The libertas driver copies the SSID buffer back to the wireless core and
appends a trailing NULL character for termination. This is

a) unnecessary because the buffer is allocated with kzalloc and is hence
   already NULLed when this function is called, and

b) for priv->curbssparams.ssid_len == 32, it writes back one byte too
   much which causes memory corruptions.

Fix this by removing the extra write.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Maithili Hinge <maithili@marvell.com>
Cc: Kiran Divekar <dkiran@marvell.com>
Cc: Michael Hirsch <m.hirsch@raumfeld.com>
Cc: netdev@vger.kernel.org
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@lists.infradead.org
Cc: stable@kernel.org
Acked-by: NHolger Schurig <holgerschurig@gmail.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/iwlwifi/iwl-tx.c: In function `iwl_hw_txq_ctx_free':
drivers/net/wireless/iwlwifi/iwl-tx.c:410: warning: suggest explicit braces to avoid ambiguous `else'

Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The MIB counters are disabled when doing a chip reset.
Since ANI depends on the MIB registers for its operation, relying
on the contents of said registers during HW reset results in sub-optimal
performance.

Cc: stable@kernel.org
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When TX DMA termination has failed, the HW has to be reset
completely. Doing a fast channel change in this case is insufficient.
Also, change the debug level of a couple of messages to FATAL.

Cc: stable@kernel.org
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The internal, driver-specific maintenance of sequence
numbers is applicable only for HT frames.

Also, remove comments that are not relevant anymore.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix typo. The index should be multiplied by the entry size, not 'and'-ed.

Found via code-inspection.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some devices have 40MHz operation disabled entirely. Ensure that driver do
not enable 40MHz operation if a channel does not allow this.

This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2135Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

3945 updated write_ptr without regard to read_ptr on the Tx path.
This messes up our TFD on high load and result in the following:

<1>[ 7290.414172] IP: [<ffffffffa0dd53a1>] iwl3945_rx_reply_tx+0xc1/0x450 [iwl3945]
<4>[ 7290.414205] PGD 0
<1>[ 7290.414214] Thread overran stack, or stack corrupted
<0>[ 7290.414229] Oops: 0002 [#1] PREEMPT SMP
<0>[ 7290.414246] last sysfs file: /sys/devices/platform/coretemp.1/temp1_input
<4>[ 7290.414265] CPU 0
<4>[ 7290.414274] Modules linked in: af_packet nfsd usb_storage usb_libusual cpufreq_powersave exportfs cpufreq_conservative iwl3945 nfs cpufreq_userspace snd_hda_codec_realtek acpi_cpufreq uvcvideo lockd iwlcore snd_hda_intel joydev coretemp nfs_acl videodev snd_hda_codec mac80211 v4l1_compat snd_hwdep sbp2 v4l2_compat_ioctl32 uhci_hcd psmouse auth_rpcgss ohci1394 cfg80211 ehci_hcd video ieee1394 snd_pcm serio_raw battery ac nvidia(P) usbcore output sunrpc evdev lirc_ene0100 snd_page_alloc rfkill tg3 libphy fuse lzo lzo_decompress lzo_compress
<6>[ 7290.414486] Pid: 0, comm: swapper Tainted: P           2.6.32-rc8-wl #213 Aspire 5720
<6>[ 7290.414507] RIP: 0010:[<ffffffffa0dd53a1>]  [<ffffffffa0dd53a1>] iwl3945_rx_reply_tx+0xc1/0x450 [iwl3945]
<6>[ 7290.414541] RSP: 0018:ffff880002203d60  EFLAGS: 00010246
<6>[ 7290.414557] RAX: 000000000000004f RBX: ffff880064c11600 RCX: 0000000000000013
<6>[ 7290.414576] RDX: ffffffffa0ddcf20 RSI: ffff8800512b7008 RDI: 0000000000000038
<6>[ 7290.414596] RBP: ffff880002203dd0 R08: 0000000000000000 R09: 0000000000000100
<6>[ 7290.414616] R10: 0000000000000001 R11: 0000000000000000 R12: 00000000000000a0
<6>[ 7290.414635] R13: 0000000000000002 R14: 0000000000000013 R15: 0000000000020201
<6>[ 7290.414655] FS:  0000000000000000(0000) GS:ffff880002200000(0000) knlGS:0000000000000000
<6>[ 7290.414677] CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
<6>[ 7290.414693] CR2: 0000000000000041 CR3: 0000000001001000 CR4: 00000000000006f0
<6>[ 7290.414712] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
<6>[ 7290.414732] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
<4>[ 7290.414752] Process swapper (pid: 0, threadinfo ffffffff81524000, task ffffffff81528b60)
<0>[ 7290.414772] Stack:
<4>[ 7290.414780]  ffff880002203da0 0000000000000046 0000000000000000 0000000000000046
<4>[ 7290.414804] <0> 0000000000000282 0000000000000282 0000000000000282 ffff880064c12010
<4>[ 7290.414830] <0> ffff880002203db0 ffff880064c11600 ffff880064c12e50 ffff8800512b7000
<0>[ 7290.414858] Call Trace:
<0>[ 7290.414867]  <IRQ>
<4>[ 7290.414884]  [<ffffffffa0dc8c47>] iwl3945_irq_tasklet+0x657/0x1740 [iwl3945]
<4>[ 7290.414910]  [<ffffffff8138fc60>] ? _spin_unlock+0x30/0x60
<4>[ 7290.414931]  [<ffffffff81049a21>] tasklet_action+0x101/0x110
<4>[ 7290.414950]  [<ffffffff8104a3d0>] __do_softirq+0xc0/0x160
<4>[ 7290.414968]  [<ffffffff8100d01c>] call_softirq+0x1c/0x30
<4>[ 7290.414986]  [<ffffffff8100eff5>] do_softirq+0x75/0xb0
<4>[ 7290.415003]  [<ffffffff81049ee5>] irq_exit+0x95/0xa0
<4>[ 7290.415020]  [<ffffffff8100e547>] do_IRQ+0x77/0xf0
<4>[ 7290.415038]  [<ffffffff8100c7d3>] ret_from_intr+0x0/0xf
<0>[ 7290.415052]  <EOI>
<4>[ 7290.415067]  [<ffffffff81234efa>] ? acpi_idle_enter_bm+0x270/0x2a5
<4>[ 7290.415087]  [<ffffffff81234f04>] ? acpi_idle_enter_bm+0x27a/0x2a5
<4>[ 7290.415107]  [<ffffffff81234efa>] ? acpi_idle_enter_bm+0x270/0x2a5
<4>[ 7290.415130]  [<ffffffff812c11f3>] ? cpuidle_idle_call+0x93/0xf0
