Driver was taking max() of a size_t and u32 which causes complaint
about comparison of different types.

Stumbled on this accidently in my config, never used.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In wusb_cluster_id_get(), if no zero bits exist in wusb_cluster_id_table,
find_first_zero_bit() returns CLUSTER_IDS.

But it is impossible to detect that the bitmap is full because there
is an off-by-one error in the return value check.  It will cause
unexpected memory access by setting bit out of wusb_cluster_id_table
bitmap, and caller will get wrong cluster id.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: linux-usb@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The SH EHCI/OHCI driver hardcoded the CPU type in {ehci,ohci}-hcd.c.
So if we will add the new CPU, we had to add to the hcd driver each time.
The patch adds the CONFIG_USB_{EHCI,OHCI}_SH configuration. So if we
want to use the SH EHCI/OHCI, we only enable the configuration.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch moves the AMD PLL quirk code in OHCI/EHCI driver to pci-quirks.c,
and exports the functions to be used by xHCI driver later.

AMD PLL quirk disable the optional PM feature inside specific
SB700/SB800/Hudson-2/3 platforms under the following conditions:

1. If an isochronous device is connected to OHCI/EHCI/xHCI port and is active;
2. Optional PM feature that powers down the internal Bus PLL when the link is
   in low power state is enabled.

Without AMD PLL quirk, USB isochronous stream may stutter or have breaks
occasionally, which greatly impair the performance of audio/video streams.

Currently AMD PLL quirk is implemented in OHCI and EHCI driver, and will be
added to xHCI driver too. They are doing similar things actually, so move
the quirk code to pci-quirks.c, which has several advantages:

1. Remove duplicate defines and functions in OHCI/EHCI (and xHCI) driver and
   make them cleaner;
2. AMD chipset information will be probed only once and then stored.
   Currently they're probed during every OHCI/EHCI initialization, move
   the detect code to pci-quirks.c saves the repeat detect cost;
3. Build up synchronization among OHCI/EHCI/xHCI driver. In current
   code, every host controller enable/disable PLL only according to
   its own status, and may enable PLL while there is still isoc transfer on
   other HCs. Move the quirk to pci-quirks.c prevents this issue.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The devices of clocks are set to usbhs, so that
only usbhs common driver can invoke these clocks.
The dummy per port clocks are added to omap3
clock data base. This helps to invoke common
clock get APIs for omap3 and omap4.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The ehci and ohci drivers are simplified; Since
UHH and TLL initialization, clock handling are
done by common usbhs core driver, these functionalities
are removed from ehci and ohci drivers.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The prototype and defination of functions usb_ehci_init and
usb_ohci_init are removed. The ehci and ohci devices are
removed since usbhs device contains both ehci and ohci details.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The usbhs intialization is invoked by all omap3 and omap4
variant board files.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

A new usbhs platform device is defined;
this device will be the parent device of ehci and
ohci platform devices. the usbhs_init function
is defined which does the usbhs device initialization
and I/O mux of ehci and ohci.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

enabling and disabling the common clocks for ehci
and ohci is implemented. usbhs is a common parent
platform driver for EHCI and OHCI driver. This driver
receives the clock enable and disable requests
from ehci and ohci drivers.The UHH and TLL
initialization is also performed.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Create the ehci and ohci specific platform data structures.
The port enum values are made common for both ehci and ohci.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We already have both EHCI and OHCI there, so let's
rename to be sure everybody will understand the entire
USB HOST functionality is setup on this file.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

now that we have names on all memory bases, we can
switch to use platform_get_resource_byname() which
will make it simpler when we move to a setup where
OHCI and EHCI on OMAP play well together.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

add names to EHCI and OHCI resources. That will help us
identify the resource correctly when moving to a setup
where OHCI and EHCI play well together.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The EHCI controller in OMAP4 supports a transceiver-less link
mode (TLL mode), similar to the one in OMAP3. On the OMAP4
however, there are an additional set of clocks that need
to be turned on to get this working.

