Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mwl8k's ->prepare_multicast() currently just enables reception of
all multicast packets, which is somewhat ineffective.

Fix this by either disabling all multicast RX, enabling multicast
RX according to the multicast address filter table, or enabling all
multicast RX, depending on whether ->prepare_multicast() was given
any multicast addresses and whether the hardware multicast address
filter table is large enough to fit all requested addresses.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Minor changes to the transmit quiescing logic:
- Clarify the locking rules for ->tx_wait: only the holder of fw_mutex
  can wait for the TX path to become idle, but tx_wait itself is read
  and cleared by the TX reclaim tasklet under tx_lock.
- Inline mwl8k_txq_busy() in its callers.
- There's no need to kick the transmitter again in
  mwl8k_tx_wait_empty(), since it will have been kicked when the
  packets currently in the TX ring were added to it.
- If the TX ring didn't drain in time, run mwl8k_scan_tx_ring() after
  reading priv->pending_pkts without dropping tx_lock in between.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The GET_STAT command doesn't have an 'action' field like other
commands do, so remove it.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

wl1271_main.c:(.text+0x271052): undefined reference to `unregister_inetaddr_notifier'
wl1271_main.c:(.text+0x2714d7): undefined reference to `register_inetaddr_notifier'

Driver is doing some filtering based on IP addresses...
Acked-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Responses to firmware commands are read in by the command transmission
function, as part of command flow. Previously responses were read in
multiple places.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Correct the endianness-handling of the firmware command result status handling
code.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

PSM entries can fail (transmitting the corresponding null-func may not
be heard by the AP.) Previously, this scenario was not detected, and
out-of-sync between STA and AP could occur.

Add retry implementation for the entries to recover from the situation.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Check the result code of all commands, and return an error code if the
firmware reports an error in execution. Previously this error would go
ignored in most cases.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, to avoid distortions, the TX power level has been hardcoded
to a low value. The value is slightly too low for good functionality, so
we increase it from 7dB to 12dB.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The null-data template (nullfunc) is dependent on the BSSID of the
current AP only, so it needs to be updated only when the BSSID changes.

Removed excess setting of the template.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently it is possible to request a scan on only
disabled channels, which could be problematic for
some drivers. Reject such scans, and also ignore
disabled channels that are given. This resuls in
the scan begin/end event only including channels
that are actually used.

This makes the mac80211 check for disabled channels
superfluous. At the same time, remove the no-IBSS
check from mac80211 -- nothing says that we should
not find any networks on channels that cannot be
used for an IBSS, even when operating in IBSS mode.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Report successful transmissions (receiver awake and on the same
channel) by generating ACK frames on the hwsim0 interface. This makes
it easier to figure out from packet capture logs whether frames were
delivered or not.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Track the idle state for hwsim radios and reject TX if mac80211 is
trying to transmit something when the radio is supposed to be idle. In
addition, do not deliver frames if the receiving radio is in the idle
state.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Neither of these commands should clear the current configuration value
if they return error. Furthermore, cfg80211_set_cipher_group() should
be able to handle IW_AUTH_CIPHER_NONE without reporting error.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

James Grossmann [1] reported that p54 spews out confusing
messages instead of preventing the mayhem from happening.

the reason is that "p54: generate channel list dynamically"
is not perfect. It didn't discard incomplete channel data
sets and therefore p54 advertised to support them as well.

[1]: http://marc.info/?l=linux-wireless&m=125699830215890

Cc: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: NJames Grossmann <cctsurf@gmail.com>
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since sometimes mac80211 queues up a scan request
to only act on it later, it must be allowed to
(internally) cancel a not-yet-running scan, e.g.
when the interface is taken down. This condition
was missing since we always checked only the
local->scanning variable which isn't yet set in
that situation.
Reported-by: NLuis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For 6x50 series, it is wimax/wifi combo device, so driver need to enable
the wimax/wifi co-exist function and send the coexist event priority
table to uCode for operation.

The priority table will be used by uCode to determine what is the proper
action it should take when co-exist with WiMAX.
For example, when WiFi runs a scan, it must own radio exclusively, therefore
will disconnect WiMAX if WiMAX is connected.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Spatial Multiplexing Power Save was disabled to achieve better
throughput while in power save mode by activating all the rx chains all the time.
By doing so, the device power consumption is high.

Enable static/dynamic spatial multiplexing power save if device support
it, which can lower the power consumption without impact throughput.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add data structure define for COEX_MEDIUM_NOTIFICATION and
COEX_EVENT_CMD host commands.

