Move plat/dma.h to plat-omap/dma-omap.h as part of single
zImage work
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

We need to remove this from plat for ARM common zImage
support.

Also remove includes not needed by the omap_hsmmc.c driver.

Cc: linux-mmc@vger.kernel.org
Acked-by: NChris Ball <cjb@laptop.org>
Acked-by: NVenkatraman S <svenkatr@ti.com>
[tony@atomide.com: fold in removal of unused driver includes]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add integration data for the hardware random number generator IP block
on some OMAP SoCs.  This appears to be present on at least OMAP2xxx
and OMAP3xxx SoCs, although it is not so easy to tell.  It may also be
present on other OMAP2+ SoCs.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add gpmc hwmod and associated interconnect data
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
[paul@pwsan.com: added comments to the use of HWMOD_INIT_NO_RESET]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

This can be local to mach-omap2.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.

This moves such data out of the omap include directories
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NTony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: "Benoît Cousson" <b-cousson@ti.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: Jean Pihet <j-pihet@ti.com>
Cc: J Keerthy <j-keerthy@ti.com>
Cc: linux-omap@vger.kernel.org

As the plat and mach includes need to disappear for single zImage work,
we need to remove plat/hardware.h.

Do this by splitting plat/hardware.h into omap1 and omap2+ specific files.

The old plat/hardware.h already has omap1 only defines, so it gets moved
to mach/hardware.h for omap1. For omap2+, we use the local soc.h
that for now just includes the related SoC headers to keep this patch more
readable.

Note that the local soc.h still includes plat/cpu.h that can be dealt
with in later patches. Let's also include plat/serial.h from common.h for
all the board-*.c files. This allows making the include files local later
on without patching these files again.

Note that only minimal changes are done in this patch for the
drivers/watchdog/omap_wdt.c driver to keep things compiling. Further
patches are needed to eventually remove cpu_is_omap usage in the drivers.

Also only minimal changes are done to sound/soc/omap/* to remove the
unneeded includes and to define OMAP44XX_MCPDM_L3_BASE locally so there's
no need to include omap44xx.h.

While at it, also sort some of the includes in the standard way.

Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: NWim Van Sebroeck <wim@iguana.be>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

As the interrupts should only be defined in the platform_data, and
eventually coming from device tree, there's no need to define them
in header files.

Let's remove the hardcoded references to irqs.h and fix up the includes
so we don't rely on headers included in irqs.h. Note that we're
defining OMAP_INTC_START as 0 to the interrupts. This will be needed
when we enable SPARSE_IRQ. For some drivers we need to add
#include <plat/cpu.h> for now until these drivers are fixed to
remove cpu_is_omapxxxx() usage.

While at it, sort som of the includes the standard way, and add
the trailing commas where they are missing in the related data
structures.

Note that for drivers/staging/tidspbridge we just define things
locally.

Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This way we can remove includes of plat/gpio.h which won't work
with the single zImage support.

Note that we also remove the cpu_class_is_omap2() check
in gpio-omap.c as the drivers should not call it as we need to
make it local to arch/arm/mach-omap2 for single zImage support.

While at it, arrange the related includes in the standard way.

Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mtd@lists.infradead.org
Cc: alsa-devel@alsa-project.org
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove the existing alias for pad_fck, prcm_fck from the clock data and
add them as opt_clks to the hwmod data.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The enable/disable module functions are specific to SoCs with
OMAP4-class PRCM.  Rather than use cpu_is* checks at runtime inside
the enable/disable module functions, use cpu_is at init time to
initialize function pointers only for SoCs that need them.

NOTE: the cpu_is* check for _enable_module was different than
      the one for _disable_module, and this patch uses
      cpu_is_omap44xx() for both.
Signed-off-by: NKevin Hilman <khilman@ti.com>
[paul@pwsan.com: moved soc_ops function pointers to be per-kernel rather than
 per-hwmod since they do not vary by hwmod; added kerneldoc]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add 32k-sync timer hwmod-data and add ocp_if details to
omap2 & 3 hwmod table.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Reviewed-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add the HDQ1W hwmod for all OMAP2xxx devices.

Assume that OMAP2xxx chips have the same HDQ idle handling bug
as OMAP3:

   http://www.spinics.net/lists/linux-omap/msg63576.html

and set the OCPIF_SWSUP_IDLE flag accordingly on the HDQ's OCP interface.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

N800 logs this message on boot:

[    0.182281] omap_hwmod: iva: cannot be enabled for reset (3)

Fix by creating basic IVA1 and DSP hwmods for OMAP2420, and a basic IVA2
hwmod for OMAP2430.  There is still more information to be added, but
this should resolve the immediate issue.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Several struct omap_hwmod_ocp_if records can be shared between OMAP2420
and OMAP2430.  Move these shared records out of the chip-specific files
into mach-omap2/omap_hwmod_2xxx_interconnect_data.c.  This should save some
memory and source lines, at the cost of readability.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

