This patch adds a driver for external IRQ pins connected
to the INTC block on recent SoCs from Renesas.

The INTC hardware block usually contains a rather wide
range of features ranging from external IRQ pin handling
to legacy interrupt controller support. On older SoCs
the INTC is used as a general purpose interrupt controller
both for external IRQ pins and on-chip devices.

On more recent ARM based SoCs with Cortex-A9 the main
interrupt controller is the GIC, but IRQ trigger setup
still need to happen in the INTC hardware block.

This driver implements the glue code needed to configure
IRQ trigger and also handle mask/unmask and demux of
external IRQ pins hooked up from the INTC to the GIC.

Tested on sh73a0 and r8a7779. The hardware varies quite
a bit with SoC model, for instance register width and
bitfield widths vary wildly. The driver requires one GIC
SPI per external IRQ pin to operate.  Each driver instance
will handle up to 8 external IRQ pins.

The SoCs using this driver are currently mainly used
together with regular platform devices so this driver
allows configuration via platform data to support things
like static interrupt base address. DT support will
be added incrementally in the not so distant future.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Now that we have drivers/irqchip, move VIC irqchip to drivers/irqchip.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>

Now that we have drivers/irqchip, move GIC irqchip to drivers/irqchip. This
is necessary to share the GIC with arm and arm64.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>

With the recent creation of the drivers/irqchip/ directory, it is
desirable to move irq controller drivers here. At the moment, the only
driver here is irq-bcm2835, the driver for the irq controller found in
the ARM BCM2835 SoC, present in Rasberry Pi systems. This irq
controller driver was exporting its initialization function and its
irq handling function through a header file in
<linux/irqchip/bcm2835.h>.

When proposing to also move another irq controller driver in
drivers/irqchip, Rob Herring raised the very valid point that moving
things to drivers/irqchip was good in order to remove more stuff from
arch/arm, but if it means adding gazillions of headers files in
include/linux/irqchip/, it would not be very nice.

So, upon the suggestion of Rob Herring and Arnd Bergmann, this commit
introduces a small infrastructure that defines a central
irqchip_init() function in drivers/irqchip/irqchip.c, which is meant
to be called as the ->init_irq() callback of ARM platforms. This
function calls of_irq_init() with an array of match strings and init
functions generated from a special linker section.

Note that the irq controller driver initialization function is
responsible for setting the global handle_arch_irq() variable, so that
ARM platforms no longer have to define the ->handle_irq field in their
DT_MACHINE structure.

A global header, <linux/irqchip.h> is also added to expose the single
irqchip_init() function to the reset of the kernel.

A further commit moves the BCM2835 irq controller driver to this new
small infrastructure, therefore removing the include/linux/irqchip/
directory.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: NStephen Warren <swarren@wwwdotorg.org>
Reviewed-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
[rob.herring: reword commit message to reflect use of linker sections.]
Signed-off-by: NRob Herring <rob.herring@calxeda.com>

This moves the Versatile FPGA interrupt controller driver, used in
the Integrator/AP, Integrator/CP and some Versatile boards, out
of arch/arm/plat-versatile and down to drivers/irqchip where we
have consensus that such drivers belong. The header file is
consequently moved to <linux/platform_data/irq-versatile-fpga.h>.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Commit 89214f00 "ARM: bcm2835: add interrupt controller driver" added an
empty drivers/irqchip/Kconfig. Empty files apparently don't work well
with git (sometimes, with some versions?) so add some dummy content to
resolve this issue.
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The BCM2835 contains a custom interrupt controller, which supports 72
interrupt sources using a 2-level register scheme. The interrupt
controller, or the HW block containing it, is referred to occasionally
as "armctrl" in the SoC documentation, hence the symbol naming in the
code.

This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split as of 2012/09/08, and modified as follows:

* s/bcm2708/bcm2835/.
* Modified device tree vendor prefix.
* Moved implementation to drivers/irchip/.
* Added devicetree documentation, and hence removed list of IRQs from
  bcm2835.dtsi.
* Changed shift in MAKE_HWIRQ() and HWIRQ_BANK() from 8 to 5 to reduce
  the size of the hwirq space, and pass the total size of the hwirq space
  to irq_domain_add_linear(), rather than just the number of valid hwirqs;
  the two are different due to the hwirq space being sparse.
* Added the interrupt controller DT node to the top-level of the DT,
  rather than nesting it inside a /axi node. Hence, changed the reg value
  since /axi had a ranges property. This seems simpler to me, but I'm not
  sure if everyone will like this change or not.
* Don't set struct irq_domain_ops.map = irq_domain_simple_map, hence
  removing the need to patch include/linux/irqdomain.h or
  kernel/irq/irqdomain.c.
* Simplified armctrl_of_init() using of_iomap().
* Removed unused IS_VALID_BANK()/IS_VALID_IRQ() macros.
* Renamed armctrl_handle_irq() to prevent possible symbol clashes.
* Made armctrl_of_init() static.
* Removed comment "Each bank is registered as a separate interrupt
  controller" since this is no longer true.
* Removed FSF address from license header.
* Added my name to copyright header.
Signed-off-by: NChris Boot <bootc@bootc.net>
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Signed-off-by: NDom Cobley <popcornmix@gmail.com>
Signed-off-by: NDom Cobley <dc4@broadcom.com>
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>

This patch adds basic header files for SPEAr13xx Machines.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>

Make tool build after virtio changes broke it.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Make the tool build again after virtio changes broke it.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>