NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.

Libraries like libnl will wait forever for NLMSG_DONE.

Fixes: e5a55a89 ("net: create generic bridge ops")
Fixes: 815cccbf ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The numPosted field in the ERX Doorbell register is 8-bits wide.
So the max buffers that we can post at a time is 255 and not 256
which we are doing currently.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch sets up xps queue mapping on load, so that TX traffic is
steered to the queue whose irqs are being processed by the current cpu.
This helps in avoiding TX lock contention.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch provides hints to irqbalance to map be2net IRQs to
specific CPU cores. cpumask_set_cpu_local_first() is used, which first
maps IRQs to near NUMA cores; when those cores are exhausted, IRQs are
mapped to far NUMA cores.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When an EEH error occurs, the device/slot is disconnected. This condition
is more reliably detected (i.e., returns all ones) with an MMIO read rather
than a config read -- especially on power platforms.

Hence, this patch fixes EEH error detection by replacing config reads with
MMIO reads for reading the error registers. The error registers in
Skyhawk-R/BE2/BE3 are accessible both via the config space and the
PCICFG (BAR0) memory space.
Reported-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NSuresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, a PF does not restrict its VF interface from enabling vlan
promiscuous mode. This breaks vlan isolation when a vlan
(transparent tagging) is configured on a VF.

This patch fixes this problem by disabling the vlan promisc capability
for VFs.
Reported-by: NYoann Juet <veilletechno-irts@univ-nantes.fr>
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements the .sriov_configure() PCI method to allow for
runtime enabling/disabling of VFs. The module param "num_vfs" is now
deprecated.
At the time of driver load the PF-pool resources are allocated to the PF.
When the user enables VFs, the resources are then re-distributed across
PFs and VFs based on the number of VFs enabled.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When SR-IOV is enabled in the adapter, the FW distributes resources
evenly across the PF and it's VFs. This is currently done only for some
resources.

This patch adds support for a new cmd that queries the FW for the list
of resources for which the distribution is allowed and distributes them
accordingly.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On BE2, BE3 and Skhawk-R chips one non-RSS (called "default") RXQ was
needed to receive non-IP traffic. Some FW versions now export a
capability called IFACE_FLAGS_DEFQ_RSS where this requirement doesn't hold.
On such FWs the driver now does not create the non-RSS default queue.
This prevents wasting one RXQ per VF.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the built-in function instead of memset.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Every time be_setup() is called, the driver will have to wait for the
function/FW to be properly initialized. So, it make sense to move this call
inside be_setup().
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most of the resource cleanup sequences performed in be_suspend(),
be_eeh_err_detected() and be_err_detection_task() are same. Moved the
common code to a new routine be_cleanup() to avoid code duplication.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most of the adapter initialisation sequences performed in be_resume(),
be_eeh_resume() and be_err_recover() are same. Renamed be_resume() to
be_pci_resume() and moved the common code to a new routine be_resume() to
avoid code duplication.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The steps needed for Lancer's reset/initialization sequence are:
	a) wait for SLIPORT_STAUS RDY bit to be set
	b) set the SLIPORT_CONTROL IP bit
	c) repeat step "a"

The code needed for this sequence is already covered by the be_func_init()
routine (with minor modifications.) So, get rid of the
lancer_test_and_set_rdy_state() and lancer_provisioning_error() routines
that unnecessarily duplicate this code. Also fixed the error recovery
function to take care of these changes
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when an error is detected, the queue resources are being cleaned up
in the recovery routine. The resources are better cleaned up in the error
detection routine itself (similar to EEH code.)
So, this patch re-factors error processing logic to follow the following sequence:
	- check if there is an error in adapter
	- if error,
		- cleanup resources
		- attempt recovery

The patch renames lancer_recover_func() to be_err_recover() as this
routine will be used in the future for error recovery on Skyhawk too.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also rename func_recovery_work/task to err_detection_work/task as error
detection is the primary goal of this task while recovery is not guaranteed.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function initialization sequence is executed in be_probe(), be_resume
and be_eeh_resume(). Move this code to a new routine called be_func_init()
to prevent code duplication.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most of the code to fetch the adapter state is in be_setup()->be_get_config().
So, move the code from be_get_initial_config() to be_get_config().
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The members of be_adapter struct were being allocated in two separate
routines -- be_ctrl_init() and be_stats_init(). Also, some other members
were allocated elsewhere. This patch moves the alloc/free code into
be_drv_init/cleanup() routines. The be_pci_map_bars() routine that was
called from be_ctrl_init() is now called directly from be_probe().
The new routine be_drv_init() will now be the place-holder for allocating
memory for any new be_adapter{} members in the future.
Some routines needed to be moved to provide forward definitions for their
calls.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Check qfull condition
- Check qwake condition
- Check pkts pending completion
Signed-off-by: NSriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- To avoid multiple accesses to CQE, extract compl_status and end_idx from
  be_tx_compl_get().
Signed-off-by: NSriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Reduce code duplication by moving WRB-frags setup into a function.
- Do not setup WRB-header before frags are setup, which is unncessary if
  there's errors while setting up frags. We should only grab an entry for
  the header, setup the frags and if everything is fine setup the header.
- The error cleanup can be moved into a small function.
Signed-off-by: NSriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The WRB header is setup by wrb_fill_hdr() routine. This routine currently
gets some of the WRB params as args and figures out rest of the WRB params
by looking at various fields in skb (like gso, checksum, vlan-tag etc).
All these params could instead be retrieved from the skb into a structure
and passed to this routine. This separates wrb_fill_hdr() to only provide
chip-specific code to fill the WRB. This also makes it simple to support
chips with different WRB formats.
Signed-off-by: NSriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch "module: fix types of device tables aliases" newly requires that
invocations of

