IQ calibration doesn't complete and times out for half/quarter
rates, so skip it correctly.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TX_IQ_ON_AGC_CAL should not be enabled for AR9340. TX-IQ calibration
is run as part of AGC calibration only for AR9485, AR9462 and AR9565.
For the others (AR9300, AR9330, AR9340), TX-IQ cal is done independent
of AGC-cal.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is not enabled for any chip and is unused.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Doing this in ath9k_hw_fill_cap_info() is odd and it's
cleaner to do this in the init function for calibration.
Also, setup the supported calibration type in init_cal_settings.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

An issue is reported in AR9462 & AR9565 that NF_cal_not_done is
not observed when HW peak detector calibration is disabled. At that
state, the HW is stuck at NF calibration which prevents tx output.
The root cause is wrong peak detector offset calibrated by HW. To
resolve this issue, peak detector calibration is done manually by SW
for AR9462 and AR9565.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Whenever i_coff of IQ calibration is too high, AR9565 drops max
rx rate to MCS4. Skipping IQ update at this time can avoid this
problem for AR9565.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Noise floor calibration is performed on longcal interval and
the reading will be updated in history buffer. On rare occasions,
the previous noisefloor calibration might not be completed within
the period and trying to load nf reading will be failed. In such
situation, postpone the nf cabliration to next cycle to give
enough time to complete the calibration. This was already taken
care for ar9002 chips.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The chain index to perform IQ calibration is counted to number of valid
tx chains and then used for indexing chain specific registers. If the
chainmask is set to 0x2 (i.e chain 1 only), still it accesses chain 0
registers for chain 1. So use real chain index instead sequential one.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

MCI has to be handled only when BTCOEX is actually enabled.
Check for this condition before calling MCI related functions
from various reset/calibration call-sites.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes multiple issues with the current RTT
implementation in ath9k.

* The data that is obtained from the RTT interface registers
  are stored in 31:5 - mask out the extra bits when reading them.

* A history buffer is maintained which is not needed at all.
  Remove this array and just store the baseband data for each
  chain (or bank).

* A 'num_readings' variable was being used to handle the
  last entry. But it was being used in an improper manner, with
  the result that the RTT values were never being written
  to the RTT Interface registers. Fix this by using a simple
  flag.

* Stop baseband operations before programming the calibration values
  to the HW.

* Do not restore RX gain settings as part of RTT.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It does not work properly and reduces throughput.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add ATH_DBG_ to macros to shorten the uses and
reduce the line count.

Coalesce ath_dbg formats.
Add missing spaces to coalesced formats.
Add missing newline terminations to ath_dbg formats.
Align ath_dbg arguments where appropriate.
Standardize ath_dbg formats without periods.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  Add missed space and change typo in calibration debugging log.
Signed-off-by: NNikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

WLAN communicates with BT for its calibration by sending WLAN_CAL_REQ,
waits for BT_CAL_GRANT. This is done with the help of GPM messages.
also WLAN_CAL_DONE messages is sent once WLAN calibration is done.

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During the fast channel change noise floor values are being loaded
twice at init_cal and after channel_change. The commit "ath9k_hw:
Improve fast channel change for AR9003 chips" overlooked it that
caused failure to load nf while doing bgscan. This patch performs noise
floor calibration after the fast and full reset.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IQ calibration during fast channel change sometimes failed
with RTT. And also restoring invalid radio retention readings
during init cal could cause failure to set the channel properly.
This patch counts the valid rtt history readings and clears
rtt mask.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Support the fast channel change across band switch only when there
are available of reusable cabliration results. And also observed that
doing agc control calibration on fastcc, sometimes causing calibration
timeout. Hence changing agc control to be run only on full chip reset.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Supported calibrations of radio retention table (RTT) are
	- DC offset
	- Filter
	- Peak detect
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently Tx IQ calibration is enabled by default for all AR9003
chips. But for AR9480, the calibration status should be read from
chip after processing ini. And also the carrier leak calibration
status is checked during init cal. As the init_cal is being called
for fast channel change too, the tx_cl status only be read after
full reset. Hence moving that into process ini function.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support to reuse Carrier leak calibration
during fast channel change for AR9480 chips.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Pass an argument to decide whether to reuse the Tx IQ
calibration measurements or not during fast channel change.
This will be later used by MCI support for AR9480.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to reduce the overall scan time, fast channel change
should be implemented properly. This patch adds fast channel
change support across band switch or channel mode switch
instead of doing full chip reset. During the fastcc, tx iqcal
measurements are preserved and will be reloaded after successful
the channel change.

This patch also addressed fast channel issue where the STA can not
see APs in higher than operating channel on 5GHz band after
the association.

Cc: Paul Stewart <pstew@google.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently during the full reset, the nf calibration is always
restarted from the defaults. The noise floor history buffers are
never be used again after the scan and ath reset. This patch
ensures that nf histories are always be used that helps to
improve the signal quality on congested environment
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do the magnitude/phase coeff correction only if the outlier
is detected. Updating wrong magnitude/phase coeff factor
impacts not only tx gain setting but also leads to poor
performance in congested networks. In the clear environment
the impact is very minimal because the outlier happens
very rarely according to the past experiment. It occured
less than once every 1000 calibrations.

Cc: stable@kernel.org
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k_hw: Fix Tx IQ Calibration hang issue in
AR9003 chips" did not consider more than one potential sample
while calculating magnitude/phase average if more than one
sample has the same value which could affect post-processing
of outlier detection that causes an undesirable Tx IQ
correction value will be assigned to tx gain settings where
outlier happens.

