For !CONFIG_OF of_get_property() is defined to always return NULL. Thus
there's no need to protect the call to of_get_property() with #ifdef
CONFIG_OF.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The macro to write 64-bits quantities to the 32-bits register swapped
the value and offsets arguments, we want to preserve the ordering of the
arguments with respect to how writel() is implemented for instance:
value first, offset/base second.

Fixes: 246d7f77 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when the verifier log is enabled the print_bpf_insn() is doing
bpf_alu_string[BPF_OP(insn->code) >> 4]
and
bpf_jmp_string[BPF_OP(insn->code) >> 4]
where BPF_OP is a 4-bit instruction opcode.
Malformed insns can cause out of bounds access.
Fix it by sizing arrays appropriately.

The bug was found by clang address sanitizer with libfuzzer.
Reported-by: NYonghong Song <yhs@plumgrid.com>
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Problem:
The ecmp route replace support for ipv6 in the kernel, deletes the
existing ecmp route too early, ie when it installs the first nexthop.
If there is an error in installing the subsequent nexthops, its too late
to recover the already deleted existing route leaving the fib
in an inconsistent state.

This patch reduces the possibility of this by doing the following:
a) Changes the existing multipath route add code to a two stage process:
  build rt6_infos + insert them
	ip6_route_add rt6_info creation code is moved into
	ip6_route_info_create.
b) This ensures that most errors are caught during building rt6_infos
  and we fail early
c) Separates multipath add and del code. Because add needs the special
  two stage mode in a) and delete essentially does not care.
d) In any event if the code fails during inserting a route again, a
  warning is printed (This should be unlikely)

Before the patch:
$ip -6 route show
3000:1000:1000:1000::2 via fe80::202:ff:fe00:b dev swp49s0 metric 1024
3000:1000:1000:1000::2 via fe80::202:ff:fe00:d dev swp49s1 metric 1024
3000:1000:1000:1000::2 via fe80::202:ff:fe00:f dev swp49s2 metric 1024

/* Try replacing the route with a duplicate nexthop */
$ip -6 route change 3000:1000:1000:1000::2/128 nexthop via
fe80::202:ff:fe00:b dev swp49s0 nexthop via fe80::202:ff:fe00:d dev
swp49s1 nexthop via fe80::202:ff:fe00:d dev swp49s1
RTNETLINK answers: File exists

$ip -6 route show
/* previously added ecmp route 3000:1000:1000:1000::2 dissappears from
 * kernel */

After the patch:
$ip -6 route show
3000:1000:1000:1000::2 via fe80::202:ff:fe00:b dev swp49s0 metric 1024
3000:1000:1000:1000::2 via fe80::202:ff:fe00:d dev swp49s1 metric 1024
3000:1000:1000:1000::2 via fe80::202:ff:fe00:f dev swp49s2 metric 1024

/* Try replacing the route with a duplicate nexthop */
$ip -6 route change 3000:1000:1000:1000::2/128 nexthop via
fe80::202:ff:fe00:b dev swp49s0 nexthop via fe80::202:ff:fe00:d dev
swp49s1 nexthop via fe80::202:ff:fe00:d dev swp49s1
RTNETLINK answers: File exists

$ip -6 route show
3000:1000:1000:1000::2 via fe80::202:ff:fe00:b dev swp49s0 metric 1024
3000:1000:1000:1000::2 via fe80::202:ff:fe00:d dev swp49s1 metric 1024
3000:1000:1000:1000::2 via fe80::202:ff:fe00:f dev swp49s2 metric 1024

Fixes: 27596472 ("ipv6: fix ECMP route replacement")
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We may already have gotten a proper fd struct through fdget(), so
whenever we return at the end of an map operation, we need to call
fdput(). However, each map operation from syscall side first probes
CHECK_ATTR() to verify that unused fields in the bpf_attr union are
zero.

In case of malformed input, we return with error, but the lookup to
the map_fd was already performed at that time, so that we return
without an corresponding fdput(). Fix it by performing an fdget()
only right before bpf_map_get(). The fdget() invocation on maps in
the verifier is not affected.

Fixes: db20fd2b ("bpf: add lookup/update/delete/iterate methods to BPF maps")
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There was no verification that an underlying transport exists when creating
a connection, this would cause dereferencing a NULL ptr.

