Convert the normal transmit completion path from dev_kfree_skb_any()
to dev_consume_skb_any() to help keep dropped packet profiling
meaningful.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTNL should be already held in the notifier call so the slave list can
be traversed without a problem, remove the unnecessary bond->lock.

CC: Hariprasad S <hariprasad@chelsio.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch defines a platform glue layer for Rockchip SoCs which
support arc-emac driver. It ensures that regulator for the rmii is on
before trying to connect to the ethernet controller. It applies right
speed and mode changes to the grf when ethernet settings change.
Signed-off-by: NRomain Perier <romain.perier@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It removes the owner field updation of driver structure.
It will be automatically updated by module_platform_driver()
Signed-off-by: NVarka Bhadram <varkab@cdac.in>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CPSW supports both rx and tx pause frames for flow control.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A bit of floor sweeping in a dusty old corner.  Convert the "normal"
skb free calls to dev_consume_skb_any() so packet drop tracing will
be more sane.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Acked-by: NJaroslav Kysela <perex@perex.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change e1000_set_eee and e1000_set_eee_i35(0|4) to allow
changes in the advertised EEE speeds from ethtool. Adds two boolean
flags to e1000_set_eee_i35(0|4) to pass in advertised speed data.
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixed many errors/warnings and checks in e1000_ethtool.c reported
by checkpatch.pl.  Suggestions from Joe Perches and Alexander Duyck
applied as well
Signed-off-by: NKrzysztof Majzerowicz-Jaszcz <cristos@vipserv.org>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As the management counters reach a threshold they will generate an
interrupt so the value can be saved and the counter reset. The
current code does not enable this interrupt on all counters. This
can result in inaccurate statistics.

Update the code to enable all the counters to generate an interrupt
when its threshold is exceeded.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Even if the management counters are configured to be 32 bit register
values, the [rt]xoctetcount_gb and [rt]xoctetcount_g counters are
always 64 bit counter registers.  Since they are not being treated as
64 bit values, these statistics are being reported incorrectly (ifconfig,
ethtool, etc.).

Update the routines used to read the registers to access the "hi"
register (an offset of 4 from the "lo" register) to create a 64 bit
value for these 64 bit counters.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the new fancy eth_get_headlen() to pull exactly the headers
into skb->head.

This speeds up GRE traffic (or more generally tunneled traffuc),
as GRO can aggregate up to 17 MSS per GRO packet instead of 8.

(Pulling too much data was forcing GRO to keep 2 frags per MSS)
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch does not affect the 10/100 GRETH MAC.

Before all GBit GRETH TX descriptor ring cleaning was done in
start_xmit(), when descriptor list became full it activated
TX interrupt to start the NAPI rx poll function to do TX ring
cleaning.

With this patch the TX descriptor ring is always cleaned from
the NAPI rx poll function, triggered via TX or RX interrupt.
Otherwise we could end up in TX frames being sent but not
reported to the stack being sent. On the 10/100 GRETH this
is not an issue since the SKB is copied&aligned into private
buffers so that the SKB can be freed directly on start_xmit()
Signed-off-by: NDaniel Hellstrom <daniel@gaisler.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cnic module needs to ensure that if ipv6 support is compiled as a module,
then the cnic module cannot be compiled as built-in as it depends on ipv6.
Made this check cleaner via Kconfig

Use simpler IS_ENABLED for CONFIG_VLAN_8021Q check
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update ixgbe to drop the ixgbe_get_headlen function in favor of eth_get_headlen.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update igb to drop the igb_get_headlen function in favor of eth_get_headlen.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When 1G SFP RJ45 module is detected, driver must reset the Tx laser
in order to prevent link issues. As part of change, the link_attr_sync
was relocated from vars to params.
Signed-off-by: NYaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This bug was reported on a very old kernel (RHEL6, 2.6.32-491.el6):

