Add PHY IRQ pin definition for AT91SAM9260-EK board.
Signed-off-by: NWojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Removed the infinite loop in our arch_reset().

After calling arch_reset(), the kernel waits for 1 second before
printing a "reboot failed" message and then waits for ever itself.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Added MAINTAINERS entry for the Atmel AT91RM9200.
Accept (some) responsibility...
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Updated some of the comments in the atmel_serial.h header detailing
which bits are only available on the AT91RM9200 or the AT91SAM9xx
processors.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The USB Device port registers are already defined in
drivers/usb/gadget/at91_udc.h.  This file can therefore just be removed.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

1. The CPU identification has moved from <system.h> to <cpu.h>.

2. AT91RM9200_BASE_US0 is only defined if we are compiling in support
for the AT91RM9200.  Therefore we need to replace the CONFIG_ARM ifdef
with CONFIG_ARCH_AT91RM9200
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Replace the 'is_b' variable with 'slot_b' in at91_mmc_data.
Also add the new 'chipselect' variable for CF/PCMCIA and 'bus_width_16'
variable for NAND.

This (and previous patches) will unfortunately break the current MMC,
USB Gadget and PCMCIA drivers.  Updates and fixes for those drivers will
be submitted to the various subsystem maintainers.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch contains various updates the at91rm9200_devices.c file:
      * Consistent naming of resources and platform_devices.
      * PCMCIA/Compact Flash: Configuration of the memory controller
        moved out of the driver and into this file.
      * MMC: Enable the VCC pin (if one is configured)
      * MMC: Enable the internal pullups on the I/O pins.
      * NAND: Configuration of the memory controller moved out of the
        driver and into this file.
      * Added TWI/I2C resources.
      * The names of some of the CONFIG_ variables were changed.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

A number of configuration file changes.

These are mainly to replace references to ARCH_AT91RM9200 and
ARCH_AT91SAM9261 with the common/generic ARCH_AT91.  That way we don't
need to mention every specific AT91 processor explicitly.

Also adds the configuration option for AT91SAM9260-EK and AT91SAM9261-EK
boards.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds support for the Atmel AT91SAM9261-EK board.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds support for the Atmel AT91SAM9260-EK board.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch includes a number of small changes for integrating the
AT91SAM9261 and AT91SAM0260 support.

      * Can only select support for one AT91 processor at a time.
      * Remove most of the remaining static memory mapping for the
        AT91RM9200.
      * Reserve 1Mb of memory below the IO for mapping the internal SRAM
        and any custom board-specific devices (ie, FPGA).
      * The SAM9260 has more serial ports, so increase the maximum to 7.
      * Define the standard chipselect addresses, and define other
        addresses relative to those.
      * CLOCK_TICK_RATE is different on the SAM926x's.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The bits used to select the USB clocks are different on the SAM9's.
Add support for the HCK clocks on the AT91SAM9261.

Patch from Patrice Vilchez & Nicolas Ferre
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch converts the old CONFIG_MTD_PHYSMAP_ options to the new
physmap API by creating a physmap platform device for the NOR flash
found on the Atmel AT91RM9200-DK and AT91RM9200-EK boards.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch updates the Carmeva board support:
      * Specify the MMC Write-protect and Detection pins.
      * Add configuration of SPI devices.

Patch from Peer Georgi.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Attached is a patch for at91rm9200_time.c which removes
the 'BUG: soft lockup detected on CPU#0!' message when
exiting suspended states.

Patch from Savin Zlobec
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch includes the pin initialization, resource definition and
registration of the platform_devices for the SAM9260 and SAM9261
processors.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for the timer on the Atmel AT91SAM9261 and AT91SAM9260
processors.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds definitions for the new peripherals integrated in the
AT91SAM9260 and AT91SAM9261 processors:  ECC, LCD, RSTC, RTT, SHDWC,
WDT, MATRIX, SDRAMC, SMC.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch updates the drivers (and other files) which include the
hardware headers.  This fixes the breakage introduced in patches 3950/1
and 3951/1 (those patches were getting big).