Request and configure these for each port if that port
is connected in TLL mode.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

tusb_dma was being dereferenced when it was nul
Signed-off-by: NHuzaifa Sidhpurwala <huzaifas@redhat.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In OMAP3xxx with OTG mode or host only mode, When the device
is inserted after the gadget driver loading the enumeration was not
through. This is because the mentor controller will start sensing the
ID PIN only after setting the session bit.
So after ID-GND, need to set the session bit for mentor to get it
configured as A device.

This is a fix to set the session bit again in ID_GND notification handler.
Tested with OMAP3630Zoom3 platform.
Signed-off-by: NHema HK <hemahk@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Powerdown the internal PHY during board init for OMAP44xx.
So that when musb is disabled core transition to retention/off
is not blocked.
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add the context save/restore for the control module register
used for OMAP4430 musb with UTMI embedded PHY interface.
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Update the last_event variable of otg_transceiver. This will be used in
the musb platform glue driver for runtime idling the device.
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch supports the retention and offmode support in the idle path for
musb driver using runtime pm APIs.

This is restricted to support offmode and retention only when device not
connected.When device/cable connected with gadget driver loaded,configured
to no idle/standby which will not allow the core transition to retention
or off.

There is no context save/restore done by hardware for musb in OMAP3
and OMAP4,driver has to take care of saving and restoring the context
during offmode.

Musb has a requirement of configuring sysconfig register to force
idle/standby mode and set the ENFORCE bit in module STANDBY register
for retention and offmode support.

Runtime pm and hwmod frameworks will take care of configuring to force
idle/standby when pm_runtime_put_sync is called and back to no
idle/standby when pm_runeime_get_sync is called.

Compile, boot tested and also tested the retention in the idle path on
OMAP3630Zoom3. And tested the global suspend/resume with offmode enabled.
Usb basic functionality tested on OMAP4430SDP.

There is some problem with idle path offmode in mainline, I could not test
with offmode. But I have tested this patch with resetting the controller
in the idle path when wakeup from retention just to make sure that the
context is lost, and restore path is working fine.

Removed .suspend/.resume fnction pointers and functions because there
is no need of having these functions as all required work is done
at runtime in the driver.

There is no need to call the runtime pm api with glue driver device
as glue layer device is the parent of musb core device, when runtime apis
are called for the child, parent device runtime functionality
will be invoked.

Design overview:

pm_runtime_get_sync: When called with musb core device takes care of
enabling the clock, calling runtime callback function of omap2430 glue
layer, runtime call back of musb driver and configure the musb sysconfig
to no idle/standby

pm_runtime_put: Takes care of calling runtime callback function of omap2430
glue layer, runtime call back of musb driver, Configure the musb sysconfig
to force idle/standby and disable the clock.

During musb driver load: Call pm_runtime_get_sync.

End of musb driver load: Call pm_runtime_put

During gadget driver load: Call pm_runtime_get_sync,
End of gadget driver load: Call pm_runtime_put if there is no device
or cable is connected.

During unload of the gadget driver:Call pm_runtime_get_sync if cable/device
is not connected.
End of the gadget driver unload : pm_runtime_put

During unload of musb driver : Call pm_runtime_get_sync
End of unload: Call pm_runtime_put

On connect of usb cable/device -> transceiver notification(VBUS and ID-GND):
pm_runtime_get_sync only if the gadget driver loaded.