BUG: unable to handle kernel paging request at 00800000
IP: [<c04107b5>] nommu_map_page+0x15/0x110
*pdpt = 000000003454f001 *pde = 000000003f03d067
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/system/cpu/online
Modules linked in: nfsd lockd nfs_acl auth_rpcgss sunrpc exportfs p4_clockmod
ipv6 ppdev parport_pc parport microcode iTCO_wdt iTCO_vendor_support 3c59x mii
dcdbas serio_raw snd_intel8x0 snd_ac97_codec ac97_bus snd_seq snd_seq_device
snd_pcm snd_timer snd soundcore snd_page_alloc i2c_i801 sg lpc_ich mfd_core ext4
jbd2 mbcache sr_mod cdrom sd_mod crc_t10dif pata_acpi ata_generic ata_piix
radeon ttm drm_kms_helper drm i2c_algo_bit i2c_core dm_mirror dm_region_hash
dm_log dm_mod [last unloaded: mperf]

Pid: 4219, comm: nfsd Not tainted 2.6.32-491.el6.i686 #1 Dell Computer
Corporation OptiPlex GX240               /OptiPlex GX240
EIP: 0060:[<c04107b5>] EFLAGS: 00010246 CPU: 0
EIP is at nommu_map_page+0x15/0x110
EAX: 00000000 EBX: c0a83480 ECX: 00000000 EDX: 00800000
ESI: 00000000 EDI: f70e7860 EBP: e2d09b54 ESP: e2d09b24
 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process nfsd (pid: 4219, ti=e2d08000 task=e2ceaaa0 task.ti=e2d08000)
Stack:
 00000056 00000000 0000000e c65efd38 00000020 00000296 00000206 00000206
<0> c050c850 c0a83480 e2cef154 00000001 e2d09ba8 f8fcd585 00000510 00000001
<0> 00000000 00000000 f5172200 f8fdac00 0039ef8c f5277020 f70e7860 00000510
Call Trace:
 [<c050c850>] ? page_address+0xd0/0xe0
 [<f8fcd585>] ? boomerang_start_xmit+0x3b5/0x520 [3c59x]
 [<c07b2975>] ? dev_hard_start_xmit+0xe5/0x400
 [<f9182b00>] ? ip6_output_finish+0x0/0xf0 [ipv6]
 [<c07ca053>] ? sch_direct_xmit+0x113/0x180
 [<c07d5588>] ? nf_hook_slow+0x68/0x120
 [<c07b2ea5>] ? dev_queue_xmit+0x1b5/0x290
 [<f9182b6d>] ? ip6_output_finish+0x6d/0xf0 [ipv6]
 [<f9184cb8>] ? ip6_xmit+0x3e8/0x490 [ipv6]
 [<f91ab9f9>] ? inet6_csk_xmit+0x289/0x2f0 [ipv6]
 [<c07f6451>] ? tcp_transmit_skb+0x431/0x7f0
 [<c07a403f>] ? __alloc_skb+0x4f/0x140
 [<c07f85a2>] ? tcp_write_xmit+0x1c2/0xa50
 [<c07f90b1>] ? __tcp_push_pending_frames+0x31/0xe0
 [<c07ea47a>] ? tcp_sendpage+0x44a/0x4b0
 [<c07ea030>] ? tcp_sendpage+0x0/0x4b0
 [<c079be1e>] ? kernel_sendpage+0x4e/0x90
 [<f8457bb9>] ? svc_send_common+0xc9/0x120 [sunrpc]
 [<f8457c85>] ? svc_sendto+0x75/0x1f0 [sunrpc]
 [<c060d0d9>] ? _atomic_dec_and_lock+0x59/0x90
 [<f87d55d0>] ? nfs3svc_encode_readres+0x0/0xc0 [nfsd]
 [<f845876d>] ? svc_authorise+0x2d/0x40 [sunrpc]
 [<f87d4410>] ? nfs3svc_release_fhandle+0x0/0x10 [nfsd]
 [<f8455721>] ? svc_process_common+0xf1/0x5a0 [sunrpc]
 [<f8457e86>] ? svc_tcp_sendto+0x36/0xa0 [sunrpc]
 [<f8461778>] ? svc_send+0x98/0xd0 [sunrpc]
 [<f87c698c>] ? nfsd+0xac/0x140 [nfsd]
 [<c04470e0>] ? complete+0x40/0x60
 [<f87c68e0>] ? nfsd+0x0/0x140 [nfsd]
 [<c04802ac>] ? kthread+0x7c/0xa0
 [<c0480230>] ? kthread+0x0/0xa0
 [<c0409f9f>] ? kernel_thread_helper+0x7/0x10
Code: 8d b6 00 00 00 00 eb f8 8d b4 26 00 00 00 00 8d bc 27 00 00 00 00 55 89 e5
83 ec 30 89 75 f8 31 f6 89 7d fc 89 c7 89 c8 89 5d f4 <8b> 1a 8b 4d 08 c1 eb 19
c1 e3 04 8b 9b c0 29 c7 c0 83 e3 fc 29