Cc: Kai Shi <kaishi@qca.qualcomm.com>
Reported-by: NPaul Stewart <pstew@google.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NPaul Stewart <pstew@google.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The chainmasks were already configured at process_ini
before doing init calibration.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The Times They Are a-Changin'.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On AR9003 chips, doing three IQ calibrations will possibly cause chip
in stuck state. In noisy environment, chip could receive
a packet during the middle of three calibrations and it causes
the conflict of HW access and the eventual failure. It also
causes IQ calibration outliers which results in poor Tx EVM.

The IQ Cal procedure is after resetting the chip, run IQ cal 3 times
per each cal cycle and find the two closest readings and average of two.
The advantage of running Tx IQ cal more than once is that we can compare
calibration results for the same gain setting over multiple iterations.
Most of the cases the IQ failures were observed after first pass.

For the AR9485 and later chips, Tx IQ Calibration is performed along
with AGC cal. But for pre-AR9485 chips, Tx IQ cal HW has to be separated
from the rest of calibration HW to avoid chip hang. After all
calibrations are done in HW, we can start SW post-processing.
By doing this way, we minimize the SW difference among all chips.

The order of calibration (run IQ cal before other calibration) is also
needed to avoid chip hang for chips before AR9485. This issue was
originally observed with AR9382.

During the issue kernel log was filled with following message
ath: timeout (100000 us) on reg 0xa640: 0x00000001 & 0x00000001 != 0x00000000
ath: timeout (100000 us) on reg 0xa2c4: 0x00158dd9 & 0x00000001 != 0x00000000
ath: Unable to reset channel (2412 MHz), reset status -5
ath: Unable to set channel
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use hw supported chains instead of hard coded values.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add multiple Tx IQ cal support to improve EVM accross
different power levels.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove ath/debug.h and the includes of these files.
Coalesce long formats.
Correct a few misspellings and missing "\n"s from these logging messages.
Remove unnecessary trailing space before a newline.
Remove ARRAY_SIZE casts, use printf type %zu
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.

   text	   data	    bss	    dec	    hex	filename
  11161	     56	   2136	  13353	   3429	drivers/net/wireless/ath/ath9k/ar9003_paprd.o.new
  11167	     56	   2136	  13359	   342f	drivers/net/wireless/ath/ath9k/ar9003_paprd.o.old
  15428	     56	   3056	  18540	   486c	drivers/net/wireless/ath/ath9k/eeprom_4k.o.old
  15451	     56	   3056	  18563	   4883	drivers/net/wireless/ath/ath9k/eeprom_4k.o.new
  14087	     56	   2560	  16703	   413f	drivers/net/wireless/ath/ath9k/eeprom_9287.o.old
  14036	     56	   2560	  16652	   410c	drivers/net/wireless/ath/ath9k/eeprom_9287.o.new
  10041	     56	   2384	  12481	   30c1	drivers/net/wireless/ath/ath9k/ani.o.new
  10088	     56	   2384	  12528	   30f0	drivers/net/wireless/ath/ath9k/ani.o.old
   9316	   1580	   2304	  13200	   3390	drivers/net/wireless/ath/ath9k/htc_drv_init.o.new
   9316	   1580	   2304	  13200	   3390	drivers/net/wireless/ath/ath9k/htc_drv_init.o.old
  16483	     56	   3432	  19971	   4e03	drivers/net/wireless/ath/ath9k/ar9003_phy.o.new
  16517	     56	   3432	  20005	   4e25	drivers/net/wireless/ath/ath9k/ar9003_phy.o.old
  18221	    104	   2960	  21285	   5325	drivers/net/wireless/ath/ath9k/rc.o.old
  18203	    104	   2960	  21267	   5313	drivers/net/wireless/ath/ath9k/rc.o.new
  19985	     56	   4288	  24329	   5f09	drivers/net/wireless/ath/ath9k/eeprom_def.o.new
  20040	     56	   4288	  24384	   5f40	drivers/net/wireless/ath/ath9k/eeprom_def.o.old
  23997	     56	   4984	  29037	   716d	drivers/net/wireless/ath/ath9k/ar5008_phy.o.old
  23846	     56	   4984	  28886	   70d6	drivers/net/wireless/ath/ath9k/ar5008_phy.o.new
  24285	     56	   3184	  27525	   6b85	drivers/net/wireless/ath/ath9k/ar9003_eeprom.o.old
  24101	     56	   3184	  27341	   6acd	drivers/net/wireless/ath/ath9k/ar9003_eeprom.o.new
   6834	     56	   1032	   7922	   1ef2	drivers/net/wireless/ath/ath9k/ar9002_phy.o.old
   6780	     56	   1032	   7868	   1ebc	drivers/net/wireless/ath/ath9k/ar9002_phy.o.new
  36211	     64	   8624	  44899	   af63	drivers/net/wireless/ath/ath9k/hw.o.new
  36401	     64	   8624	  45089	   b021	drivers/net/wireless/ath/ath9k/hw.o.old
   9281	     56	   1496	  10833	   2a51	drivers/net/wireless/ath/ath9k/ar9003_calib.o.old
   9150	     56	   1496	  10702	   29ce	drivers/net/wireless/ath/ath9k/ar9003_calib.o.new

Use ARRAY_SIZE instead of a magic number.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9382 needs to be configured for the correct chain mask before
running AGC/TxIQ caliberation. Otherwise reset would fail.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>