It might happen on sockets that weren't properly bound before attempting to
send a message, which will cause a NULL ptr deref:

[135546.047719] kasan: GPF could be caused by NULL-ptr deref or user memory accessgeneral protection fault: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC KASAN
[135546.051270] Modules linked in:
[135546.051781] CPU: 4 PID: 15650 Comm: trinity-c4 Not tainted 4.2.0-next-20150902-sasha-00041-gbaa1222-dirty #2527
[135546.053217] task: ffff8800835bc000 ti: ffff8800bc708000 task.ti: ffff8800bc708000
[135546.054291] RIP: __rds_conn_create (net/rds/connection.c:194)
[135546.055666] RSP: 0018:ffff8800bc70fab0  EFLAGS: 00010202
[135546.056457] RAX: dffffc0000000000 RBX: 0000000000000f2c RCX: ffff8800835bc000
[135546.057494] RDX: 0000000000000007 RSI: ffff8800835bccd8 RDI: 0000000000000038
[135546.058530] RBP: ffff8800bc70fb18 R08: 0000000000000001 R09: 0000000000000000
[135546.059556] R10: ffffed014d7a3a23 R11: ffffed014d7a3a21 R12: 0000000000000000
[135546.060614] R13: 0000000000000001 R14: ffff8801ec3d0000 R15: 0000000000000000
[135546.061668] FS:  00007faad4ffb700(0000) GS:ffff880252000000(0000) knlGS:0000000000000000
[135546.062836] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[135546.063682] CR2: 000000000000846a CR3: 000000009d137000 CR4: 00000000000006a0
[135546.064723] Stack:
[135546.065048]  ffffffffafe2055c ffffffffafe23fc1 ffffed00493097bf ffff8801ec3d0008
[135546.066247]  0000000000000000 00000000000000d0 0000000000000000 ac194a24c0586342
[135546.067438]  1ffff100178e1f78 ffff880320581b00 ffff8800bc70fdd0 ffff880320581b00
[135546.068629] Call Trace:
[135546.069028] ? __rds_conn_create (include/linux/rcupdate.h:856 net/rds/connection.c:134)
[135546.069989] ? rds_message_copy_from_user (net/rds/message.c:298)
[135546.071021] rds_conn_create_outgoing (net/rds/connection.c:278)
[135546.071981] rds_sendmsg (net/rds/send.c:1058)
[135546.072858] ? perf_trace_lock (include/trace/events/lock.h:38)
[135546.073744] ? lockdep_init (kernel/locking/lockdep.c:3298)
[135546.074577] ? rds_send_drop_to (net/rds/send.c:976)
[135546.075508] ? __might_fault (./arch/x86/include/asm/current.h:14 mm/memory.c:3795)
[135546.076349] ? __might_fault (mm/memory.c:3795)
[135546.077179] ? rds_send_drop_to (net/rds/send.c:976)
[135546.078114] sock_sendmsg (net/socket.c:611 net/socket.c:620)
[135546.078856] SYSC_sendto (net/socket.c:1657)
[135546.079596] ? SYSC_connect (net/socket.c:1628)
[135546.080510] ? trace_dump_stack (kernel/trace/trace.c:1926)
[135546.081397] ? ring_buffer_unlock_commit (kernel/trace/ring_buffer.c:2479 kernel/trace/ring_buffer.c:2558 kernel/trace/ring_buffer.c:2674)
[135546.082390] ? trace_buffer_unlock_commit (kernel/trace/trace.c:1749)
[135546.083410] ? trace_event_raw_event_sys_enter (include/trace/events/syscalls.h:16)
[135546.084481] ? do_audit_syscall_entry (include/trace/events/syscalls.h:16)
[135546.085438] ? trace_buffer_unlock_commit (kernel/trace/trace.c:1749)
[135546.085515] rds_ib_laddr_check(): addr 36.74.25.172 ret -99 node type -1
Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NSasha Levin <sasha.levin@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit f48da8b1 (xen-netback: fix
unlimited guest Rx internal queue and carrier flapping) introduced a
regression.

The PV frontend in IPXE only places 4 requests on the guest Rx ring.
Since netback required at least (MAX_SKB_FRAGS + 1) slots, IPXE could
not receive any packets.

a) If GSO is not enabled on the VIF, fewer guest Rx slots are required
   for the largest possible packet.  Calculate the required slots
   based on the maximum GSO size or the MTU.