But the problem seems to still exist upstream.  It seems on 32 bit kernels
page_address() can reutrn a NULL value in some circumstances, and the
pci_map_single api isn't prepared to handle that (on this system it results in a
bogus pointer deference in nommu_map_page.

The fix is pretty easy, if we convert the 3c59x driver to use the more
convieient skb_frag_dma_map api we don't need to find the virtual address of the
page at all, and page gets mapped to the hardware properly.  Verified to fix the
problem as described by the reporter.

Applies to the net tree

Change Notes:

v2) Converted PCI_DMA_TODEVICE to DMA_TO_DEVICE.  Thanks Dave!

v3) Actually Run git commit after making changes to v2 :)
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: klassert@mathematik.tu-chemnitz.de
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify the interrupt resource lookup code in cpsw_probe() by the
following:

 * Only look at the first member of the resource. As the driver only
   works for DT-enabled platforms anyway, a resource of type
   IORESOURCE_IRQ will only contain one single entry
   (res->start == res->end), so there is no need for the iteration.

 * Add a bounds check to avoid overflows if we are passed more than
   ARRAY_SIZE(priv->irqs_table) resources.

 * Assign 'ret' with the return value of devm_request_irq() so that
   cpsw_probe() returns the appropriate error code.

 * If devm_request_irq() fails, report the error code in the log
   message.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NMugunthan V N <mugunthanvnm@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch contains fixes identified by checkpatch when run with the
strict option.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for setting/getting rx_copybreak using
generic ethtool tunable.

Defines enic_get_tunable() & enic_set_tunable() to get/set rx_copybreak.
As of now, these two function supports only rx_copybreak.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling dma_map_single()/dma_unmap_single() is quite expensive compared
to copying a small packet. So let's copy short frames and keep the buffers
mapped.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we bring the interface down, phy_stop() will schedule the PHY
state machine to call our link adjustment callback. By the time we do so,
we may have clock gated off the SYSTEMPORT hardware block, and this will
cause bus errors to happen in bcm_sysport_adj_link():

Make sure that we only touch the UMAC_CMD register when there is an
actual link. This is safe to do for two reasons:

- updating the Ethernet MAC registers only make sense when a physical
  link is present
- the PHY library state machine first set phydev->link = 0 before
  invoking phydev->adjust_link in the PHY_HALTED case

This is a similar fix to the GENET one:
c677ba8b ("net: bcmgenet: update
UMAC_CMD only when link is detected").

Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hardware has a limited number of pools available (64). Previously, no
checks were in place to limit the number of accelerated macvlan devices
based on the number of pools. Normally this would be ok, because there
was already a limit for these well below the number of available pools.
However, SR-IOV uses the very same pools. Therefor, we need to ensure
that the total number of pools (number of VFs plus the number of non-VF
pools in use for accelerated macvlans) does not exceed the number of
pools available in hardware.

This patch resolves a kernel NULL pointer dereference caused by the following commands:

