Skip to content

K
Kernel

openeuler / Kernel
大约 1 年 前同步成功

通知 6
Star 0
Fork 0
K
Kernel

体验新版 GitCode，发现更多精彩内容 >>

切换分支/标签
  1. 28 7月, 2009 2 次提交
    • R
      iwlagn: fix minimum number of queues setting · 45f5fa32
      由 reinette chatre 提交于 
      We need to provide a reasonable minimum that will result in a
working setup if used. Set minimum to be 10 to provide for
4 standard TX queues + 1 command queue + 2 (unused) HCCA queues +
4 HT queues (one per AC).

We allow the user to change the number of queues used via a module
parameter and use this minimum value to check if it is valid. Without
this patch a user can select a value for the number of queues that
will result in a failing setup.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Reviewed-by: NTomas Winkler <tomas.winkler@intel.com>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      45f5fa32
    • J
      iwlwifi: fix TX queue race · 3995bd93
      由 Johannes Berg 提交于 
      I had a problem on 4965 hardware (well, probably other hardware too,
but others don't survive my stress testing right now, unfortunately)
where the driver was sending invalid commands to the device, but no
such thing could be seen from the driver's point of view. I could
reproduce this fairly easily by sending multiple TCP streams with
iperf on different TIDs, though sometimes a single iperf stream was
sufficient. It even happened with a single core, but I have forced
preemption turned on.

The culprit was a queue overrun, where we advanced the queue's write
pointer over the read pointer. After careful analysis I've come to
the conclusion that the cause is a race condition between iwlwifi
and mac80211.

mac80211, of course, checks whether the queue is stopped, before
transmitting a frame. This effectively looks like this:

        lock(queues)
        if (stopped(queue)) {
                unlock(queues)
                return busy;
	}
        unlock(queues)
        ...             <-- this place will be important
			    there is some more code here
        drv_tx(frame)

The driver, on the other hand, can stop and start queues, which does

        lock(queues)
        mark_running/stopped(queue)
        unlock(queues)

	[if marked running: wake up tasklet to send pending frames]

Now, however, once the driver starts the queue, mac80211 can see that
and end up at the marked place above, at which point for some reason the
driver seems to stop the queue again (I don't understand that) and then
we end up transmitting while the queue is actually full.

Now, this shouldn't actually matter much, but for some reason I've seen
it happen multiple times in a row and the queue actually overflows, at
which point the queue bites itself in the tail and things go completely
wrong.

This patch fixes this by just dropping the packet should this have
happened, and making the lock in iwlwifi cover everything so iwlwifi
can't race against itself (dropping the lock there might make it more
likely, but it did seem to happen without that too).

Since we can't hold the lock across drv_tx() above, I see no way to fix
this in mac80211, but I also don't understand why I haven't seen this
before -- maybe I just never stress tested it this badly.

With this patch, the device has survived many minutes of simultanously
sending two iperf streams on different TIDs with combined throughput
of about 60 Mbps.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      3995bd93
  3. 27 7月, 2009 10 次提交
  5. 24 7月, 2009 4 次提交
  7. 23 7月, 2009 9 次提交
  9. 22 7月, 2009 15 次提交