Prior to commit fbd929f2
	bonding: support QinQ for bond arp interval

the arp monitoring code allowed for proper detection of devices
stacked on top of vlans.  Since the above commit, the
code can still detect a device stacked on top of single
vlan, but not a device stacked on top of Q-in-Q configuration.
The search will only set the inner vlan tag if the route
device is the vlan device.  However, this is not always the
case, as it is possible to extend the stacked configuration.

With this patch it is possible to provision devices on
top Q-in-Q vlan configuration that should be used as
a source of ARP monitoring information.

For example:
ip link add link bond0 vlan10 type vlan proto 802.1q id 10
ip link add link vlan10 vlan100 type vlan proto 802.1q id 100
ip link add link vlan100 type macvlan

Note:  This patch limites the number of stacked VLANs to 2,
just like before.  The original, however had another issue
in that if we had more then 2 levels of VLANs, we would end
up generating incorrectly tagged traffic.  This is no longer
possible.

Fixes: fbd929f2 (bonding: support QinQ for bond arp interval)
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@redhat.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: Patric McHardy <kaber@trash.net>
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vlad Yasevich says:

====================
Fix lockdep issues with stacked devices

Recent commit dc8eaaa0
    vlan: Fix lockdep warning when vlan dev handle notification

attempted to solve lockdep issues with vlans where multiple
vlans were stacked.  However, the code does not work correctly
when the vlan stack is interspersed with other devices in between
the vlans.  Additionally, similar lockdep issues show up with other
devices.

This series provides a generic way to solve these issue for any
devices that can be stacked.  It also addresses the concern for
vlan and macvlan devices.  I am not sure whether it makes sense
to do so for other types like team, vxlan, and bond.

Thanks
-vlad

Since v2:
  - Remove rcu variants from patch1, since that function is called
    only under rtnl.
  - Fix whitespace problems reported by checkpatch

Since v1:
  - Fixed up a goofed-up rebase.
    * is_vlan_dev() should be bool and that change belongs in patch3.
    * patch4 should not have any vlan changes in it.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Macvlan devices try to avoid stacking, but that's not always
successfull or even desired.  As an example, the following
configuration is perefectly legal and valid:

eth0 <--- macvlan0 <---- vlan0.10 <--- macvlan1

However, this configuration produces the following lockdep
trace:
[  115.620418] ======================================================
[  115.620477] [ INFO: possible circular locking dependency detected ]
[  115.620516] 3.15.0-rc1+ #24 Not tainted
[  115.620540] -------------------------------------------------------
[  115.620577] ip/1704 is trying to acquire lock:
[  115.620604]  (&vlan_netdev_addr_lock_key/1){+.....}, at: [<ffffffff815df49c>] dev_uc_sync+0x3c/0x80
[  115.620686]
but task is already holding lock:
[  115.620723]  (&macvlan_netdev_addr_lock_key){+.....}, at: [<ffffffff815da5be>] dev_set_rx_mode+0x1e/0x40
[  115.620795]
which lock already depends on the new lock.