MODULE_DEVICE_TABLE(type, name);

come *after* the definition of `name'.  That is reasonable, but some
drivers weren't doing this.  Fix them.

Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: David Miller <davem@davemloft.net>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The 32-bit fields of a tx-wrb are little endian. The driver is currently
using be_dws_le_to_cpu() routine to swap (cpu to le) all the fields of
a tx-wrb. So, the rsvd field is also unnecessarily swapped.

This patch fixes this by individually swapping the required fields.
Also, the type of the fields in eth_tx_wrb{} is now changed to __le32
from u32 to avoid sparse warnings.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for processing the port misconfigure async
event generated by the FW. This event is generated typically when an
optical module is incorrectly installed or is faulty.

This patch also moves the port_name field to the adapter struct for
logging the event. As the be_cmd_query_port_name() call is now moved
to be_get_config(), it is modified to use the mailbox instead of MCCQ
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch re-factors the filter setting (uc-list, mc-list, promisc, vlan)
code in be_set_rx_mode() and be_vid_config() to make it more readable
and reduce code duplication.
This patch adds a separate field to track the state/mode of filtering,
along with moving all the filtering related fields to one place in be
be_adapter structure.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch passes BE_IF_FLAGS_XXX flags to be_cmd_rx_filter() routine
instead of the IFF_XXX flags. Doing this gets rid of the code to convert
the IFF_XXX flags to the BE_IF_FLAGS_XXX used by the FW cmd. The patch
also removes code for setting if_flags_mask that was duplicated for each
filter mode.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While sending FW update cmds to the FW, the driver specifies the "type"
of each component that needs to be flashed. The FW then picks the offset
in the flash area at which the componnet is to be flashed. This doesn't work
when new components that the current FW doesn't recognize, need to be
flashed. Recent FWs (10.2 and above) support a scheme of FW-update wherein
the "offset" of the component in the flash area can be specified instead
of the "type". This patch uses the "offset" based FW-update mechanism and
only when it fails, it fallsback to the old "type" based update.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Skyhawk-B0 FW UFI is not compatible to flash on Skyhawk-P2 ASIC.
But, Skyhawk-P2 FW UFI is compatible with both B0 and P2 chips.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch re-factors the code that checks for flash file compatibility with
the chip type, for better readability, as follows:
	- be_get_ufi_type() returns the UFI type from the flash file
	- be_check_ufi_compatibility() checks if the UFI type is compatible
	  with the adapter/chip that is being flashed
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Routines that are called only inside one src file must remain in that
file itself. Including them in a header file that is used for exporting
routine/struct definitions, causes unnecessary compilation of other
src files, when such a routine is modified.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bridge flags are needed inside ndo_bridge_setlink/dellink handlers to
avoid another call to parse IFLA_AF_SPEC inside these handlers

This is used later in this series
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some FW cmd related definitions were included in be_hw.h
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Lancer FW is picky about requiring a function reset FW cmd as a part
of the initialization sequence.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the FW cmd to set flow control fails, the adapter state must simply
reflect the old values.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This removes a bit of duplication of code that initializes the en_flags.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Other tunnels like GRE break while VxLAN offloads are enabled in Skyhawk-R. To
avoid this, we should restrict offload features on a per-packet basis in such
conditions.
Signed-off-by: NSriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The same macros are used for rx as well. So rename it.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch uses skb->xmit_more flag to batch TX requests.
TX is flushed either when xmit_more is false or there is
no more space in the TXQ.

Skyhawk-R and BEx chips require an even number of wrbs to be posted.
So, when a batch of TX requests is accumulated, the last header wrb
may need to be fixed with an extra dummy wrb.

This patch refactors be_xmit() routine as a sequence of be_xmit_enqueue()
and be_xmit_flush() calls. The Tx completion code is also
updated to be able to unmap/free a batch of skbs rather than a single
skb.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>