$modprobe ixgbe max_vfs=63

$ethtool -K eth2 l2-fwd-offload on

$ip link add link eth2 macvlan0 type macvlan

$ip link set dev macvlan0 up

[  992.950080] BUG: unable to handle kernel NULL pointer dereference at 0000000000000056
[  992.951109] IP: [<ffffffffa003b71e>] ixgbe_disable_fwd_ring+0x1e/0xf0 [ixgbe]
[  992.951684] PGD 22a80e067 PUD 232e9b067 PMD 0
[  992.952389] Oops: 0000 [#1] SMP
[  992.953014] Modules linked in: nfsd lockd nfs_acl exportfs auth_rpcgss oid_registry sunrpc bridge stp llc vhost_net macvtap macvlan vhost tun kvm_intel kvm ioatdma ixgbe mdio igb dca
[  992.956042] CPU: 2 PID: 11928 Comm: ifconfig Not tainted 3.16.0-rc6-net-next-07-29-2014-FCoE+ #1
[  992.956915] Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.03.0003.041920141333 04/19/2014
[  992.957791] task: ffff8804341c0000 ti: ffff8801d7dc8000 task.ti: ffff8801d7dc8000
[  992.958660] RIP: 0010:[<ffffffffa003b71e>]  [<ffffffffa003b71e>] ixgbe_disable_fwd_ring+0x1e/0xf0 [ixgbe]
[  992.959613] RSP: 0018:ffff8801d7dcbbb8  EFLAGS: 00010286
[  992.960093] RAX: 0000000000000001 RBX: 0000000000000000 RCX: 0000000000000001
[  992.960575] RDX: ffff880232eb7000 RSI: 0000000000000000 RDI: ffff88022dc05800
[  992.961059] RBP: ffff8801d7dcbbd8 R08: 0000000000000000 R09: 0000000000000000
[  992.961541] R10: 0000000000000001 R11: 0000000000000000 R12: ffff88022ec20980
[  992.962023] R13: ffff880232eb7000 R14: 0000000000000001 R15: 0000000000000001
[  992.962508] FS:  00007fab264887a0(0000) GS:ffff880237640000(0000) knlGS:0000000000000000
[  992.963378] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  992.963858] CR2: 0000000000000056 CR3: 000000022a939000 CR4: 00000000001427e0
[  992.964340] Stack:
[  992.964806]  ffff88022ec28840 ffff88022ec20980 ffff88022dc05800 ffff880232eb7000
[  992.965976]  ffff8801d7dcbc28 ffffffffa003bae8 ffff8801d7dcbbe8 0000000000000400
[  992.967147]  000000000000000d ffff88022ec20980 ffff88022ec20000 ffff88022dc05800
[  992.968319] Call Trace:
[  992.968795]  [<ffffffffa003bae8>] ixgbe_fwd_ring_up+0x88/0x280 [ixgbe]
[  992.969284]  [<ffffffffa0041d83>] ixgbe_fwd_add+0x173/0x220 [ixgbe]
[  992.969767]  [<ffffffffa015056c>] macvlan_open+0x1bc/0x230 [macvlan]
[  992.970256]  [<ffffffff816b8de7>] __dev_open+0xd7/0x150
[  992.970735]  [<ffffffff816b8bd7>] __dev_change_flags+0xa7/0x170
[  992.971220]  [<ffffffff816b8ccb>] dev_change_flags+0x2b/0x70
[  992.971703]  [<ffffffff817471b2>] devinet_ioctl+0x602/0x6d0
[  992.972184]  [<ffffffff81748168>] inet_ioctl+0x78/0x90
[  992.972666]  [<ffffffff816a143b>] sock_do_ioctl+0x2b/0x70
[  992.973146]  [<ffffffff816a14ed>] sock_ioctl+0x6d/0x260
[  992.973627]  [<ffffffff811ad3b4>] do_vfs_ioctl+0x84/0x540
[  992.974109]  [<ffffffff811a4c81>] ? final_putname+0x21/0x50
[  992.974593]  [<ffffffff818725d5>] ? sysret_check+0x22/0x5d
[  992.975073]  [<ffffffff811ad901>] SyS_ioctl+0x91/0xa0
[  992.975550]  [<ffffffff818725a9>] system_call_fastpath+0x16/0x1b
[  992.976026] Code: ff 66 66 66 2e 0f 1f 84 00 00 00 00 00 55 48 89 e5 48 83 ec 20 48 89 5d e8 4c 89 65 f0 48 89 f3 4c 89 6d f8 4c 8b a7 08 02 00 00 <44> 0f b6 6e 56 44 03 af 14 02 00 00 4c 89 e7 e8 5e f2 ff ff be
[  992.982261] RIP  [<ffffffffa003b71e>] ixgbe_disable_fwd_ring+0x1e/0xf0 [ixgbe]
[  992.983212]  RSP <ffff8801d7dcbbb8>
[  992.983681] CR2: 0000000000000056
[  992.984248] ---[ end trace 9f54802b5cc3638b ]---

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since we previously called ixgbe_set_num_queues just prior to attempting
to set our interrupt scheme, it may be non obvious why we have to call
it again inside the function. Add a comment which helps make it more
obvious that we are resetting features based on the fact that we do not
have MSI-X enabled, and cannot use the previous settings.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

VFLINKS.LINKUP bit tends to flap when a DA or SFP+ cable is disconnected.
It can take up to 500 usecs for the LINKUP bit to be correct.