[  115.620853]
the existing dependency chain (in reverse order) is:
[  115.620894]
-> #1 (&macvlan_netdev_addr_lock_key){+.....}:
[  115.620935]        [<ffffffff810d57f2>] lock_acquire+0xa2/0x130
[  115.620974]        [<ffffffff816f62e7>] _raw_spin_lock_nested+0x37/0x50
[  115.621019]        [<ffffffffa07296c3>] vlan_dev_set_rx_mode+0x53/0x110 [8021q]
[  115.621066]        [<ffffffff815da557>] __dev_set_rx_mode+0x57/0xa0
[  115.621105]        [<ffffffff815da5c6>] dev_set_rx_mode+0x26/0x40
[  115.621143]        [<ffffffff815da6be>] __dev_open+0xde/0x140
[  115.621174]        [<ffffffff815da9ad>] __dev_change_flags+0x9d/0x170
[  115.621174]        [<ffffffff815daaa9>] dev_change_flags+0x29/0x60
[  115.621174]        [<ffffffff815e7f11>] do_setlink+0x321/0x9a0
[  115.621174]        [<ffffffff815ea59f>] rtnl_newlink+0x51f/0x730
[  115.621174]        [<ffffffff815e6e75>] rtnetlink_rcv_msg+0x95/0x250
[  115.621174]        [<ffffffff81608b19>] netlink_rcv_skb+0xa9/0xc0
[  115.621174]        [<ffffffff815e6dca>] rtnetlink_rcv+0x2a/0x40
[  115.621174]        [<ffffffff81608150>] netlink_unicast+0xf0/0x1c0
[  115.621174]        [<ffffffff8160851f>] netlink_sendmsg+0x2ff/0x740
[  115.621174]        [<ffffffff815bc9db>] sock_sendmsg+0x8b/0xc0
[  115.621174]        [<ffffffff815bd4b9>] ___sys_sendmsg+0x369/0x380
[  115.621174]        [<ffffffff815bdbb2>] __sys_sendmsg+0x42/0x80
[  115.621174]        [<ffffffff815bdc02>] SyS_sendmsg+0x12/0x20
[  115.621174]        [<ffffffff816ffd69>] system_call_fastpath+0x16/0x1b
[  115.621174]
-> #0 (&vlan_netdev_addr_lock_key/1){+.....}:
[  115.621174]        [<ffffffff810d4d43>] __lock_acquire+0x1773/0x1a60
[  115.621174]        [<ffffffff810d57f2>] lock_acquire+0xa2/0x130
[  115.621174]        [<ffffffff816f62e7>] _raw_spin_lock_nested+0x37/0x50
[  115.621174]        [<ffffffff815df49c>] dev_uc_sync+0x3c/0x80
[  115.621174]        [<ffffffffa0696d2a>] macvlan_set_mac_lists+0xca/0x110 [macvlan]
[  115.621174]        [<ffffffff815da557>] __dev_set_rx_mode+0x57/0xa0
[  115.621174]        [<ffffffff815da5c6>] dev_set_rx_mode+0x26/0x40
[  115.621174]        [<ffffffff815da6be>] __dev_open+0xde/0x140
[  115.621174]        [<ffffffff815da9ad>] __dev_change_flags+0x9d/0x170
[  115.621174]        [<ffffffff815daaa9>] dev_change_flags+0x29/0x60
[  115.621174]        [<ffffffff815e7f11>] do_setlink+0x321/0x9a0
[  115.621174]        [<ffffffff815ea59f>] rtnl_newlink+0x51f/0x730
[  115.621174]        [<ffffffff815e6e75>] rtnetlink_rcv_msg+0x95/0x250
[  115.621174]        [<ffffffff81608b19>] netlink_rcv_skb+0xa9/0xc0
[  115.621174]        [<ffffffff815e6dca>] rtnetlink_rcv+0x2a/0x40
[  115.621174]        [<ffffffff81608150>] netlink_unicast+0xf0/0x1c0
[  115.621174]        [<ffffffff8160851f>] netlink_sendmsg+0x2ff/0x740
[  115.621174]        [<ffffffff815bc9db>] sock_sendmsg+0x8b/0xc0
[  115.621174]        [<ffffffff815bd4b9>] ___sys_sendmsg+0x369/0x380
[  115.621174]        [<ffffffff815bdbb2>] __sys_sendmsg+0x42/0x80
[  115.621174]        [<ffffffff815bdc02>] SyS_sendmsg+0x12/0x20
[  115.621174]        [<ffffffff816ffd69>] system_call_fastpath+0x16/0x1b
[  115.621174]
other info that might help us debug this:

[  115.621174]  Possible unsafe locking scenario:

[  115.621174]        CPU0                    CPU1
[  115.621174]        ----                    ----
[  115.621174]   lock(&macvlan_netdev_addr_lock_key);
[  115.621174]                                lock(&vlan_netdev_addr_lock_key/1);
[  115.621174]                                lock(&macvlan_netdev_addr_lock_key);
[  115.621174]   lock(&vlan_netdev_addr_lock_key/1);
[  115.621174]
 *** DEADLOCK ***