   This calculation of the number of required slots relies on
   1650d545 (xen-netback: always fully coalesce guest Rx packets)
   which present in 4.0-rc1 and later.

b) Reduce the Rx stall detection to checking for at least one
   available Rx request.  This is fine since we're predominately
   concerned with detecting interfaces which are down and thus have
   zero available Rx requests.
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Reviewed-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hariprasad Shenai says:

====================
cxgb4: Fix tx flit calculation and wc stat configuration

This patch series fixes the following:
Patch 1/2 fixes tx flit calculation, which if wrong can lead to
stall, hang, data corrpution, write combining failure. Patch 2/2 fixes
PCI-E write combining stats configuration.

This patch series has been created against net tree and includes
patches on cxgb4 driver.

We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The write-combining configuration register SGE_STAT_CFG_A needs to
be configured after FW initializes the adapter, else FW will reset
the configuration
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 0aac3f56 ("cxgb4: Add comment for calculate tx flits
and sge length code") introduced a regression where tx flit calculation
is going wrong, which can lead to data corruption, hang, stall and
write-combining failure. Fixing it.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call netif_carrier_off() prior to register_netdev(), otherwise
userspace can see incorrect link state.
Signed-off-by: NAtsushi Nemoto <nemoto@toshiba-tops.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If an attempt to wake up users of broadcast link is made when there is
no enough place in send queue than it may hang up inside the
tipc_sk_rcv() function since the loop breaks only after the wake up
queue becomes empty. This can lead to complete CPU stall with the
following message generated by RCU:

INFO: rcu_sched self-detected stall on CPU { 0}  (t=2101 jiffies
					g=54225 c=54224 q=11465)
Task dump for CPU 0:
tpch            R  running task        0 39949  39948 0x0000000a
 ffffffff818536c0 ffff88181fa037a0 ffffffff8106a4be 0000000000000000
 ffffffff818536c0 ffff88181fa037c0 ffffffff8106d8a8 ffff88181fa03800
 0000000000000001 ffff88181fa037f0 ffffffff81094a50 ffff88181fa15680
Call Trace:
 <IRQ>  [<ffffffff8106a4be>] sched_show_task+0xae/0x120
 [<ffffffff8106d8a8>] dump_cpu_task+0x38/0x40
 [<ffffffff81094a50>] rcu_dump_cpu_stacks+0x90/0xd0
 [<ffffffff81097c3b>] rcu_check_callbacks+0x3eb/0x6e0
 [<ffffffff8106e53f>] ? account_system_time+0x7f/0x170
 [<ffffffff81099e64>] update_process_times+0x34/0x60
 [<ffffffff810a84d1>] tick_sched_handle.isra.18+0x31/0x40
 [<ffffffff810a851c>] tick_sched_timer+0x3c/0x70
 [<ffffffff8109a43d>] __run_hrtimer.isra.34+0x3d/0xc0
 [<ffffffff8109aa95>] hrtimer_interrupt+0xc5/0x1e0
 [<ffffffff81030d52>] ? native_smp_send_reschedule+0x42/0x60
 [<ffffffff81032f04>] local_apic_timer_interrupt+0x34/0x60
 [<ffffffff810335bc>] smp_apic_timer_interrupt+0x3c/0x60
 [<ffffffff8165a3fb>] apic_timer_interrupt+0x6b/0x70
 [<ffffffff81659129>] ? _raw_spin_unlock_irqrestore+0x9/0x10
 [<ffffffff8107eb9f>] __wake_up_sync_key+0x4f/0x60
 [<ffffffffa313ddd1>] tipc_write_space+0x31/0x40 [tipc]
 [<ffffffffa313dadf>] filter_rcv+0x31f/0x520 [tipc]
 [<ffffffffa313d699>] ? tipc_sk_lookup+0xc9/0x110 [tipc]
 [<ffffffff81659259>] ? _raw_spin_lock_bh+0x19/0x30
 [<ffffffffa314122c>] tipc_sk_rcv+0x2dc/0x3e0 [tipc]
 [<ffffffffa312e7ff>] tipc_bclink_wakeup_users+0x2f/0x40 [tipc]
 [<ffffffffa313ce26>] tipc_node_unlock+0x186/0x190 [tipc]
 [<ffffffff81597c1c>] ? kfree_skb+0x2c/0x40
 [<ffffffffa313475c>] tipc_rcv+0x2ac/0x8c0 [tipc]
 [<ffffffffa312ff58>] tipc_l2_rcv_msg+0x38/0x50 [tipc]
 [<ffffffff815a76d3>] __netif_receive_skb_core+0x5a3/0x950
 [<ffffffff815a98d3>] __netif_receive_skb+0x13/0x60
 [<ffffffff815a993e>] netif_receive_skb_internal+0x1e/0x90
 [<ffffffff815aa138>] napi_gro_receive+0x78/0xa0
 [<ffffffffa07f93f4>] tg3_poll_work+0xc54/0xf40 [tg3]
 [<ffffffff81597c8c>] ? consume_skb+0x2c/0x40
 [<ffffffffa07f9721>] tg3_poll_msix+0x41/0x160 [tg3]
 [<ffffffff815ab0f2>] net_rx_action+0xe2/0x290
 [<ffffffff8104b92a>] __do_softirq+0xda/0x1f0
 [<ffffffff8104bc26>] irq_exit+0x76/0xa0
 [<ffffffff81004355>] do_IRQ+0x55/0xf0
 [<ffffffff8165a12b>] common_interrupt+0x6b/0x6b
 <EOI>

