The clock-frequency values of the i2c controller nodes match the
defaults of the driver. Remove the properties to use the defaults,
and be consistent with sun8i.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

i2c0 is connected to the gsl1680 capacitive touch panel controller.
i2c1 is connected to an mma7660 3-axis accelerometer.
i2c2 is connected to the front and back gc0309 camera sensors.
The camera sensors require additional regulators be enabled before
they are available.

All these peripherals are not supported by the kernel yet.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add nodes for the 3 i2c controllers found on A23 SoCs to the sun8i DTSI.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This adds pin-muxing info for the i2c controller / port combinations
which are known to be used on actual boards.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The card detect pin setting was taken from the original fex file,
and is confirmed to work.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add nodes for the 3 mmc controllers found on A23 SoCs to the sun8i DTSI.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This adds pin-muxing info for the mmc controller / port combinations
which are known to be used on actual boards.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The MMC module clocks on sun8i are the same as those found on
previous Allwinner SoCs, module 0 clocks.

This patch adds the clocks nodes to the dtsi with existing drivers.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Now that we have R_PIO controller support and the pinmux for R_UART,
add the correct pinctrl properties to the R_UART node.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

R_UART is available on extra pads on certain tablets, which makes it
ideal for use as a console. Here we add the pins for it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

uart0 on sun8i is only muxed with mmc0, which makes it a poor choice
for the console. However, some tablets only have pads for uart0
available on the circuit board.

Here we add the uart0 pinmux set for people who need it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Now that we have a driver for the R_PIO controller,
add the corresponding device node to the dtsi.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Now that we have a driver for the sun8i PIO controller,
add the corresponding device node to the dtsi.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

All of our SPI controllers support DMA transfers, so let's add the
properties here so they can be used when it's best to do so.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
Reviewed-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

All of our SPI controllers support DMA transfers, so let's add the
properties here so they can be used when it's best to do so.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
Reviewed-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

All of our SPI controllers support DMA transfers, so let's add the
properties here so they can be used when it's best to do so.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
Reviewed-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A20 SoC has a sun4i-compatible DMA controller. Let's add a node to
represent it on the device tree.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
Reviewed-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A10S and A13 SoCs have sun4i-compatible DMA controllers. Let's add
the corresponding nodes to represent them on the device tree.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
Reviewed-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Let's add a node to represent the A10 DMA controller on the device tree.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
Reviewed-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Now that we have a driver for sun6i's rtc hardware, add a device node
for it so we can use it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

sun8i shares the same rtc hardware as sun6i. Now that we have a driver
for it, add a device node to the DTSI for it so we can use it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This was caused by commit 5a8da524 ("ARM: dts: exynos5420: add dsi
node"), which conflicted with d51cad7d ("ARM: dts: remove display
power domain for exynos5420").

The DTS addition should never have been merged through the DRM tree in
the first place, and it lacked an ack from the platform maintainer
(who would have known that the disp_pd reference got removed).
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The EHCI and HSIC device tree nodes were added in the wrong place.
Fix them.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKever Yang <kever.yang@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This patch adds common part of dsi node.
Signed-off-by: NYoungJun Cho <yj44.cho@samsung.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch adds mipi-phy node for MIPI DSI device.
Signed-off-by: NYoungJun Cho <yj44.cho@samsung.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch adds sysreg property to fimd device node
which is required to use I80 interface.
Signed-off-by: NYoungJun Cho <yj44.cho@samsung.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch adds sysreg property to fimd device node
which is required to use I80 interface.
Signed-off-by: NYoungJun Cho <yj44.cho@samsung.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch adds socfpga Ethernet filter attributes for multicast
and unicast filters per Synopsys Ethernet IP configuration chosen
by Altera for the Cyclone 5 and Arria SOC FPGAs.
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use CPU_METHOD_OF_DECLARE() instead. And declare smp method in dts file.

Changelog:
v6:
  * Use hisilicon,hi3620-smp as enable-method property in Hi3620 dts.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: NWei Xu <xuwei5@hisilicon.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add dts file for Hisilicon x5hd2 development kit board.
Signed-off-by: NHaifeng Yan <yanhaifeng@gmail.com>
Signed-off-by: NJiancheng Xue <jchxue@gmail.com>
Signed-off-by: NHaojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: NWei Xu <xuwei5@hisilicon.com>
[olof: Rename dts/dtsi to include hisi prefix]
Signed-off-by: NOlof Johansson <olof@lixom.net>

This is the top USB port on the evb (the one closest to the Ethernet
connector).
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKever Yang <kever.yang@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

rk3288 has two kind of usb controller; this adds the ehci variant for
host0 and hsic.

At the moment we don't add any phys for these controllers, but the
default settings seem to work OK.

There is a hardware problem in ohci controller which make it
unavailable and host0 controller can only support high-speed devices.
Signed-off-by: NKever Yang <kever.yang@rock-chips.com>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

There is no phy driver that works on the Rockchip board for either USB
host port yet.  For now just hardcode the vbus signal to be on all the
time which makes both the dwc2 host and the EHCI port work.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Working on sound support I noticed the Apalis T30 Evaluation board
device tree missing the more generic Apalis T30 compatible string.
Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Indentation of the clock property used a hodgepodge of tabs and spaces.
Make them more consistent (tabs for indentation followed by spaces for
alignment).
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The GPIO pin connected to card detect was inverted twice: once by
the argument to the GPIO line itself where it was magically marked
as active low by the flag GPIO_ACTIVE_LOW (0x01) in the third cell,
and also marked active low AGAIN by explicitly stating
"cd-inverted" (a deprecated method).

After commit 78f87df2
"mmc: mmci: Use the common mmc DT parser" this results in the
line being inverted twice so it was effectively uninverted, while
the old code would not have this effect, instead disregarding the
flag on the GPIO line altogether, which is a bug. I admit the
semantics may be unclear but inverting twice is as good a
definition as any on how this should work.

So fix up the buggy device tree. Use proper #includes so the DTS
is clear and readable.

Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This adds the Designware compatible watchdog found on RK3xxx Cortex-A9 SoCs.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

We set default pinctrl settings for the uarts in rk3188.dtsi already,
so remove forgotten duplicate.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

This patch add missing pinctrl for uart0/1 for Exynos3250. The gpio pin (
uart0_data, uart0_fctl, uart1_data) is only used for UART IP.
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch removes duplicat 'interrupt-parent' property for Exynos3250
because exynos3250.dtsi already defined 'interrupt-parent' property
as following:

In arch/arm/boot/dts/exynos3250.dtsi:

	compatible = "samsung,exynos3250";
	interrupt-parent = <&gic>;
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>