[  115.621174] 2 locks held by ip/1704:
[  115.621174]  #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff815e6dbb>] rtnetlink_rcv+0x1b/0x40
[  115.621174]  #1:  (&macvlan_netdev_addr_lock_key){+.....}, at: [<ffffffff815da5be>] dev_set_rx_mode+0x1e/0x40
[  115.621174]
stack backtrace:
[  115.621174] CPU: 3 PID: 1704 Comm: ip Not tainted 3.15.0-rc1+ #24
[  115.621174] Hardware name: Hewlett-Packard HP xw8400 Workstation/0A08h, BIOS 786D5 v02.38 10/25/2010
[  115.621174]  ffffffff82339ae0 ffff880465f79568 ffffffff816ee20c ffffffff82339ae0
[  115.621174]  ffff880465f795a8 ffffffff816e9e1b ffff880465f79600 ffff880465b019c8
[  115.621174]  0000000000000001 0000000000000002 ffff880465b019c8 ffff880465b01230
[  115.621174] Call Trace:
[  115.621174]  [<ffffffff816ee20c>] dump_stack+0x4d/0x66
[  115.621174]  [<ffffffff816e9e1b>] print_circular_bug+0x200/0x20e
[  115.621174]  [<ffffffff810d4d43>] __lock_acquire+0x1773/0x1a60
[  115.621174]  [<ffffffff810d3172>] ? trace_hardirqs_on_caller+0xb2/0x1d0
[  115.621174]  [<ffffffff810d57f2>] lock_acquire+0xa2/0x130
[  115.621174]  [<ffffffff815df49c>] ? dev_uc_sync+0x3c/0x80
[  115.621174]  [<ffffffff816f62e7>] _raw_spin_lock_nested+0x37/0x50
[  115.621174]  [<ffffffff815df49c>] ? dev_uc_sync+0x3c/0x80
[  115.621174]  [<ffffffff815df49c>] dev_uc_sync+0x3c/0x80
[  115.621174]  [<ffffffffa0696d2a>] macvlan_set_mac_lists+0xca/0x110 [macvlan]
[  115.621174]  [<ffffffff815da557>] __dev_set_rx_mode+0x57/0xa0
[  115.621174]  [<ffffffff815da5c6>] dev_set_rx_mode+0x26/0x40
[  115.621174]  [<ffffffff815da6be>] __dev_open+0xde/0x140
[  115.621174]  [<ffffffff815da9ad>] __dev_change_flags+0x9d/0x170
[  115.621174]  [<ffffffff815daaa9>] dev_change_flags+0x29/0x60
[  115.621174]  [<ffffffff811e1db1>] ? mem_cgroup_bad_page_check+0x21/0x30
[  115.621174]  [<ffffffff815e7f11>] do_setlink+0x321/0x9a0
[  115.621174]  [<ffffffff810d394c>] ? __lock_acquire+0x37c/0x1a60
[  115.621174]  [<ffffffff815ea59f>] rtnl_newlink+0x51f/0x730
[  115.621174]  [<ffffffff815ea169>] ? rtnl_newlink+0xe9/0x730
[  115.621174]  [<ffffffff815e6e75>] rtnetlink_rcv_msg+0x95/0x250
[  115.621174]  [<ffffffff810d329d>] ? trace_hardirqs_on+0xd/0x10
[  115.621174]  [<ffffffff815e6dbb>] ? rtnetlink_rcv+0x1b/0x40
[  115.621174]  [<ffffffff815e6de0>] ? rtnetlink_rcv+0x40/0x40
[  115.621174]  [<ffffffff81608b19>] netlink_rcv_skb+0xa9/0xc0
[  115.621174]  [<ffffffff815e6dca>] rtnetlink_rcv+0x2a/0x40
[  115.621174]  [<ffffffff81608150>] netlink_unicast+0xf0/0x1c0
[  115.621174]  [<ffffffff8160851f>] netlink_sendmsg+0x2ff/0x740
[  115.621174]  [<ffffffff815bc9db>] sock_sendmsg+0x8b/0xc0
[  115.621174]  [<ffffffff8119d4af>] ? might_fault+0x5f/0xb0
[  115.621174]  [<ffffffff8119d4f8>] ? might_fault+0xa8/0xb0
[  115.621174]  [<ffffffff8119d4af>] ? might_fault+0x5f/0xb0
[  115.621174]  [<ffffffff815cb51e>] ? verify_iovec+0x5e/0xe0
[  115.621174]  [<ffffffff815bd4b9>] ___sys_sendmsg+0x369/0x380
[  115.621174]  [<ffffffff816faa0d>] ? __do_page_fault+0x11d/0x570
[  115.621174]  [<ffffffff810cfe9f>] ? up_read+0x1f/0x40
[  115.621174]  [<ffffffff816fab04>] ? __do_page_fault+0x214/0x570
[  115.621174]  [<ffffffff8120a10b>] ? mntput_no_expire+0x6b/0x1c0
[  115.621174]  [<ffffffff8120a0b7>] ? mntput_no_expire+0x17/0x1c0
[  115.621174]  [<ffffffff8120a284>] ? mntput+0x24/0x40
[  115.621174]  [<ffffffff815bdbb2>] __sys_sendmsg+0x42/0x80
[  115.621174]  [<ffffffff815bdc02>] SyS_sendmsg+0x12/0x20
[  115.621174]  [<ffffffff816ffd69>] system_call_fastpath+0x16/0x1b