The issue occurs only when tipc_sk_rcv() is used to wake up postponed
senders:

	tipc_bclink_wakeup_users()
		// wakeupq - is a queue which consists of special
		// 		 messages with SOCK_WAKEUP type.
		tipc_sk_rcv(wakeupq)
			...
			while (skb_queue_len(inputq)) {
				filter_rcv(skb)
					// Here the type of message is checked
					// and if it is SOCK_WAKEUP then
					// it tries to wake up a sender.
					tipc_write_space(sk)
						wake_up_interruptible_sync_poll()
			}

After the sender thread is woke up it can gather control and perform
an attempt to send a message. But if there is no enough place in send
queue it will call link_schedule_user() function which puts a message
of type SOCK_WAKEUP to the wakeup queue and put the sender to sleep.
Thus the size of the queue actually is not changed and the while()
loop never exits.

The approach I proposed is to wake up only senders for which there is
enough place in send queue so the described issue can't occur.
Moreover the same approach is already used to wake up senders on
unicast links.

I have got into the issue on our product code but to reproduce the
issue I changed a benchmark test application (from
tipcutils/demos/benchmark) to perform the following scenario:
	1. Run 64 instances of test application (nodes). It can be done
	   on the one physical machine.
	2. Each application connects to all other using TIPC sockets in
	   RDM mode.
	3. When setup is done all nodes start simultaneously send
	   broadcast messages.
	4. Everything hangs up.

The issue is reproducible only when a congestion on broadcast link
occurs. For example, when there are only 8 nodes it works fine since
congestion doesn't occur. Send queue limit is 40 in my case (I use a
critical importance level) and when 64 nodes send a message at the
same moment a congestion occurs every time.
Signed-off-by: NDmitry S Kolmakov <kolmakov.dmitriy@huawei.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the unnecessary switchdev.h include from br_netlink.c.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since __vlan_del can return an error code, change its inner function
__vlan_vid_del to return an eventual error from switchdev_port_obj_del.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The comparison check between cur_hw_state and hw_state is currently
invalid because cur_hw_state is right shifted by G_MISTP_SHIFT, while
hw_state is not, so we end-up comparing bits 2:0 with bits 7:5, which is
going to cause an additional aging to occur. Fix this by not shifting
cur_hw_state while reading it, but instead, mask the value with the
appropriately shitfted bitmask.

The other problem with the fast-ageing process is that we did not set
the EN_AGE_DYNAMIC bit to request the ageing to occur for dynamically
learned MAC addresses. Finally, write back 0 to the FAST_AGE_CTRL
register to avoid leaving spurious bits sets from one operation to the
other.

Fixes: 12f460f2 ("net: dsa: bcm_sf2: add HW bridging support")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function device_get_mac_address is trying different property names
in order to get the mac address. To check the return value, the variable
addr (which contain the buffer pass by the caller) will be re-used. This
means that if the previous property is not found, the next property will
be read using a NULL buffer.

Therefore it's only possible to retrieve the mac if node contains a
property "mac-address". Fix it by using a temporary buffer for the
return value.

