Default behavior is to use the information from the upper IO stacks to
select the hardware queue to use for IO submission.  Which typically has
good cpu affinity.

However, the driver, when used on some variants of the upstream kernel, has
found queuing information to be suboptimal for FCP or IO completion locked
on particular cpus.

For command submission situations, the lpfc_fcp_io_sched module parameter
can be set to specify a hardware queue selection policy that overrides the
os stack information.

For IO completion situations, rather than queing cq processing based on the
cpu servicing the interrupting event, schedule the cq processing on the cpu
associated with the hardware queue's cq.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The XRI get/put lists were partitioned per hardware queue. However, the
adapter rarely had sufficient resources to give a large number of resources
per queue. As such, it became common for a cpu to encounter a lack of XRI
resource and request the upper io stack to retry after returning a BUSY
condition. This occurred even though other cpus were idle and not using
their resources.

Create as efficient a scheme as possible to move resources to the cpus that
need them. Each cpu maintains a small private pool which it allocates from
for io. There is a watermark that the cpu attempts to keep in the private
pool.  The private pool, when empty, pulls from a global pool from the
cpu. When the cpu's global pool is empty it will pull from other cpu's
global pool. As there many cpu global pools (1 per cpu or hardware queue
count) and as each cpu selects what cpu to pull from at different rates and
at different times, it creates a radomizing effect that minimizes the
number of cpu's that will contend with each other when the steal XRI's from
another cpu's global pool.

On io completion, a cpu will push the XRI back on to its private pool.  A
watermark level is maintained for the private pool such that when it is
exceeded it will move XRI's to the CPU global pool so that other cpu's may
allocate them.

On NVME, as heartbeat commands are critical to get placed on the wire, a
single expedite pool is maintained. When a heartbeat is to be sent, it will
allocate an XRI from the expedite pool rather than the normal cpu
private/global pools. On any io completion, if a reduction in the expedite
pools is seen, it will be replenished before the XRI is placed on the cpu
private pool.

Statistics are added to aid understanding the XRI levels on each cpu and
their behaviors.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Now that the lower half has much better per-cpu parallelization using the
hardware queues, the SCSI MQ support needs to be tied into it.

The involves the following mods:

 - Use the hardware queue info from the midlayer to help select the
   hardware queue to utilize. This required change to the get_scsi-buf_xxx
   routines.

 - Remove lpfc_sli4_scmd_to_wqidx_distr() routine. No longer needed.

 - Includes fix for SLI-3 that does not have multi queue parallelization.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

SLI4 nvme functions are passing the SLI3 ring number when posting wqe to
hardware. This should be indicating the hardware queue to use, not the ring
number.

Replace ring number with the hardware queue that should be used.

Note: SCSI avoided this issue as it utilized an older lfpc_issue_iocb
routine that properly adapts.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Many io statistics were being sampled and saved using adapter-based data
structures. This was creating a lot of contention and cache thrashing in
the I/O path.

Move the statistics to the hardware queue data structures.  Given the
per-queue data structures, use of atomic types is lessened.

Add new sysfs and debugfs stat routines to collate the per hardware queue
values and report at an adapter level.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Similar to the io execution path that reports cpu context information, the
debugfs routines for cpu information needs to be aligned with new hardware
queue implementation.

Convert debugfs cnd nvme cpucheck statistics to report information per
Hardware Queue.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Both NVME and SCSI aborts are now processed off the CQ workqueue and do not
generate events for the slowpath any more.

Remove the unused event code.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Once the IO buff allocations were made shared, there was a single XRI
buffer list shared by all hardware queues.  A single list isn't great for
performance when shared across the per-cpu hardware queues.

Create a separate XRI IO buffer get/put list for each Hardware Queue.  As
SGLs and associated IO buffers get allocated/posted to the firmware; round
robin their assignment across all available hardware Queues so that there
is an equitable assignment.

Modify SCSI and NVME IO submit code paths to use the Hardware Queue logic
for XRI allocation.

Add a debugfs interface to display hardware queue statistics

Added new empty_io_bufs counter to track if a cpu runs out of XRIs.

Replace common_ variables/names with io_ to make meanings clearer.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently, both nvme and fcp each have their own concept of an io_channel,
which is a combination wq/cq and associated msix.  Different cpus would
share an io_channel.

The driver is now moving to per-cpu wq/cq pairs and msix vectors.  The
driver will still use separate wq/cq pairs per protocol on each cpu, but
the protocols will share the msix vector.

Given the elimination of the nvme and fcp io channels, the module
parameters will be removed.  A new parameter, lpfc_hdw_queue is added which
allows the wq/cq pair allocation per cpu to be overridden and allocated to
lesser value. If lpfc_hdw_queue is zero, the number of pairs allocated will
be based on the number of cpus. If non-zero, the parameter specifies the
number of queues to allocate. At this time, the maximum non-zero value is
64.

To manage this new paradigm, a new hardware queue structure is created to
track queue activity and relationships.

As MSIX vector allocation must be known before setting up the
relationships, msix allocation now occurs before queue datastructures are
allocated. If the number of vectors allocated is less than the desired
hardware queues, the hardware queue counts will be reduced to the number of
vectors
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There is a extra queue and msix vector for expresslane. Now that the driver
will be doing queues per cpu, this oddball queue is no longer needed.
Expresslane will utilize the normal per-cpu queues.

Updated debugfs sli4 queue output to go along with the change
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently, both NVME and SCSI get their IO buffers from separate
pools. XRI's are associated 1:1 with IO buffers, so XRI's are also split
between protocols.

Eliminate the independent pools and use a single pool. Each buffer
structure now has a common section and a protocol section. Per protocol
routines for SGL initialization are removed and replaced by common
routines. Initialization of the buffers is only done on the common area.
All other fields, which are protocol specific, are initialized when the
buffer is allocated for use in the per-protocol allocation routine.