Fix this by correctly providing macvlan lockdep class.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit dc8eaaa0.
	vlan: Fix lockdep warning when vlan dev handle notification

Instead we use the new new API to find the lock subclass of
our vlan device.  This way we can support configurations where
vlans are interspersed with other devices:
  bond -> vlan -> macvlan -> vlan
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently netif_addr_lock_nested assumes that there can be only
a single nesting level between 2 devices.  However, if we
have multiple devices of the same type stacked, this fails.
For example:
 eth0 <-- vlan0.10 <-- vlan0.10.20

A more complicated configuration may stack more then one type of
device in different order.
Ex:
  eth0 <-- vlan0.10 <-- macvlan0 <-- vlan1.10.20 <-- macvlan1

This patch adds an ndo_* function that allows each stackable
device to report its nesting level.  If the device doesn't
provide this function default subclass of 1 is used.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Multiple devices in the kernel can be stacked/nested and they
need to know their nesting level for the purposes of lockdep.
This patch provides a generic function that determines a nesting
level of a particular device by its type (ex: vlan, macvlan, etc).
We only care about nesting of the same type of devices.

For example:
  eth0 <- vlan0.10 <- macvlan0 <- vlan1.20

The nesting level of vlan1.20 would be 1, since there is another vlan
in the stack under it.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Starting from linux-3.13, GRO attempts to build full size skbs.

Problem is the commit assumed one particular field in skb->cb[]
was clean, but it is not the case on some stacked devices.

Timo reported a crash in case traffic is decrypted before
reaching a GRE device.

Fix this by initializing NAPI_GRO_CB(skb)->last at the right place,
this also removes one conditional.

Thanks a lot to Timo for providing full reports and bisecting this.

Fixes: 8a29111c ("net: gro: allow to build full sized skb")
Bisected-by: NTimo Teras <timo.teras@iki.fi>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Tested-by: NTimo Teräs <timo.teras@iki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The connected check fails to check for ip_gre nbma mode tunnels
properly. ip_gre creates temporary tnl_params with daddr specified
to pass-in the actual target on per-packet basis from neighbor
layer. Detect these tunnels by inspecting the actual tunnel
configuration.

Minimal test case:
 ip route add 192.168.1.1/32 via 10.0.0.1
 ip route add 192.168.1.2/32 via 10.0.0.2
 ip tunnel add nbma0 mode gre key 1 tos c0
 ip addr add 172.17.0.0/16 dev nbma0
 ip link set nbma0 up
 ip neigh add 172.17.0.1 lladdr 192.168.1.1 dev nbma0
 ip neigh add 172.17.0.2 lladdr 192.168.1.2 dev nbma0
 ping 172.17.0.1
 ping 172.17.0.2

The second ping should be going to 192.168.1.2 and head 10.0.0.2;
but cached gre tunnel level route is used and it's actually going
to 192.168.1.1 via 10.0.0.1.

The lladdr's need to go to separate dst for the bug to trigger.
Test case uses separate route entries, but this can also happen
when the route entry is same: if there is a nexthop exception or
the GRE tunnel is IPsec'ed in which case the dst points to xfrm
bundle unique to the gre lladdr.