This has been introduced by commit 4c96b7dc
"Add a matching set of device_ functions for determining mac/phy"
Signed-off-by: NJulien Grall <julien.grall@citrix.com>
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: NJeremy Linton <jeremy.linton@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The race may happen when a device (e.g. YOTA 4G LTE Modem) is
unplugged while the system is downloading a large file from the Net.

Hardware breakpoints and Kprobes with delays were used to confirm that
the race does actually happen.

The race is on skb_queue ('next' pointer) between usbnet_stop()
and rx_complete(), which, in turn, calls usbnet_bh().

Here is a part of the call stack with the code where the changes to the
queue happen. The line numbers are for the kernel 4.1.0:

*0 __skb_unlink (skbuff.h:1517)
    prev->next = next;
*1 defer_bh (usbnet.c:430)
    spin_lock_irqsave(&list->lock, flags);
    old_state = entry->state;
    entry->state = state;
    __skb_unlink(skb, list);
    spin_unlock(&list->lock);
    spin_lock(&dev->done.lock);
    __skb_queue_tail(&dev->done, skb);
    if (dev->done.qlen == 1)
        tasklet_schedule(&dev->bh);
    spin_unlock_irqrestore(&dev->done.lock, flags);
*2 rx_complete (usbnet.c:640)
    state = defer_bh(dev, skb, &dev->rxq, state);

At the same time, the following code repeatedly checks if the queue is
empty and reads these values concurrently with the above changes:

*0  usbnet_terminate_urbs (usbnet.c:765)
    /* maybe wait for deletions to finish. */
    while (!skb_queue_empty(&dev->rxq)
        && !skb_queue_empty(&dev->txq)
        && !skb_queue_empty(&dev->done)) {
            schedule_timeout(msecs_to_jiffies(UNLINK_TIMEOUT_MS));
            set_current_state(TASK_UNINTERRUPTIBLE);
            netif_dbg(dev, ifdown, dev->net,
                  "waited for %d urb completions\n", temp);
    }
*1  usbnet_stop (usbnet.c:806)
    if (!(info->flags & FLAG_AVOID_UNLINK_URBS))
        usbnet_terminate_urbs(dev);

As a result, it is possible, for example, that the skb is removed from
dev->rxq by __skb_unlink() before the check
"!skb_queue_empty(&dev->rxq)" in usbnet_terminate_urbs() is made. It is
also possible in this case that the skb is added to dev->done queue
after "!skb_queue_empty(&dev->done)" is checked. So
usbnet_terminate_urbs() may stop waiting and return while dev->done
queue still has an item.

Locking in defer_bh() and usbnet_terminate_urbs() was revisited to avoid
this race.
Signed-off-by: NEugene Shatokhin <eugene.shatokhin@rosalab.ru>
Reviewed-by: NBjørn Mork <bjorn@mork.no>
Acked-by: NOliver Neukum <oneukum@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c: In function ‘init_one’:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4579:8: warning: ‘chip’ may be used uninitialized in this function [-Wmaybe-uninitialized]
   chip |= CHELSIO_CHIP_CODE(CHELSIO_T4, pl_rev);
        ^
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4571:11: note: ‘chip’ was declared here
  int ver, chip;
           ^

Fixes: d86bd29e ("cxgb4/cxgb4vf: read the correct bits of PL Who Am I register")
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I've noticed  that fixed_phy_register() ignores its 'irq' parameter instead of
passing it to fixed_phy_add(). Luckily, fixed_phy_register()  seems to  always
be  called with PHY_POLL  for 'irq'... :-)

Fixes: a7595121 ("net: phy: extend fixed driver with fixed_phy_register()")
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's no particular desire to have conntrack action support in Open
vSwitch as an independently configurable bit, rather just to ensure
there is not a hard dependency. This exposed option doesn't accurately
reflect the conntrack dependency when enabled, so simplify this by
removing the option. Compile the support if NF_CONNTRACK is enabled.