<4>[ 7290.415149]  [<ffffffff8100b0d7>] ? cpu_idle+0xa7/0x110
<4>[ 7290.415168]  [<ffffffff8137b3d5>] ? rest_init+0x75/0x80
<4>[ 7290.415187]  [<ffffffff8158cd0a>] ? start_kernel+0x3a7/0x3b3
<4>[ 7290.415206]  [<ffffffff8158c315>] ? x86_64_start_reservations+0x125/0x129
<4>[ 7290.415227]  [<ffffffff8158c3fd>] ? x86_64_start_kernel+0xe4/0xeb
<0>[ 7290.415243] Code: 00 41 39 ce 0f 8d e8 01 00 00 48 8b 47 40 48 63 d2 48 69 d2 98 00 00 00 4c 8b 04 02 48 c7 c2 20 cf dd a0 49 8d 78 38 49 8d 40 4f <c6> 47 09 00 c6 47 0c 00 c6 47 0f 00 c6 47 12 00 c6 47 15 00 49
<1>[ 7290.415382] RIP  [<ffffffffa0dd53a1>] iwl3945_rx_reply_tx+0xc1/0x450 [iwl3945]
<4>[ 7290.415410]  RSP <ffff880002203d60>
<0>[ 7290.415421] CR2: 0000000000000041
<4>[ 7290.415436] ---[ end trace ec46807277caa515 ]---
<0>[ 7290.415450] Kernel panic - not syncing: Fatal exception in interrupt
<4>[ 7290.415468] Pid: 0, comm: swapper Tainted: P      D    2.6.32-rc8-wl #213
<4>[ 7290.415486] Call Trace:
<4>[ 7290.415495]  <IRQ>  [<ffffffff8138c040>] panic+0x7d/0x13a
<4>[ 7290.415519]  [<ffffffff8101071a>] oops_end+0xda/0xe0
<4>[ 7290.415538]  [<ffffffff8102e1ea>] no_context+0xea/0x250
<4>[ 7290.415557]  [<ffffffff81038991>] ? select_task_rq_fair+0x511/0x780
<4>[ 7290.415578]  [<ffffffff8102e475>] __bad_area_nosemaphore+0x125/0x1e0
<4>[ 7290.415597]  [<ffffffff81038d0c>] ? __enqueue_entity+0x7c/0x80
<4>[ 7290.415616]  [<ffffffff81039201>] ? enqueue_task_fair+0x111/0x150
<4>[ 7290.415636]  [<ffffffff8102e53e>] bad_area_nosemaphore+0xe/0x10
<4>[ 7290.415656]  [<ffffffff8102e8fa>] do_page_fault+0x26a/0x320
<4>[ 7290.415674]  [<ffffffff813905df>] page_fault+0x1f/0x30
<4>[ 7290.415697]  [<ffffffffa0dd53a1>] ? iwl3945_rx_reply_tx+0xc1/0x450 [iwl3945]
<4>[ 7290.415723]  [<ffffffffa0dc8c47>] iwl3945_irq_tasklet+0x657/0x1740 [iwl3945]
<4>[ 7290.415746]  [<ffffffff8138fc60>] ? _spin_unlock+0x30/0x60
<4>[ 7290.415764]  [<ffffffff81049a21>] tasklet_action+0x101/0x110
<4>[ 7290.415783]  [<ffffffff8104a3d0>] __do_softirq+0xc0/0x160
<4>[ 7290.415801]  [<ffffffff8100d01c>] call_softirq+0x1c/0x30
<4>[ 7290.415818]  [<ffffffff8100eff5>] do_softirq+0x75/0xb0
<4>[ 7290.415835]  [<ffffffff81049ee5>] irq_exit+0x95/0xa0
<4>[ 7290.415852]  [<ffffffff8100e547>] do_IRQ+0x77/0xf0
<4>[ 7290.415869]  [<ffffffff8100c7d3>] ret_from_intr+0x0/0xf
<4>[ 7290.415883]  <EOI>  [<ffffffff81234efa>] ? acpi_idle_enter_bm+0x270/0x2a5
<4>[ 7290.415911]  [<ffffffff81234f04>] ? acpi_idle_enter_bm+0x27a/0x2a5
<4>[ 7290.415931]  [<ffffffff81234efa>] ? acpi_idle_enter_bm+0x270/0x2a5
<4>[ 7290.415952]  [<ffffffff812c11f3>] ? cpuidle_idle_call+0x93/0xf0
<4>[ 7290.415971]  [<ffffffff8100b0d7>] ? cpu_idle+0xa7/0x110
<4>[ 7290.415989]  [<ffffffff8137b3d5>] ? rest_init+0x75/0x80
<4>[ 7290.416007]  [<ffffffff8158cd0a>] ? start_kernel+0x3a7/0x3b3
<4>[ 7290.416026]  [<ffffffff8158c315>] ? x86_64_start_reservations+0x125/0x129
<4>[ 7290.416047]  [<ffffffff8158c3fd>] ? x86_64_start_kernel+0xe4/0xeb
Reported-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Tested-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Recent powersaving work resulted in power management ops being called
during EEPROM initialization. The lock used by these functions is not
initialized at this time. Ensure lock is initialized before it is used.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