Fixes: 7d442fab ("ipv4: Cache dst in tunnels")
Signed-off-by: NTimo Teräs <timo.teras@iki.fi>
Cc: Tom Herbert <therbert@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding more than one chip on device-tree currently causes the probing
routine to always use the first chips data pointer.
Signed-off-by: NFabian Godehardt <fg@emlix.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, "ip -6 route get mark xyz" ignores the mark passed in
by userspace. Make it honour the mark, just like IPv4 does.
Signed-off-by: NLorenzo Colitti <lorenzo@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Include changes:
- fix NULL dereference in batadv_orig_hardif_seq_print_text()
- fix reference counting imbalance when using fragmentation
- avoid access to orig_node objects after they have been free'd
- fix local TT check for outgoing arp requests in DAT

When the NAPI budget was not all used, xenvif_poll() would call
napi_complete() /after/ enabling the interrupt.  This resulted in a
race between the napi_complete() and the napi_schedule() in the
interrupt handler.  The use of local_irq_save/restore() avoided by
race iff the handler is running on the same CPU but not if it was
running on a different CPU.

Fix this properly by calling napi_complete() before reenabling
interrupts (in the xenvif_napi_schedule_or_enable_irq() call).
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Acked-by: NWei Liu <wei.liu2@citrix.com>
Acked-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

John W. Linville says:

====================
pull request: wireless 2014-05-15

Please pull this batch of fixes for the 3.15 stream...

For the mac80211 bits, Johannes says:

"One fix is to get better VHT performance and the other fixes tracing
garbage or other potential issues with the interface name tracing."

And...

"This has a fix from Emmanuel for a problem I failed to fix - when
association is in progress then it needs to be cancelled while
suspending (I had fixed the same for authentication). Also included a
fix from myself for a userspace API problem that hit the iw tool and a
fix to the remain-on-channel framework."

For the iwlwifi bits, Emmanuel says:

"Alex fixes the scan by disabling the fragmented scan. David prevents
scan offload while associated, the firmware seems not to like it. I
fix a stupid bug I made in BT Coex, and fix a bad #ifdef clause in rate
scaling.  Along with that there is a fix for a NULL pointer exception
that can happen if we load the driver and our ISR gets called because
the interrupt line is shared. The fix has been tested by the reporter."

And...

"We have here a fix from David Spinadel that makes a previous fix more
complete, and an off-by-one issue fixed by Eliad in the same area.
I fix the monitor that broke on the way."

Beyond that...

Daniel Kim's one-liner fixes a brcmfmac regression caused by a typo
in an earlier commit..

Rajkumar Manoharan fixes an ath9k oops reported by David Herrmann.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There may be padding on the ticket contained in the key payload, so just ensure
that the claimed token length is large enough, rather than exactly the right
size.
Signed-off-by: NNathaniel Wesley Filardo <nwf@cs.jhu.edu>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With commit be9dad1f ("net: phy: suspend phydev when going
to HALTED"), an unused PHY device will be put in a low-power mode
using BMCR_PDOWN. Some Ethernet drivers might be calling phy_start()
and phy_stop() from ndo_open and ndo_close() respectively, while
calling phy_connect() and phy_disconnect() from probe and remove.
In such a case, the PHY will be powered down during the phy_stop()
call, but will fail to be powered up in phy_start().
This patch fixes this scenario.
Signed-off-by: NJiancheng Xue <xuejiancheng@huawei.com>
Signed-off-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4: Fix VF MAC address change under RoCE usage

This short series provides proper handling for the case where a
VF netdevice change their MAC address under a RoCE use case. The code
it deals with was introduced in 3.15-rc1

Prior to this series the source MAC used for the VM RoCE CM
packets remains as before the MAC modification. Hence RoCE CM
packets sent by the VF will not carry the same source MAC
address as the non-CM packets.

Earlier 3.15-rc commit f24f790f "net/mlx4_core: Load the Eth driver
first" handled just one instance of the problem, but this one
provides a more generic and proper solution which covers all
cases of VF mac change.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we receive a netdev event indicating a netdev change and/or
a netdev address change, we must change the MAC index used by the
proxy QP1 (in the QP context), otherwise RoCE CM packets sent by the
VF will not carry the same source MAC address as the non-CM packets.

We use the UPDATE_QP command to perform this change.

In order to avoid modifying a QP context based on netdev event,
while the driver attempts to destroy this QP (e.g either the mlx4_ib
or ib_mad modules are unloaded), we use mutex locking in both flows.