Fixes: 7f8a436e ("openvswitch: Add conntrack action")
Signed-off-by: NJoe Stringer <joestringer@nicira.com>
Acked-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Marvell 88E6171 switch is in the 88E6351 family, which supports
802.1Q, thus add support from the generic mv88e6xxx functions.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2015-09-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
For the first round of fixes, we have this:
 * fix for the sizeof() pointer type issue
 * a fix for regulatory getting into a restore loop
 * a fix for rfkill global 'all' state, it needs to be stored
   everywhere to apply correctly to new rfkill instances
 * properly refuse CQM RSSI when it cannot actually be used
 * protect HT TDLS traffic properly in non-HT networks
 * don't incorrectly advertise 80 MHz support when not allowed
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If NO_DMA=y:

    ERROR: "dma_alloc_coherent" [drivers/net/ethernet/synopsys/dwc_eth_qos.ko] undefined!
    ERROR: "dma_free_coherent" [drivers/net/ethernet/synopsys/dwc_eth_qos.ko] undefined!
    ERROR: "dma_unmap_single" [drivers/net/ethernet/synopsys/dwc_eth_qos.ko] undefined!
    ERROR: "dma_map_page" [drivers/net/ethernet/synopsys/dwc_eth_qos.ko] undefined!
    ERROR: "dma_mapping_error" [drivers/net/ethernet/synopsys/dwc_eth_qos.ko] undefined!
    ERROR: "dma_map_single" [drivers/net/ethernet/synopsys/dwc_eth_qos.ko] undefined!
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NLars Persson <larper@axis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/vxlan.c: In function ‘vxlan_udp_encap_recv’:
drivers/net/vxlan.c:1226: warning: ‘info’ may be used uninitialized in this function

While this warning is a false positive, it can be killed easily by
getting rid of the pointer intermediary and referring directly to the
ip_tunnel_info structure.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: NJiri Benc <jbenc@redhat.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net/usb/lan78xx.c: In function ‘lan78xx_link_reset’:
net/usb/lan78xx.c:1107: warning: comparison is always false due to limited range of data type
net/usb/lan78xx.c:1111: warning: comparison is always false due to limited range of data type

Assigning return values that can be negative error codes to "u16"
variables makes them positive, ignoring the errors.  Hence use "int"
instead.

Drop the "unlikely"s (unlikely considered harmful) and propagate the
actual error values instead of overriding them to -EIO while we're at
it.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only return a conn if the rds_conn_net(conn) matches the struct
net passed to rds_conn_lookup().

Fixes: 467fa153 ("RDS-TCP: Support multiple RDS-TCP listen endpoints,
       one per netns.")
Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If fec MDIO write method succeeds its return value comes from
call to pm_runtime_get_sync().
But pm_runtime_get_sync() can also return 1.

In case of Micrel KSZ9031 PHY this value will then
be returned along the call chain of phy_write() ->
ksz9031_extended_write() -> ksz9031_center_flp_timing() ->
ksz9031_config_init() -> phy_init_hw() -> phy_attach_direct() ->
phy_connect_direct().

Then phy_connect() will cast it into a pointer using ERR_PTR(),
which then fec_enet_mii_probe() will try to dereference
resulting in an oops.

Fix it by normalizing return value of pm_runtime_get_sync()
to be zero if positive in MDIO write method.

Fixes: 8fff755e ("net: fec: Ensure clocks are enabled while using mdio bus")
Signed-off-by: NMaciej Szmigiero <mail@maciej.szmigiero.name>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

switchdev_port_fdb_dump is used as .ndo_fdb_dump. Its return value is
idx, so we cannot return errval.

Fixes: 45d4122c ("switchdev: add support for fdb add/del/dump via switchdev_port_obj ops.")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: Scott Feldman<sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The be_cmd_rx_filter() routine sends a non-embedded cmd to the FW and used
a pre-allocated dma memory to hold the cmd payload. This worked fine when
this cmd was synchronous. This cmd was changed to asynchronous mode by the
commit 8af65c2f("make the RX_FILTER command asynchronous"). So now when
there are two quick invocations of this cmd, the 2nd request may end up
overwriting the first request, causing FW cmd corruption.

This patch reverts the offending commit and hence fixes the regression.

Fixes: 8af65c2f("be2net: make the RX_FILTER command asynchronous")
Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	include/net/netfilter/nf_conntrack.h

The conflict was an overlap between changing the type of the zone
argument to nf_ct_tmpl_alloc() whilst exporting nf_ct_tmpl_free.

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for net, they are:

1) Oneliner to restore maps in nf_tables since we support addressing registers
   at 32 bits level.

2) Restore previous default behaviour in bridge netfilter when CONFIG_IPV6=n,
   oneliner from Bernhard Thaler.