On disconnect of the cable/device -> Disconnect Notification:
pm_runtime_put if the gadget driver is loaded.
Signed-off-by: NHema HK <hemahk@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

For OMAP3 and OMAP4 for offmode and retention support, musb
sysconfig is configured to force idle and standby with ENABLE_FORCE bit
of OTG_FORCESTNDBY set.
And on wakeup configure to no ilde/standby with resetting the ENABLE_FORCE
bit. There is not need to save and restore of this register anymore
so removed omap2430_save_context/omap2430_restore_context functions.
and also removed otg_forcestandby member of musb_context_registers
structure
Signed-off-by: NHema HK <hemahk@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

commit ad1adb89
(usb: musb: gadget: do not poke with gadget's list_head)
fixed a bug in musb where it was corrupting the list_head
which is supposed to be used by gadget drivers. While
doing that, I forgot to fix the usage in musb_gadget_dequeue()
method. Fix that.
Reported-by: NPavol Kurina <pavol.kurina@emsys.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When compiling this program the functionfs.h header cannot be found, producing:
ffs-test.c:40: fatal error: linux/usb/functionfs.h: No such file or directory

This patch also fixes the following warning:
ffs-test.c:453: warning: format ‘%4d’ expects type ‘int’, but argument 3 has type ‘size_t’
Signed-off-by: NDavidlohr Bueso <dave@gnu.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make sure that we check the return value of tty_port_tty_get.
Sometimes it may return NULL and we later dereference that.

The only place here is in kobil_read_int_callback, so fix it.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make sure that we check the return value of tty_port_tty_get.
Sometimes it may return NULL and we later dereference that.

There are several places to check. For easier handling,
tty_port_tty_get is moved directly to the palce where needed in
keyspan_pda_rx_interrupt.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove redundant "toggle" member from struct isp1760_qtd, and store toggle
status in struct isp1760_qh only.
Signed-off-by: NArvid Brodin <arvid.brodin@enea.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Replace the period calculation for INT packets with something readable. Seems
to fix a rare bug with quickly repeated insertion/removal of several USB
devices simultaneously (hub control INT packets).
Signed-off-by: NArvid Brodin <arvid.brodin@enea.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Consolidate printouts to use dev_XXX functions instead of an assortment of
printks and driver specific macros. Remove some unused code snippets and struct
members. Remove some unused function parameters and #defines. Change the
"queue_entry" variable name which has different but related meanings in
different places and use "slot" only.
Signed-off-by: NArvid Brodin <arvid.brodin@enea.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NArvid Brodin <arvid.brodin@enea.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Encapsulate payload addresses within qtds.
Signed-off-by: NArvid Brodin <arvid.brodin@enea.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Removes the redundant hw_next list pointer from struct isp1760_qtd, removes some
unused #defines, removes redundant "urb" member from struct inter_packet_info.
Signed-off-by: NArvid Brodin <arvid.brodin@enea.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This helps users with platform-bus-connected isp176xs, big-endian cpu,
and missing byteswapping on the data bus. It does so by collecting all
SW byteswaps in one place and also fixes a bug with non-32-bit io
transfers on this hardware, where payload has to be byteswapped
instead of ptds.
Signed-off-by: NArvid Brodin <arvid.brodin@enea.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Patch below removes one to many "n's" in a word..
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: linux-usb@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Patch below removes one to many "n's" in a word..
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: linux-usb@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The patch below removes an extra "l" in the word.
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The patch below removes an extra "l" in the word.
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add support for RTS and CTS line status
Signed-off-by: NMartin Jansen <martin.jansen@opticon.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Macro arguments used in expressions need to be enclosed in parenthesis
to avoid unpleasant surprises.
Signed-off-by: NDmitry Torokhov <dtor@vmware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When a driver doesn't know how much data a device is going to send,
the buffer size should be at least as big as the endpoint's maxpacket
value.  The serial drivers don't follow this rule; many of them
request only 256-byte bulk-in buffers.  As a result, they suffer
overflow errors if a high-speed device wants to send a lot of data,
because high-speed bulk endpoints are required to have a maxpacket
size of 512.

This patch (as1450) fixes the problem by using the driver's
bulk_in_size value as a minimum, always allocating buffers no smaller
than the endpoint's maxpacket size.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NFlynn Marquardt <flynn@flynnux.de>
CC: <stable@kernel.org> [after .39-rc1 is out]
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>