Since the relevant mlx4 proxy GSI QP is created indirectly by the
mad module when they create their GSI QP, the mlx4 didn't need to
keep track on that QP prior to this change.

Now, when QP modifications are needed to this QP from within the
driver, we added refernece to it.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds UPDATE_QP SRIOV wrapper support.

The mechanism is a general one, but currently only source MAC
index changes are allowed for VFs.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I've missed to add a NULL entry to the bond_intmax_tbl when I introduced
it with the conversion of arp_interval so add it now.

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>

Fixes: 7bdb04ed ("bonding: convert arp_interval to use the new option API")
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Acked-by: NVeaceslav Falico <vfalico@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original series for reintroducing grant mapping for netback had a patch [1]
to handle receiving of packets from an another VIF. Grant copy on the receiving
side needs the grant ref of the page to set up the op.
The original patch assumed (wrongly) that the frags array haven't changed. In
the case reported by Sander, the sending guest sent a packet where the linear
buffer and the first frag were under PKT_PROT_LEN (=128) bytes.
xenvif_tx_submit() then pulled up the linear area to 128 bytes, and ditched the
first frag. The receiving side had an off-by-one problem when gathered the grant
refs.
This patch fixes that by checking whether the actual frag's page pointer is the
same as the page in the original frag list. It can handle any kind of changes on
the original frags array, like:
- removing granted frags from the array at any point
- adding local pages to the frags list anywhere
- reordering the frags
It's optimized to the most common case, when there is 1:1 relation between the
frags and the list, plus works optimal when frags are removed from the end or
the beginning.

[1]: 3e2234: xen-netback: Handle foreign mapped pages on the guest RX path
Reported-by: NSander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: NZoltan Kiss <zoltan.kiss@citrix.com>
Acked-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFC 4861 states in 7.2.5:

	The IsRouter flag in the cache entry MUST be set based on the
         Router flag in the received advertisement.  In those cases
         where the IsRouter flag changes from TRUE to FALSE as a result
         of this update, the node MUST remove that router from the
         Default Router List and update the Destination Cache entries
         for all destinations using that neighbor as a router as
         specified in Section 7.3.3.  This is needed to detect when a
         node that is used as a router stops forwarding packets due to
         being configured as a host.

Currently, when dealing with NA Message which IsRouter flag changes from
TRUE to FALSE, the kernel only removes router from the Default Router List,
and don't update the Destination Cache entries.

Now in order to update those Destination Cache entries, i introduce
function rt6_clean_tohost().
Signed-off-by: NDuan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	net/ipv4/ip_vti.c

Steffen Klassert says:

====================
pull request (net): ipsec 2014-05-15

This pull request has a merge conflict in net/ipv4/ip_vti.c
between commit 8d89dcdf ("vti: don't allow to add the same
tunnel twice") and commit a3245236  ("vti4:Don't count header
length twice"). It can be solved like it is done in linux-next.

1) Fix a ipv6 xfrm output crash when a packet is rerouted
   by netfilter to not use IPsec.

2) vti4 counts some header lengths twice leading to an incorrect
   device mtu. Fix this by counting these headers only once.

3) We don't catch the case if an unsupported protocol is submitted
   to the xfrm protocol handlers, this can lead to NULL pointer
   dereferences. Fix this by adding the appropriate checks.

4) vti6 may unregister pernet ops twice on init errors.
   Fix this by removing one of the calls to do it only once.
   From Mathias Krause.

5) Set the vti tunnel mark before doing a lookup in the error
   handlers. Otherwise we don't find the correct xfrm state.
====================

The conflict in ip_vti.c was simple, 'net' had a commit
removing a line from vti_tunnel_init() and this tree
being merged had a commit adding a line to the same
location.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the call to phy_init_hw failed in phy_attach_direct, phy_detach is called
to detach the phy device from its network device. If the attached driver is a
generic phy driver, this also detaches the driver. Subsequently phy_resume
is called, which assumes without checking that a driver is attached to the
device. This will result in a crash such as