3) Out of bound access in ipset hash:net* set types, reported by Dave Jones'
   KASan utility, patch from Jozsef Kadlecsik.

4) Fix ipset compilation with gcc 4.4.7 related to C99 initialization of
   unnamed unions, patch from Elad Raz.

5) Add a workaround to address inconsistent endianess in the res_id field of
   nfnetlink batch messages, reported by Florian Westphal.

6) Fix error paths of CT/synproxy since the conntrack template was moved to use
   kmalloc, patch from Daniel Borkmann.

All of them look good to me to reach 4.2, I can route this to -stable myself
too, just let me know what you prefer.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_get_by_name() will increment the usage count if the matching device
is found. But we were not decrementing the count if we have got the
device and the device is non-active.
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the IPv6 multicast routing code the mrt_lock was not being released
correctly in the MFC iterator, as a result adding or deleting a MIF would
cause a hang because the mrt_lock could not be acquired.

This fix is a copy of the code for the IPv4 case and ensures that the lock
is released correctly.
Signed-off-by: NRichard Laing <richard.laing@alliedtelesis.co.nz>
Acked-by: NCong Wang <cwang@twopensource.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When beacon filtering is enabled the mac80211 software implementation
for RSSI CQM cannot work as beacons will not be available. Rather than
accepting such a configuration without proper effect, reject it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently if 80MHz channels are not allowed for use, the VHT IE is not
included in the probe request for an AP. This is not good enough if the
AP is configured with the wrong regulatory and supports VHT even where
prohibited or in TDLS scenarios.
Mark the ifmgd with the DISABLE_VHT flag for the misbehaving-AP case, and
unset VHT support from the peer-station entry for the TDLS case.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

restore_regulatory_settings() should restore alpha2
as computed in restore_alpha2(), not raw user_alpha2 to
behave as described in the comment just above that code.

This fixes endless loop of calling CRDA for "00" and "97"
countries after resume from suspend on my laptop.

Looks like others had the same problem, too:
http://ath9k-devel.ath9k.narkive.com/knY5W6St/ath9k-and-crda-messages-in-logs
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/899335
https://forum.porteus.org/viewtopic.php?t=4975&p=36436
https://forums.opensuse.org/showthread.php/483356-Authentication-Regulatory-Domain-issues-ath5k-12-2Signed-off-by: NMaciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When switching the state of all RFKill switches of type all we need to
replicate the RFKILL_TYPE_ALL global state to all the other types global
state, so it is used to initialize persistent RFKill switches on
register.
Signed-off-by: NJoão Paulo Rechi Vita <jprvita@endlessm.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

HT TDLS traffic should be protected in a non-HT BSS to avoid
collisions. Therefore, when TDLS peers join/leave, check if
protection is (now) needed and set the ht_operation_mode of
the virtual interface according to the HT capabilities of the
TDLS peer(s).

This works because a non-HT BSS connection never sets (or
otherwise uses) the ht_operation_mode; it just means that
drivers must be aware that this field applies to all HT
traffic for this virtual interface, not just the traffic
within the BSS. Document that.
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The rate_control_cap_mask() function takes a parameter mcs_mask, which
GCC will take to be u8 * even though it was declared with a fixed size.
This causes the following warning:

	net/mac80211/rate.c: In function 'rate_control_cap_mask':
	net/mac80211/rate.c:719:25: warning: 'sizeof' on array function parameter 'mcs_mask' will return size of 'u8 * {aka unsigned char *}' [-Wsizeof-array-argument]
	   for (i = 0; i < sizeof(mcs_mask); i++)
	                         ^
	net/mac80211/rate.c:684:10: note: declared here
	       u8 mcs_mask[IEEE80211_HT_MCS_MASK_LEN],
	          ^

This can be easily fixed by using the IEEE80211_HT_MCS_MASK_LEN directly
within the loop condition.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Marcelo Ricardo Leitner says:

====================
couple of sctp fixes for 0ca50d12

These are two fixes for sctp after my patch on 0ca50d12 ("sctp: fix
src address selection if using secondary addresses")

The first, fix a dst leak on those it decided to skip.

The second, adds the fallback on src selection that Vlad had asked
about. Unfortunatelly a lot of ipvs setups relies on the old behavior
and I don't see a better fix for it.

Please consider both to -stable tree.
====================
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>