The AVR32 architecture uses the same serial driver and had its own copy
of at91rm9200_pdc.h.  Renamed it to at91_pdc.h
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Most of the AT91RM9200 user peripherals are also integrated into the
Atmel SAM9 range of processors.  This patch renames the headers from
at91rm9200_xx.h to at91_xx.h to indicate they're not
at91rm9200-specific.

The new SAM9-specific registers and register bits have also been
defined.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The AT91RM9200 system header file (at91rm9200_sys.h) has been split into
separate header files for each peripheral.  This was necessary since
some of the system peripherals are also used on AT91SAM9260 and
AT91SAM9261.

The new SAM9-specific register bits have also been defined.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds the initial support for the newer Atmel AT91SAM9261 and
AT91SAM9260 processors.  The code is based on, and makes use of, the
existing AT91RM9200 support.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch replaces the arch_identify() in system.h with a set of
cpu_is_XXX() macro's.  This allows for compile-time checking of the
target AT91 processor.

Original patch from David Brownell.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The external interrupt sources are different on the various AT91
processors.  This patch introduces the global 'at91_extern_irq' variable
that contains a bitset of the available external interrupt sources.

The processor reset mechanism also differs on the various AT91
processors.  This patch also adds a global 'at91_arch_reset' callback
(from system.h) into the processor-specific code to perform the reset.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch renames the arch/arm/mach-at91rm9200/devices.c file to
at91rm9200_devices.c.  The file contains AT91RM9200-specific code, so we
will need separate files for the SAM9 processors.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

It's all good.

This changes the type of variable "i" in rtl8169_init_one()
from "unsigned int" to "int". "i" is checked for < 0 later,
which can never happen for "unsigned". This results in broken
error handling.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 3943/1: share declaration of struct pxa2xx_udc_mach_info between multiple platforms
  [ARM] Export smp_call_function()
  [ARM] Add PM_LEGACY defaults

Move declaration of struct pxa2xx_udc_mach_info from
include/asm-arm/arch-pxa/udc.h to new file
include/asm-arm/mach/udc_pxa2xx.h.

This allow us to use this structure with
multiple platforms - pxa and ixp4xx. USB
device controller used in pxa25x is the same
as controller used in ixp4xx.
Signed-off-by: NMilan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Otherwise CPU 0 doesn't show up in sysfs which breaks some software.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [NET]: Fix MAX_HEADER setting.
  [NETFILTER]: ipt_REJECT: fix memory corruption
  [NETFILTER]: conntrack: fix refcount leak when finding expectation
  [NETFILTER]: ctnetlink: fix reference count leak
  [NETFILTER]: nf_conntrack: fix the race on assign helper to new conntrack
  [NETFILTER]: nfctnetlink: assign helper to newly created conntrack

MAX_HEADER is either set to LL_MAX_HEADER or LL_MAX_HEADER + 48, and
this is controlled by a set of CONFIG_* ifdef tests.

It is trying to use LL_MAX_HEADER + 48 when any of the tunnels are
enabled which set hard_header_len like this:

dev->hard_header_len = LL_MAX_HEADER + sizeof(struct xxx);

The correct set of tunnel drivers which do this are:

ipip
ip_gre
ip6_tunnel
sit

so make the ifdef test match.

Noticed by Patrick McHardy and with help from Herbert Xu.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On devices with hard_header_len > LL_MAX_HEADER ip_route_me_harder()
reallocates the skb, leading to memory corruption when using the stale
tcph pointer to update the checksum.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All users of __{ip,nf}_conntrack_expect_find() don't expect that
it increments the reference count of expectation.
Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When NFA_NEST exceeds the skb size the protocol reference is leaked.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The found helper cannot be assigned to conntrack after unlocking
nf_conntrack_lock. This tries to find helper to assign again.
Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes the bug which doesn't assign helper to newly created
conntrack via nf_conntrack_netlink.
Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [PATCH] libata: Fixup ata_sas_queuecmd to handle __ata_scsi_queuecmd failure
  [PATCH] ahci: AHCI mode SATA patch for Intel ICH9
  [PATCH] libata: don't schedule EH on wcache on/off if old EH

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
  selinux: fix dentry_open() error check