Unable to handle kernel paging request for data at address 0xffffffffffffff90
Faulting instruction address: 0xc0000000003a0e18
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c0000000003a0e18] .phy_attach_direct+0x68/0x17c
LR [c0000000003a0e6c] .phy_attach_direct+0xbc/0x17c
Call Trace:
[c0000003fc0475d0] [c0000000003a0e6c] .phy_attach_direct+0xbc/0x17c (unreliable)
[c0000003fc047670] [c0000000003a0ff8] .phy_connect_direct+0x28/0x98
[c0000003fc047700] [c0000000003f0074] .of_phy_connect+0x4c/0xa4

Only call phy_resume if phy_init_hw was successful.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vince Bridgers says:

====================
Altera TSE: Fix Sparse errors and misc issues

This is version 2 of a patch series to correct sparse errors, cppcheck
warnings, and workaound a multicast filtering issue in the Altera TSE
Ethernet driver. Multicast filtering is not working as expected, so if
present in the hardware will not be used and promiscuous mode enabled
instead. This workaround will be replaced with a working solution when
completely debugged, integrated and tested.

Version 2 is different from the first submission by breaking out the
workaround as a seperate patch and addressing a few structure instance
declarations by making them const per review comments.

If you find this patch acceptable, please consider this for inclusion into
the Altera TSE driver source code.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch disables multicast hash filtering if present in the hardware
and uses promiscuous mode instead until the problem with multicast
filtering has been debugged, integrated and tested.
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the many sparse errors and warnings contained in the
initial submission of the Altera Triple Speed Ethernet driver, and a
few minor cppcheck warnings. Changes are tested on ARM and NIOS2
example designs, and compile tested against multiple architectures.
Typical issues addressed were as follows:

altera_tse_ethtool.c:136:19: warning: incorrect type in argument
    1 (different address spaces)
altera_tse_ethtool.c:136:19:    expected void const volatile
    [noderef] <asn:2>*addr
altera_tse_ethtool.c:136:19:    got unsigned int *<noident>
...
altera_sgdma.c:129:31: warning: cast removes address space of
    expression
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Cong Wang <cwang@twopensource.com>

commit 50624c93 (net: Delay default_device_exit_batch until no
devices are unregistering) introduced rtnl_lock_unregistering() for
default_device_exit_batch(). Same race could happen we when rmmod a driver
which calls rtnl_link_unregister() as we call dev->destructor without rtnl
lock.

For long term, I think we should clean up the mess of netdev_run_todo()
and net namespce exit code.

Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NCong Wang <cwang@twopensource.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change introduced by 88e48d7b
("batman-adv: make DAT drop ARP requests targeting local clients")
implements a check that prevents DAT from using the caching
mechanism when the client that is supposed to provide a reply
to an arp request is local.

However change brought by be1db4f6
("batman-adv: make the Distributed ARP Table vlan aware")
has not converted the above check into its vlan aware version
thus making it useless when the local client is behind a vlan.

Fix the behaviour by properly specifying the vlan when
checking for a client being local or not.
Reported-by: NSimon Wunderlich <simon@open-mesh.com>
Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>

A pointer to the orig_node representing a bat-gateway is
stored in the gw_node->orig_node member, but the refcount
for such orig_node is never increased.
This leads to memory faults when gw_node->orig_node is accessed
and the originator has already been freed.

Fix this by increasing the refcount on gw_node creation
and decreasing it on gw_node free.
Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>

In the new fragmentation code the batadv_frag_send_packet()
function obtains a reference to the primary_if, but it does
not release it upon return.

This reference imbalance prevents the primary_if (and then
the related netdevice) to be properly released on shut down.

Fix this by releasing the primary_if in batadv_frag_send_packet().

Introduced by ee75ed88
("batman-adv: Fragment and send skbs larger than mtu")

Cc: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Acked-by: NMartin Hundebøll <martin@hundeboll.net>

If hard_iface is NULL and goto out is made batadv_hardif_free_ref()
doesn't check for NULL before dereferencing it to get to refcount.