After the link registration conversion, it's much easier to share some
hwmod data between OMAP2420 and 2430.  Move the shareable data into a
common file.  This should save some memory and lines of source, at the
cost of readability.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Reorganize the hwmod data to declare the IP blocks first and the
interconnects second.  This allows us to remove the forward
declarations, which this patch also does. Saves some lines of source
data.  While here, take the opportunity to synchronize the order of
the OMAP44xx hwmod data with the autogenerator output -- it's slightly
different due to past mismerges -- and fix a few minor typos and
whitespace problems in the files.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Register interconnect links between IP blocks, rather than the IP
blocks themselves.  (The IP blocks will be registered as a side-effect
of registering the links.)

The objective is to reduce the number of lines of static data and
facilitate the sharing of IP block data between different SoCs.  These
objectives come at the penalty of increased boot time due to increased
computation.

While here, fix a few whitespace problems and inaccurate variable names.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Some of the 2xxx and 3xxx hwmod data files use the old naming style
for hwmods, ending in a "_hwmod".  These names are used by the OMAP
integration code to map hwmods to platform_devices, so they need to be
consistent, or the platform_devices won't be created.  Remove the
_hwmod suffix to conform with the rest of the OMAP SoC data.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The clocks for all DSS slave interfaces were recently changed to "dss_ick" on
OMAP2 and OMAP3, this clock can be autoidled by PRCM. The VENC interface
previously had "dss_54m_fck" as it's clock which couldn't be autoidled, and
hence the OCPIF_SWSUP_IDLE flag was needed.

Remove the OCPIF_SWSUP_IDLE flag from VENC interfaces as it's clock is
now "dss_ick".  This allows the PRCM hardware to autoidle the VENC
interface clocks when they are not active, rather than relying on the
software to do it, which can keep the interface clocks active
unnecessarily.
Signed-off-by: NArchit Taneja <archit@ti.com>
[paul@pwsan.com: add a short description of the fix to the commit log]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Resetting DISPC when a DISPC output is enabled causes the DSS to go into an
inconsistent state. Thus if the bootloader has enabled a display, the hwmod code
cannot reset the DISPC module just like that, but the outputs need to be
disabled first.

Add function dispc_disable_outputs() which disables all active overlay manager
and ensure all frame transfers are completed.

Modify omap_dss_reset() to call this function and clear DSS_CONTROL,
DSS_SDI_CONTROL and DSS_PLL_CONTROL so that DSS is in a clean state when the
DSS2 driver starts.

This resolves the hang issue(caused by a L3 error during boot) seen on the
beagle board C3, which has a factory bootloader that enables display. The issue
is resolved with this patch.

Thanks to Tomi and Sricharan for some additional testing.
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: NR, Sricharan <r.sricharan@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
[paul@pwsan.com: restructured code, removed omap_{read,write}l(), removed
 cpu_is_omap*() calls and converted to dev_attr]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The OMAP2xxx HWMOD data currently contains two errors with DSS clocks:

- dss_rfbi is missing ick opt-clock, which is needed for RFBI to
  calculate timings

- dss_venc's interface and main clocks are wrong, causing VENC to fail
  to start

These problems were temporarily fixed with a DSS patch
9ede365a ("HACK: OMAP: DSS2: clk hack
for OMAP2/3"), which can be reverted after this patch (and the similar
patches for other OMAPs).
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

DSS needs all DSS clocks to be enabled to be able to finish reset
properly. Before v3.1-rc1 the omapdss driver was managing clocks and
resets correctly. However, when omapdss started using runtime PM at
v3.1-rc1, the responsibility for the reset moved to HWMOD framework.

HWMOD framework does not currently enable all the DSS clocks when
resetting the DSS hardware. This hasn't caused any problems so far, but
we may just have been lucky.

This patch sets HWMOD_CONTROL_OPT_CLKS_IN_RESET for dss_core in OMAP2xxx
HWMOD data, fixing the issue.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: merged duplicate .flags fields]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add routines to converts dmtimers to platform devices. The device data
is obtained from hwmod database of respective platform and is registered
to device model after successful binding to driver.
In addition, capability attribute of each of the timers is added in
hwmod database.
Signed-off-by: NTarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: NThara Gopinath <thara@ti.com>
Reviewed-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NCousson, Benoit <b-cousson@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

At Tony's request, remove the OMAP_CHIP* flags from the hwmod data, and
replace it instead with chip family, variant, and ES level-specific lists
of hwmods to register.