In the past, the SCSI side allocated IO buffers as part of slave_alloc
calls until the maximum XRIs for SCSI was reached. As all XRIs are now
common and may be used for either protocol, allocation for everything is
done as part of adapter initialization and the scsi side has no action in
slave alloc.

As XRI's are no longer split, the lpfc_xri_split module parameter is
removed.

Adapters based on SLI3 will continue to use the older scsi_buf_list_get/put
routines.  All SLI4 adapters utilize the new IO buffer scheme
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

lpfc_nvme_prep_io_cmd() checks for null pnode, but caller
lpfc_nvme_fcp_io_submit() has already ensured it's non-null.

Remove the pnode null check.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

An hba-wide lock is taken in the nvme io completion routine. The lock
covers null'ing of the nrport pointer in the cmd structure.

The nrport member isn't necessary. After extracting the pointer from the
command, the pointer was dereferenced to get the fc discovery node
pointer. But the fc discovery node pointer is alrady in the command
structure so the dereferrence was unnecessary.

Eliminated the nrport structure member and its use, which also eliminates
the port-wide lock.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch removes unnecessary code to handle RSCN, instead performs full
scan everytime driver receives RSCN

Fixes: d4f7a16a ("scsi: qla2xxx: Remove ASYNC GIDPN switch command")
Cc: stable@vger.kernel.org #4.19
Signed-off-by: NQuinn Tran <qtran@marvell.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For eh_bus_reset, driver is supposed to reset the link.  Current option to
reset the link is applicable to Loop only. This patch updates current FW
option with the one that is applicable to all topologies.
Signed-off-by: NQuinn Tran <qtran@marvell.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When loop was made down explicitly due to cable pull, then for N2N toplogy,
if FAWWPN BIT is enabled by user, then it would restore some default
(garbage) value for Physical port WWPN, so this show garbage WWPN for the
port. Fix is, to restore physical port WWPN, if it is fabric
configuration. When loop is explicitly made down, and FAWWPN feature is
enabled, then driver need to restore original flashed WWPN.
Signed-off-by: NSawan Chandak <schandak@marvell.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch fixes memory leak by releasing DMA memory in case CT request and
response allocation fails.
Signed-off-by: NQuinn Tran <qtran@marvall.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch fixes SRB allocation flag from GFP_KERNEL to GFP_ATOMIC, to
prevent sleeping in IRQ context
Signed-off-by: NGiridhar Malavali <gmalavali@marvell.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch flushes del_work and free_work while sending NACK response for
PRLI
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch allocates DMA memory to prevent NULL pointer access for ct_sns
request while sending switch commands.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

On Transmit respond in target mode, if the chip is already reset or the
session is already deleted, then advance the command to the free step.
There is no need to abort the command, because the chip has already flushed
it.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

On session cleanup, either an implicit LOGO or an implicit PRLO is used to
flush IOs.  If the flush command hit Queue Full condition, then it is
dropped.  This patch adds retry code to prevent command drop.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Change default ZIO threshold to an optimized value.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch provide call back functions to stop the chip and resume the chip
if the PCI lower level driver wants to perform function level reset/FLR.
Before the FLR, the chip will be stopped to turn off all DMA activity.
After the FLR, the chip is reset to resume previous operation state.
Signed-off-by: NQuinn Tran <qtran@marvell.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch fixes the issue where Dell-EMC Target will fail to discover LUNs
if domain and area of port ID is not same as adapter's.
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Unused now, and another field in struct request bites the dust.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

No users left.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

No more need in a blk-mq world where the scsi command and request are
allocated together.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

No real need for bidi support once the OSD code is gone.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Now that all the users are gone the SCSI OSD library can be removed as
well.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This was an example for using the SCSI OSD protocol, which we're trying
to remove.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

We can just stash away the second request in struct bsg_job instead of
using the block layer req->next_rq field, allowing for the eventual removal
of the latter.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Move all actual functionality into helpers, just leaving the dispatch in
this function.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBenjamin Block <bblock@linux.ibm.com>
Tested-by: NBenjamin Block <bblock@linux.ibm.com>
Tested-by: NAvri Altman <avri.altman@wdc.com>
Acked-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Updated driver version to 27.102.00.00 from 27.101.00.00.
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add Atlas PCIe Switch Management Port device PNPID,
Vendor Id: 0x1000
device Id: 0x00B2

This device is based on MPI 2.6 spec and it exposes one SES device to
accept management commands for the PCIe switch.
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added device ID for NVMe Switch Adapter (Ambrosia).
VID: 0x1000
DID: 0x02B1
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

MPI Endpoint is a PCIe switch based on MPI2.

Renaming device ID macro from MPI2_MFGPAGE_DEVID_SAS2308_MPI_EP to
MPI2_MFGPAGE_DEVID_SWITCH_MPI_EP.
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adds support for the new DEVICE_LIST DCMD.

Driver currently sends two separate DCMDs for getting the list of PDs and
LDs that are exposed to host.  The new DCMD provides a single interface to
get a list of both PDs and LDs that are exposed to the host.  Based on the
list of target IDs that are returned by this DCMD, driver will add the
devices (PD/LD) to SML.  Driver will check for FW support for this new DCMD
and based on the support will either send the new DCMD or will fall back to
the earlier method of sending two separate DCMDs for PD and LD list.
Signed-off-by: NKashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: NShivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In preparation of adding support for the DEVICE_LIST DCMD, this patch
refactors the code in the AEN event handling path.  Add new function to
update the PD and LD list in driver.  Move the code to scan PD and VD
channels into separate function.
Signed-off-by: NShivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>