Introduced in cb1c92ec
("batman-adv: add debugfs support to view multiif tables").
Reported-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Acked-by: NAntonio Quartulli <antonio@meshcoding.com>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

This is the s390 variant of Alexei's JIT bug fix.
(patch description below stolen from Alexei's patch)

bpf_alloc_binary() adds 128 bytes of room to JITed program image
and rounds it up to the nearest page size. If image size is close
to page size (like 4000), it is rounded to two pages:
round_up(4000 + 4 + 128) == 8192
then 'hole' is computed as 8192 - (4000 + 4) = 4188
If prandom_u32() % hole selects a number >= PAGE_SIZE - sizeof(*header)
then kernel will crash during bpf_jit_free():

kernel BUG at arch/x86/mm/pageattr.c:887!
Call Trace:
 [<ffffffff81037285>] change_page_attr_set_clr+0x135/0x460
 [<ffffffff81694cc0>] ? _raw_spin_unlock_irq+0x30/0x50
 [<ffffffff810378ff>] set_memory_rw+0x2f/0x40
 [<ffffffffa01a0d8d>] bpf_jit_free_deferred+0x2d/0x60
 [<ffffffff8106bf98>] process_one_work+0x1d8/0x6a0
 [<ffffffff8106bf38>] ? process_one_work+0x178/0x6a0
 [<ffffffff8106c90c>] worker_thread+0x11c/0x370

since bpf_jit_free() does:
  unsigned long addr = (unsigned long)fp->bpf_func & PAGE_MASK;
  struct bpf_binary_header *header = (void *)addr;
to compute start address of 'bpf_binary_header'
and header->pages will pass junk to:
  set_memory_rw(addr, header->pages);

Fix it by making sure that &header->image[prandom_u32() % hole] and &header
are in the same page.

Fixes: aa2d2c73 ("s390/bpf,jit: address randomize and write protect jit code")
Reported-by: NAlexei Starovoitov <ast@plumgrid.com>
Cc: <stable@vger.kernel.org> # v3.11+
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During remain on channel request, ANI worker thread is not stopped
before doing hw reset. This is causing kernel crash in
hw_per_calibration. This change ensures that ANI is stopped before
doing chip reset and it will be rescheduled later when the chip is
configured back to home channel and having valid bss.
Reported-by: NDavid Herrmann <dh.herrmann@gmail.com>
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When sending data through IUCV a MESSAGE COMPLETE interrupt
signals that sent data memory can be freed or reused again.
With commit f9c41a62
"af_iucv: fix recvmsg by replacing skb_pull() function" the
MESSAGE COMPLETE callback iucv_callback_txdone() identifies
the wrong skb as being confirmed, which leads to data corruption.
This patch fixes the skb mapping logic in iucv_callback_txdone().
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some BE3 FW versions, after a HW reset, interrupts will remain disabled
for each function. So, explicitly enable the interrupts in the eeh_resume
handler, else after an eeh recovery interrupts wouldn't work.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In my recent fix (76a691d0: fix dma unmap warning), Ben Hutchings noted that my
loop count was incorrect.  Where j started at startidx, it should have started
at zero, and gone on for count entries, not to endidx.  Additionally, a DMA
resource exhaustion should drop the frame and (for now), return
NETDEV_TX_OK, not NETEV_TX_BUSY.  This patch fixes both of those issues:
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: Ben Hutchings <ben@decadent.org.uk>
CC: "David S. Miller" <davem@davemloft.net>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jouni reported that if a remain-on-channel was active on the
same channel as the current operating channel, then the ROC
would start, but any frames transmitted using mgmt-tx on the
same channel would get delayed until after the ROC.

The reason for this is that the ROC starts, but doesn't have
any handling for "remain on the same channel", so it stops
the interface queues. The later mgmt-tx then puts the frame
on the interface queues (since it's on the current operating
channel) and thus they get delayed until after the ROC.

To fix this, add some logic to handle remaining on the same
channel specially and not stop the queues etc. in this case.
This not only fixes the bug but also improves behaviour in
this case as data frames etc. can continue to flow.

Cc: stable@vger.kernel.org
Reported-by: NJouni Malinen <j@w1.fi>
Tested-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

tot_len does specify the size of struct ipv6_txoptions. We need opt_flen +
opt_nflen to calculate the overall length of additional ipv6 extensions.

I found this while auditing the ipv6 output path for a memory corruption
reported by Alexey Preobrazhensky while he fuzzed an instrumented
AddressSanitizer kernel with trinity. This may or may not be the cause
of the original bug.

Fixes: 4df98e76 ("ipv6: pmtudisc setting not respected with UFO/CORK")
Reported-by: NAlexey Preobrazhensky <preobr@google.com>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>