we see from http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2125
that power saving does not work well on 3945. Since then power saving has
also been connected with association problems where an AP deathenticates a
3945 after it is unable to transmit data to it - this happens when 3945
enters power savings mode.

Disable power save support until issues are resolved.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I've also for a long time had a problem with the
temperature calculation code, which I had fixed
by byte-swapping the values, and now it turns out
that was the correct fix after all.

Also, any use of iwl_eeprom_query_addr() that is
for more than a u8 must be cast to little endian,
and some structs as well.

Fix all this. Again, no real impact on platforms
that already are little endian.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The construct "le16_to_cpu((__force __le16)(r >> 16))" has
always bothered me when looking through the iwlwifi code,
it shouldn't be necessary to __force anything, and before
this code, "r" was obtained with an ioread32, which swaps
each of the two u16 values in it properly when swapping the
entire u32 value. I've had arguments about this code with
people before, but always conceded they were right because
removing it only made things not work at all on big endian
platforms.

However, analysing a failure of the OTP reading code, I now
finally figured out what is going on, and why my intuition
about that code being wrong was right all along.

It turns out that the 'priv->eeprom' u8 array really wants
to have the data in it in little endian. So the force code
above and all really converts *to* little endian, not from
it. Cf., for instance, the function iwl_eeprom_query16() --
it reads two u8 values and combines them into a u16, in a
little-endian way. And considering it more, it makes sense
to have the eeprom array as on the device, after all not
all values really are 16-bit values, the MAC address for
instance is not.

Now, what this really means is that all the annotations are
completely wrong. The eeprom reading code should fill the
priv->eeprom array as a __le16 array, with __le16 values.

This also means that iwl_read_otp_word() should really have
a __le16 pointer as the data argument, since it should be
filling that in a format suitable for priv->eeprom.

Propagating these changes throughout, iwl_find_otp_image()
is found to be, now obviously visible, defective -- it uses
the data returned by iwl_read_otp_word() directly as if it
was CPU endianness. Fixing that, which is this hunk of the
patch:

-               next_link_addr = link_value * sizeof(u16);
+               next_link_addr = le16_to_cpu(link_value) * sizeof(u16);

is the only real change of this patch. Everything else is
just fixing the sparse annotations.

Also, the bug only shows up on big endian platforms with a
1000 series card. 5000 and previous series do not use OTP,
and 6000 series has shadow RAM support which means we don't
ever use the defective code on any cards but 1000.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We've had many reports of rt61pci failures with powersaving enabled.
Therefore, as a stop-gap measure, disable powersaving of the rt61pci
until we have found a proper solution.
Also disable powersaving on rt2800pci as it most probably will show
the same problem.

Cc: stable@kernel.org
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

sizeof(iv16) and sizeof(iv32) are the sizes of pointers.  Change them to
the size of the copied data.

Furthermore, iveiv_entry is a local structure that has just been
initialized and is not visible outside this function.  Thus, there would
seem to be no point to copy data into it.  The order of the arguments is
thus changed to copy the data into the parameters, which are provided as
pointers, suggesting in this case that they should be used to return values.

A simplified version of the semantic patch that finds the first problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression *x;
expression f;
type T;
@@

*f(...,(T)x,...)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

First, we copy/paste the padding stuff from ath9k_tx to ath_tx_cabq since it
needs to same kind of padding, but for internally generated beacons.
Next, software padding done on TX needs to be removed before calling
ieee80211_tx_status. The code was already there in ath_tx_complete but it
was wrong. Fix it by using ath9k_cmn_padpos. This later code has been
tested by sending packets to a monitor interface and reading packets from the
same interface.
Signed-off-by: NBenoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When trigger event log dumping from debugfs, the entire event log
should be dumped and the size should match the number of events being
dump.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Recent commits "iwlwifi: remove power-wasting calls to apm_ops.init()" and
"iwlagn: power up device before initializing EEPROM" had the goal of
reducing device power consumption from the time the module is loaded until
the interface is brought up and the device's power saving mechanisms kick
in. The idea is that once the module is loaded there is no need for the
device to consume power until the interface is brought up.

With the current solution the device is only powered up during EEPROM read,
and then so also only if the EEPROM type is OTP. We have found that on
certain platforms even non-OTP devices require power to be up during EEPROM
read. On these platforms the driver never loads and the system log contains
the following:

iwlagn 0000:03:00.0: MAC is in deep sleep!.  CSR_GP_CNTRL = 0x080403D8

We thus now power up all devices during EEPROM read.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In iwlwifi, priv->alloc_rxb_page is used to keep track of the Rx
pages allocated by the driver. This cleans up the page free routines
by introducing __iwl_free_pages/iwl_free_pages so that the accounting
is more accurate and less error prone. This also fixes two instances where
the counter was not updated.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a definition of the amount of TX headroom reserved by mac80211 itself
for its own purposes. Also add BUILD_BUG_ON to validate the value.
This define can then be used by drivers to request additional TX headroom
in the most efficient manner.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2800lib incorrectly detected whether RT2800USB was enabled because
it didn't account for a modularized RT2800USB driver.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update "US" and "JP" for current rules, and replace "EU" rules with the
world roaming domain (since it was only a pseudo-domain anyway).
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch ("mac80211: Use correct sign for mesh active path
refresh.") was actually a bug.  Reverted it and improved the
explanation of how mesh path refresh works.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Paths to mesh portals were being timed out immediately after each use in
intermediate forwarding nodes.  mppath->exp_time is set to the expiration time
so assigning it to jiffies was marking the path as expired.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Memset should be given the size of the structure, not the size of the pointer.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
type T;
T *x;
expression E;
@@

memset(x, E, sizeof(
+ *
 x))
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As shown in Kernel Bugzilla #14761, doing a controller restart after a
fatal DMA error does not accomplish anything other than consume the CPU
on an affected system. Accordingly, substitute a meaningful message for
the restart.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>        [2.6.32]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Michael Buesch reports that his rtl8187 gives warnings on suspend
("queueing ieee80211 work while going to suspend" warnings), as rtl8187
can call ieee80211_queue_delayed_work after mac80211 is suspended.

This change enhances rtl8187 led code so we can avoid queuing work after
mac80211 is suspended: now we register a radio led and make additional
checks to ensure led is off/on properly as mac80211 wants.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Without this we have no gaurantee of the integrity of the
EEPROM and are likely to encounter a lot of bogus bug reports
due to actual issues on the EEPROM. With the EEPROM checksum
check in place we can easily rule those issues out.

If you run patch during a revert *you* have a card with a busted
EEPROM and only older kernel will support that concoction. This
patch is a trade off between not accepitng bogus EEPROMs and
avoiding bogus bug reports allowing developers to focus instead
on real concrete issues.

If stable keeps bogus bug reports because of a possibly busted EEPROM
feel free to apply this there too.

Tested on an AR5414

Cc: stable@kernel.org
Cc: jirislaby@gmail.com
Cc: akpm@linux-foundation.org
Cc: rjw@sisk.pl
Cc: me@bobcopeland.com
Cc: david.quan@atheros.com
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This part was missed in "cfg80211: implement get_wireless_stats",
probably because sta_set_sinfo already existed and was only handling
dBm signals.

Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the current_bss is not set, 'iwconfig <iface> key off' does not
clear the private flag. Hence after we connect with WEP to an AP and
then try to connect with another non-WEP AP, it does not work.
This issue will not be seen if supplicant is used.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

commit 46ceb60c ("gianfar: Add
Multiple group Support") introduced the following build error
with CONFIG_NET_POLL_CONTROLLER=y:

  CC      ggianfar.o
ggianfar.c: In function 'gfar_netpoll':
ggianfar.c:2653: error: invalid storage class for function 'gfar_interrupt'
ggianfar.c:2652: warning: ISO C90 forbids mixed declarations and code
ggianfar.c:2681: error: invalid storage class for function 'adjust_link'
ggianfar.c:2764: error: invalid storage class for function 'gfar_set_multi'
ggianfar.c:2855: error: invalid storage class for function 'gfar_clear_exact_match'
ggianfar.c:2877: error: invalid storage class for function 'gfar_set_hash_for_addr'
ggianfar.c:2898: error: invalid storage class for function 'gfar_set_mac_for_addr'
ggianfar.c:2922: error: invalid storage class for function 'gfar_error'
ggianfar.c:3020: warning: ISO C90 forbids mixed declarations and code
ggianfar.c:3032: error: invalid storage class for function 'gfar_init'
ggianfar.c:3037: error: invalid storage class for function 'gfar_exit'
ggianfar.c:3041: error: initializer element is not constant
ggianfar.c:3042: error: initializer element is not constant
ggianfar.c:3042: warning: ISO C90 forbids mixed declarations and code
ggianfar.c:3042: error: expected declaration or statement at end of input
make[1]: *** [ggianfar.o] Error 1

This patch fixes the issue.
Reported-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

About 50% of shutdowns of b44 Ethernet adapter ends by kernel panic
with kernels compiled with stack-protector.