COEX_MEDIUM_NOTIFICATION is notification from uCode to host to indicate
medium changes. COEX_EVENT_CMD is from host to uCode for coex event
request.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

More information than the "-EIO" return code will be useful here.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fits better in how the callbacks operate (alloc does allocation and
init does initialization). This also helps if we later want to do our own
initialization without relying on the mac80211 allocation.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently the rate scale information is pointed to from the mac80211
station structure but since that is the only member we might as well make
it part of the structure. Also move the rate scaling initialization to the
init function, no need to do it when we allocate the structure. This fits
with how mac80211 deals with rate scaling information (it always calls init
after allocation) and makes it easier for us to later call initialization
directly.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In preparation for some station management changes we split the addition of
a broadcast station from the other stations. Later we will rely on mac80211
to direct all management (addition/removal) of all stations except the
broadcast station.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since iwlagn is the only user of these functions, move it to this module.
This results in a bit more code moving than just these functions since the
functions only used by them are also moved and we need to export the
symbols previously available to them directly.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Handling responses to driver originated commands include passing the
original command buffer to the caller. At this time it is possible for a
callback to be invoked that is passed this command buffer and thus likely
to access it.

We need to make sure that the memory associated with that buffer is not DMA
mapped at the time.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Wakeup interrupt has been updating write pointers (indexes, actually) only
for tx queues 0-5.  This is adequate just for 3945, but inadequate for other
devices, all of which have more tx queues.  Now updating all tx/command queues,
so device can be aware of all new tx and host commands enqueued while
device was asleep.

This can potentially improve data traffic bandwidth and/or latency.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add/clarify comments and debug messages for interrupt used only for uCode load
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Invoke workaround to avoid instability in L0->L0S->L1 transition on PCIe bus.
Workaround disables L0S state so device moves directly from L0->L1.
Workaround needed on all devices since and including 4965; add to 6000/1000.

Describe bug and workaround better in comments.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To save power, don't run apm_ops.init() until needed at "up" time.

EEPROM (5000 and earlier devices) may be read without running apm_ops.init(),
but OTP reads (6000 and newer devices) require a powered-up chip.
Therefore, remove apm_ops.init() from the general path in XXXX_pci_probe(),
and call it only if device uses OTP.  Once done with OTP read, call
apm_ops.stop() to reset chip and save power until "up" time comes around.

NOTE:  This patch depends on removal of priv->lock from iwl_apm_stop();
lock does not get initialized until later in flow.  See patch
"remove unneeded locks from apm_stop()".
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since priv->reg_lock was added to keep multi-access register manipulation
atomic, priv->lock protection is no longer needed.  Remove this from
iwl_apm_stop_master() and iwl_apm_stop().

Add warning of timeout when polling for busmaster disablement confirmation,
and some comments.

NOTE:  This is needed to enable use of apm_ops.stop() within iwl_eeprom_init();
priv->lock does not get initialized until after this flow.  See patch
"remove power-wasting calls to apm_ops.init()"
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By setting the firmware version in wiphy it is possible to obtain this
information via ethtool. Some examples,

	    # ethtool -i wlan1
	    driver: iwlagn
	    version: 2.6.32-rc5-wl-56840-g26d8540
	    firmware-version: 228.57.2.23
	    bus-info: 0000:03:00.0
	    # ethtool -i wlan0
	    driver: iwl3945
	    version: 2.6.32-rc5-wl-56840-g26d8540
	    firmware-version: 15.28.2.8
	    bus-info: 0000:02:00.0
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The multi-line code in this macro wasn't wrapped
in do {} while (0) so we cannot use it in an if()
branch safely in the future -- fix that.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes the internal command and data buffers that the GSPI driver
maintained and instead relies on the Libertas core to synchronize access
to the command and data ports as with the other interface drivers.  This
cleanup reduces the GSPI driver's memory footprint and should improve
performance by removing the need to copy to these internal buffers.
This also simplifies the bottom half of the interrupt handler.

This is an incremental cleanup: after removing the redundant buffers, we
can further improve the driver to use a threaded IRQ handler instead of
maintaining its own thread.  However I would like a few folks to test
the buffer removal first and make sure that I'm not introducing
regressions.

Tested on Blackfin BF527 with DMA disabled due to an issue with the SPI
host controller driver in the current bleeding-edge Blackfin kernel.  I
would appreciate it if someone with working DMA could test this patch
and provide feedback.
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Tested-by: NGeorge Shore <george.shore@imgtec.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch is adapted from the submission by Michael Buesch <mb@bu3sch.de>
for a bounce-buffer copying problem with b43.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's not right to do something here when returning an
error, and hostapd should never have relied on it as
it only fixes up a small part of the problem anyway.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This variable is set once, and tested once.
However, the code path that can set it is
mutually exclusive with the code path that
tests it, so the test is always true. Thus
we also don't need to set it either and can
just remove the variable.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We drop nullfunc frames, but not qos-nullfunc frames,
even though those could be used for PS state control
as well.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>