk_wait_ready() to
decide whether we need to wait for the clock to become ready, we
can set the .ops appropriately.

This change deals with the OMAP24xx and OMAP34xx conditionals only.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

PARENT_CONTROLS_CLOCK just makes enable/disable no-op, and is
functionally an alias for ALWAYS_ENABLED.  This can be handled
in the same way, using clkops_null.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

... and use it for clocks which are ALWAYS_ENABLED.  These clocks
use a non-NULL enable_reg pointer for other purposes (such as
selecting clock rates.)
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Collect up all the common enable/disable clock operation functions
into a separate operations structure.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This will simplify the MMC low-level init, and make it more
flexible to add support for a newer MMC controller in the
following patches.

The patch rearranges platform data and gets rid of slot vs
controller confusion in the old data structures. Also fix
device id numbering in the clock code.

Some code snippets are based on an earlier patch by
Russell King <linux@arm.linux.org.uk>.

Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch changes gpio "driver" to enable debounce clock for
gpio-bank only when debounce is enabled for some gpio in that bank.

Gpio functional clocks are also renamed in clock tree, gpioX_fck ->
gpioX_dbck.

This patch triggers problem with gpio wake-up and Omap3. Gpios in PER
domain aren't capable to generate wake-up if PER domain is in sleep
state. For this iopad wake-up should be used and needed pad
configuration should be done. Enabling iopad wake-up for gpio pads is
left for bootloader or omap mux configuration in kernel.
Signed-off-by: NJouni Hogander <jouni.hogander@nokia.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

E.g dss_l3_ick and dss_l4_ick have same gating control. Having own
clock for both of them causes race condition between enable / disable.

This patch combines this kind of clocks and names new clock as <module>_ick.
Signed-off-by: NJouni Hogander <jouni.hogander@nokia.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch integrates the OMAP3 clock tree with the clockdomain code.
This patch:

- marks OMAP34xx clocks with their corresponding clockdomain.

- adds code to convert the clockdomain name to a clockdomain pointer in the
  struct clk during clk_register().

- modifies OMAP2 clock usecounting to call into the clockdomain code
  when clocks are enabled or disabled.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds a new rate rounding algorithm for DPLL clocks on the
OMAP2/3 architecture.

For a desired DPLL target rate, there may be several
multiplier/divider (M, N) values which will generate a sufficiently
close rate.  Lower N values result in greater power economy.  However,
lower N values can cause the difference between the rounded rate and
the target rate ("rate error") to be larger than it would be with a
higher N.  This can cause downstream devices to run more slowly than
they otherwise would.

This DPLL rate rounding algorithm:

- attempts to find the lowest possible N (DPLL divider) to reach the
  target_rate (since, according to Richard Woodruff <r-woodruff@ti.com>,
  lower N values save more power than higher N values).

- allows developers to set an upper bound on the error between the
  rounded rate and the desired target rate ("rate tolerance"), so an
  appropriate balance between rate fidelity and power savings can be
  set.  This maximum rate error tolerance is set via
  omap2_set_dpll_rate_tolerance().

- never returns a rounded rate higher than the target rate.

The rate rounding algorithm caches the last rounded M, N, and rate
computation to avoid rounding the rate twice for each clk_set_rate()
call.  (This patch does not yet implement set_rate for DPLLs; that
follows in a future patch.)

The algorithm trades execution speed for rate accuracy.  It will find
the (M, N) set that results in the least rate error, within a
specified rate tolerance.  It does this by evaluating each divider
setting - on OMAP3, this involves 128 steps.  Another approach to DPLL
rate rounding would be to bail out as soon as a valid rate is found
within the rate tolerance, which would trade rate accuracy for
execution speed.  Alternate implementations welcome.

This code is not yet used by the OMAP24XX DPLL clock, since it
is currently defined as a composite clock, fusing the DPLL M,N and the
M2 output divider.  This patch also renames the existing OMAP24xx DPLL
programming functions to highlight that they program both the DPLL and
the DPLL's output multiplier.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds support for DPLL autoidle control to the OMAP3 clock
framework.  These functions will be used by the noncore DPLL enable
and disable code - this is because, according to the CDP code, the
DPLL autoidle status must be saved and restored across DPLL
lock/bypass/off transitions.

N.B.: the CORE DPLL (DPLL3) has three autoidle mode options, rather
than just two.  This code currently does not support the third option,
low-power bypass autoidle.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds support for mach-omap2 based on current
mcbsp platform driver.
Signed-off-by: NEduardo Valentin <eduardo.valentin@indt.org.br>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch removes following message on dpll5_m2_ck enable and
disable:

clock.c: Enable for dpll5_m2_ck without enable code
clock: clk_disable called on independent clock dpll5_m2_ck
which has no enable_reg
Signed-off-by: NJouni Hogander <jouni.hogander@nokia.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

ssi_l4_ick should have PARENT_CONTROLS_CLOCK flag.
ST_SSI_STDBY bit in idlest register cannot be used in  omap2_clk_wait_ready
Signed-off-by: NJouni Högander <jouni.hogander@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add fuctional clock enabler for iva2
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Wrong shift values were used for gpio2-6  fclks (gpt2-6 shift).
Signed-off-by: NJouni Högander <jouni.hogander@nokia.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

These changes is the result of the discussion with Paul Walmsley.
His ideas are included into this patch.

Remove DPLL output divider handling from DPLLs and CLKOUTX2 clocks,
and place it into specific DPLL output divider clocks (e.g., dpll3_m2_clk).
omap2_get_dpll_rate() now returns the correct DPLL rate, as represented
by the DPLL's CLKOUT output. Also add MPU and IVA2 subsystem clocks, along
with high-frequency bypass support.

Add support for DPLLs function in locked and bypass clock modes.
Signed-off-by: NRoman Tereshonkov <roman.tereshonkov@nokia.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch defines 34xx clocks.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>