Checking b44_magic_pattern() return values, one call of
b44_magic_pattern() returns 127. It means, that set_bit(128, pmask)
was called on line 1509. It means that bit 0 of 17th byte of pmask was
overwritten. But pmask has only 16 bytes. Stack corruption happens.
 
It seems that set_bit() on line 1509 always writes one bit off.

The fix does not only solve the stack corruption, but also makes Wake
On LAN working on my onboard B44 on Asus A7V-333X mainboard.

It seems that this problem affects all kernel versions since commit
725ad800 ([PATCH] b44: add wol for old nic) on 2006-06-20.
Signed-off-by: NStanislav Brabec <sbrabec@suse.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It can happen, that tcp_retransmit_skb fails due to some error.
In such cases we might end up into a state where tp->retrans_out
is zero but that's only because we removed the TCPCB_SACKED_RETRANS
bit from a segment but couldn't retransmit it because of the error
that happened. Therefore some assumptions that retrans_out checks
are based do not necessarily hold, as there still can be an old
retransmission but that is only visible in TCPCB_EVER_RETRANS bit.
As retransmission happen in sequential order (except for some very
rare corner cases), it's enough to check the head skb for that bit.

Main reason for all this complexity is the fact that connection dying
time now depends on the validity of the retrans_stamp, in particular,
that successive retransmissions of a segment must not advance
retrans_stamp under any conditions. It seems after quick thinking that
this has relatively low impact as eventually TCP will go into CA_Loss
and either use the existing check for !retrans_stamp case or send a
retransmission successfully, setting a new base time for the dying
timer (can happen only once). At worst, the dying time will be
approximately the double of the intented time. In addition,
tcp_packet_delayed() will return wrong result (has some cc aspects
but due to rarity of these errors, it's hardly an issue).

One of retrans_stamp clearing happens indirectly through first going
into CA_Open state and then a later ACK lets the clearing to happen.
Thus tcp_try_keep_open has to be modified too.

Thanks to Damian Lukowski <damian@tvk.rwth-aachen.de> for hinting
that this possibility exists (though the particular case discussed
didn't after all have it happening but was just a debug patch
artifact).
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves retransmits_timed_out() from include/net/tcp.h
to tcp_timer.c, where it is used.
Reported-by: NFrederic Leroy <fredo@starox.org>
Signed-off-by: NDamian Lukowski <damian@tvk.rwth-aachen.de>
Acked-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a problem in the TCP connection timeout calculation.
Currently, timeout decisions are made on the basis of the current
tcp_time_stamp and retrans_stamp, which is usually set at the first
retransmission.
However, if the retransmission fails in tcp_retransmit_skb(),
retrans_stamp is not updated and remains zero. This leads to wrong
decisions in retransmits_timed_out() if tcp_time_stamp is larger than
the specified timeout, which is very likely.
In this case, the TCP connection dies after the first attempted
(and unsuccessful) retransmission.

With this patch, tcp_skb_cb->when is used instead, when retrans_stamp
is not available.

This bug has been introduced together with retransmits_timed_out() in
2.6.32, as the number of retransmissions has been used for timeout
decisions before. The corresponding commit was
6fa12c85 (Revert Backoff [v3]:
Calculate TCP's connection close threshold as a time value.).

Thanks to Ilpo Järvinen for code suggestions and Frederic Leroy for
testing.
Reported-by: NFrederic Leroy <fredo@starox.org>
Signed-off-by: NDamian Lukowski <damian@tvk.rwth-aachen.de>
Acked-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use common_task instead of reset_task and link_chg_task, so it fix "call cancel_work_sync
from the work itself".
Signed-off-by: NJie Yang <jie.yang@atheros.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add pci map direction in atl1c_buffer flags, it is used when call pci_unmap
apis.
Signed-off-by: NJie Yang <jie.yang@atheros.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unified firmware image may not contain MN type of firmware.
Driver should fall back to NOMN firmware type instead
of going to flash.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o netif_running() check for enabling interrupt at end of napi poll is
  not enough to cover firmwar recovery. Instead test __NX_DEV_UP bit.
o Avoid re-entry into to netxen_nic_down() with __NX_DEV_UP bit check.
Acked-by: NDhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o To prevent race conditions with other reset events.
  During suspend/resume and firmware recovery, acquire rtnl_lock,
  while changing interface state.
Acked-by: NDhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>