This patch resolves the issue by introducing a delay for 82599 VFs of at
least 500 usecs to make sure the VFLINKS value is correct.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe initiates a reset of the interface on link loss with pending Tx work
in order to clear the rings.

This patch extends the pending Tx work check to the VF interfaces with the
same purpose.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that the behavior for FDB handling is consistent
between both the SR-IOV and non-SR-IOV cases.  The main change here is that we
perform bounds checking on the number of SR-IOV addresses regardless of if
SR-IOV is enabled or not as we can only support a certain number of addresses
in the hardware.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is global funcion pci_vfs_assigned(), so use it instead of composing
local one.
Signed-off-by: NEthan Zhao <ethan.kernel@gmail.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump i40e version to 1.0.11 and i40evf version to 1.0.5.

Change-ID: I63a60fa2efe82aae87a8a3095f43218db57d46ce
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>

This fixes the panic under traffic load when resetting.  This issue
could also show up if/whenever there is a Tx-timeout.

Change-ID: Ie393a1f17fd5d962e56fc3bfe784899ef25402f5
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We shouldn't restart Admin queue subtask if PF reset fails since we do
not have the AQ setup at that point. This patch makes sure we disable AQ
clean subtask when PF reset fails.

This will resolve an occasional kernel panic when PF reset fails for
some reason.

Change-ID: I11a747773362a8c5c0ad7a10cd34be0bda8eb9e8
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver is un-necessarily printing a warning that is only marginally
useful to the user.  Make the warning only print if extended driver
string printing is enabled, other messages related to a reset event
will still continue to print.

Change-ID: I5e8beca6516a2f176cd2e72b0ac2b3b909e6c953
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since we don't seem to be getting an LSE telling us link is going down
during set_phy_config (but we do get an LSE telling us we are coming
back up), fake one for the OS and tell them link is going down. Also
do an atomic restart no matter what because there are times the user
may want to end with link up even if they started with link down (like
if they accidentally set it to a speed that can't link and are trying to
fix it).

Change-ID: I0a642af9c1d0feb67bce741aba1a9c33bd349ed6
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove unnecessary setting of "ret" variable as it's already set at
the top of the function.

Change-ID: Icaccfc67f335817a23579b7c43625d59ad6c9925
Signed-off-by: NSerey Kong <serey.kong@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change "spoofck" to "spoofchk" to be consistent with as defined in netdev.

Change-ID: I9866d6284cb5f92c8d71dc0776c6d1e71dfb62a5
Signed-off-by: NSerey Kong <serey.kong@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Allow the user to change auto-negotiation and speed settings if
link is down.

Change-ID: I372967c627682b5e1835f623a7cbf41b21b51043
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Now that fw has implemented dual speed module support, we can add ours.
Also, add the phy type for 1G LR/SR and set its media type to fiber.
Lastly, instead of a WARN_ON if the phy type is not recognized just print
a warning.

Change-ID: I2e5227d4a8c2907b0ed423038e5dbce774e466b0
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It would appear the mlx4_en driver was still making a call to
dev_kfree_skb_any() where dev_consume_skb_any() would be more
appropriate.  This should make dropped packet profiling/tracking
easier/better over a NIC driven by mlx4_en.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During allocation and initialization of the network driver structures,
the wrong pointer is used to initialize a spin lock. Fix the spin lock
initialization by using the proper pointer.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some hosts can be both little and big endian.
In certain scenarios a big endian kernel can kexec a little endian kernel.

This patch fixes this case from both ends:
1) Return endianity to original values on shutdown (in case little endian kernel boots after we shutdown).
2) Do not rely on HW reset values when loading driver in little endian kernel
   but configure them explicitly (in case previous kernel was big endian and did not reset the HW).
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>