Thanks to Gražvydas Ignotas <notasas@gmail.com> for finding a bug in the
AM3517/3505 support, and for other review comments.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Gražvydas Ignotas <notasas@gmail.com>

Add a missing array terminator to omap2430_usbhsotg_addrs[].  Without
this terminator, the omap_hwmod resource building code runs off the
end of the array, resulting in at least this error -- if not worse
behavior:

[    0.578002] musb-omap2430: failed to claim resource 4
[    0.583465] omap_device: musb-omap2430: build failed (-16)
[    0.589294] Could not build omap_device for musb-omap2430 usb_otg_hs

This should have been part of commit
78183f3f ("omap_hwmod: use a null
structure record to terminate omap_hwmod_addr_space arrays") but was
evidently missed.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The sequence of _ocp_softreset doesn't work for i2c. The i2c module has a
special sequence to reset the module. The sequence is
 - Disable the I2C.
 - Write to SOFTRESET bit.
 - Enable the I2C.
 - Poll on the RESETDONE bit.
The sequence is implemented as a function and the i2c_class is updated with
the correct 'reset' pointer.  omap_hwmod_softreset function is implemented
which triggers the softreset by writing into sysconfig register. On following
this sequence, i2c module resets properly and timeouts are not seen.

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: NAvinash.H.M <avinashhm@ti.com>
[paul@pwsan.com: combined this patch with a patch to remove
 HWMOD_INIT_NO_RESET from the 44xx hwmod flags; change register
 offset conditional code to use the IP block revision; minor code
 cleanup]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

This adds the new functionality flags for omap i2c unit to all OMAP2
hwmod definitions

Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NAndy Green <andy.green@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Since we cannot trust (or even reliably find) the OMAP I2C
peripheral unit's own revision register, we must inform the
OMAP i2c driver of which IP version it is running on.  We
do this by tagging the omap_hwmod_class for i2c on all the
OMAP2+ platform / cpu specific hwmod init and passing it up
to the driver (next patches).

Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NAndy Green <andy.green@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Peter Maydell noticed when running under QEMU he was getting
errors reporting 32-bit access to I2C peripheral unit registers
that are documented to be 8 or 16-bit only[1][2]

The I2C driver is blameless as it wraps its accesses in a
function using __raw_writew and __raw_readw, it turned out it
is the hwmod stuff.

However the hwmod code already has a flag to force a
perhipheral unit to only be accessed using 16-bit operations.

This patch applies the 16-bit only flag to the 2430,
OMAP3xxx and OMAP44xx hwmod structs.  2420 was already
correctly marked up as 16-bit.

The 2430 change will need testing by TI as arranged
in the comments to the previous patch version.

When the 16-bit flag is or-ed with other flags, it is placed
first as requested in comments.

[1] OMAP4430 Technical reference manual section 23.1.6.2
[2] OMAP3530 Techincal reference manual section 18.6

Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NAndy Green <andy.green@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

To reduce kernel source file data duplication, share struct
omap_hwmod_class and omap_hwmod_class_sysconfig arrays across OMAP2xxx
and 3xxx hwmod data files.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

To reduce kernel source file data duplication, share struct
omap_hwmod_dma_info arrays across OMAP2xxx and 3xxx hwmod data files.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Previously, struct omap_hwmod_dma_info arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array.  However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.

So far this hasn't been a problem.  However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file.  When this is done, ARRAY_SIZE() will no longer be usable.

This patch removes ARRAY_SIZE() usage for struct omap_hwmod_dma_info
arrays and uses a sentinel value (irq == -1) as the array terminator
instead.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

To reduce kernel source file data duplication, share struct
omap_hwmod_mpu_irqs arrays across OMAP2xxx and 3xxx hwmod data files.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Previously, struct omap_hwmod_mpu_irqs arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array.  However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.

So far this hasn't been a problem.  However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file.  When this is done, ARRAY_SIZE() will no longer be usable.

This patch removes ARRAY_SIZE() usage for struct omap_hwmod_mpu_irqs
arrays and uses a sentinel value (irq == -1) as the array terminator
instead.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

To reduce kernel source file data duplication, share struct
omap_hwmod_addr_space arrays across OMAP2xxx and 3xxx hwmod data
files.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Previously, struct omap_hwmod_addr_space arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array.  However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.

So far this hasn't been a problem.  However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file.  When this is done, ARRAY_SIZE() will no longer be usable.

This patch removes ARRAY_SIZE() usage for struct omap_hwmod_addr_space
arrays and uses a null structure member as the array terminator
instead.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

GPIO module expects the debounce clocks to be enabled during reset. It doesn't
reset properly and timeouts are seen, if this clock isn't enabled during
reset. Add the HWMOD_CONTROL_OPT_CLKS_IN_RESET flags to the GPIO HWMODs, with
which the debounce clocks are enabled during reset.

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: NAvinash.H.M <avinashhm@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

OMAP2420, 2430 and 3xxx were using the OMAP4 end address
that unfortunately is not located at the same base address.
Moreover the OMAP4 size was set to 256 instead of 4096.

Change all .pa_end to set them to .pa_start + 0xfff

Cc: "G, Manjunath Kondaiah" <manjugk@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Reported-by: NMichael Fillinger <m-fillinger@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>