Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The SPI node is out of date with regards to the binding for fsl-espi and
driver support.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

* Move SoC specific details like irq mapping to SoC dtsi
* Update interrupt property to cover both error interrupt and PCIe
  runtime interrupts
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

If we include the p1020rdb.dts instead of p1020si.dts we greatly reduce
duplication and maintenance.  We can just list which devices are
disabled for the given core and mpic protected sources.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Update of_platform_bus_probe() RapidIO node to be compitable with
new RapidIO dts compatible property.
Signed-off-by: NKai Jiang <Kai.Jiang@freescale.com>
Acked-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Usually, freescale rapidio endpoint can support one or two 1x or 4X
LP-Serial link interfaces, and rapidio message transactions can be
implemented by two message units. This adds the support of two
rapidio ports and initializes message unit 0 and message unit 1. And
these ports and message units can work simultaneously.
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NJin Qing <b24347@freescale.com>
Signed-off-by: NLiu Gang <Gang.Liu@freescale.com>
Acked-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The Freescale PowerPC RapidIO controller consists of a RapidIO endpoint and
a RapidIO message unit(RMU). Or use RapidIO message manager(RMan) to
replace the RMU in DPAA architecture. Therefore, we should split the code
into two function modules according to the hardware architecture. Add new
struct for RMU module, and new initialization function to set up RMU
module. This policy is very conducive to adding new module like RMan, or
adding multi-ports or message units support.
Signed-off-by: NLian Minghuan <Minghuan.Lian@freescale.com>
Signed-off-by: NLiu Gang <Gang.Liu@freescale.com>
Acked-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This document is created for powerpc rapidio and rmu nodes in dts file.
These nodes can support two rapidio ports and message units. In addition,
It explicates the properties and gives examples about rapidio and rmu nodes.
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NJin Qing <b24347@freescale.com>
Signed-off-by: NLiu Gang <Gang.Liu@freescale.com>
Acked-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

At this point, ehv_pic has been allocated but not stored anywhere, so it
should be freed before leaving the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@

x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
     when != if (...) { <+...kfree(x)...+> }
     when any
     when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
               when forall
(
 return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

If Freescale LBC driver fails to initialise itself from device tree, then
internal structure is freed only but not NULL-fied.  As result functions
fsl_lbc_find() after checking the structure is not NULL are trying to
access device registers.
Signed-off-by: NAlexandre Rusev <arusev@dev.rtsoft.ru>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

compatible in dts has been changed, so the driver needs to be updated
accordingly.
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

QE_General4 should only round up the divisor iff divisor is > 3.
Rounding up lower divisors makes the error too big, causing USB
on MPC832x to fail.
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

arch/powerpc/platforms/85xx/p3060_qds.c: In function '__machine_initcall_p3060_qds_declare_of_platform_devices':
arch/powerpc/platforms/85xx/p3060_qds.c:73:1: error: implicit declaration of function 'declare_of_platform_devices'

declare_of_platform_devices should have been corenet_ds_publish_devices.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The driver for the Freescale P3060 QDS got added by commit 96cc017c
("[...] Add support for P3060QDS board"). Its Kconfig entry selects
MPC8xxx_GPIO. But at the time that driver got added MPC8xxx_GPIO was
already renamed to GPIO_MPC8XXX, by commit c68308dd ("gpio: move
mpc8xxx/512x gpio driver to drivers/gpio").

So make this driver select GPIO_MPC8XXX.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

P1023 external IRQ[4:6, 11] are not pin out, but the interrupts are
utilized by the PCIe controllers.  As they are not exposed as pins we
need to set them as active-high (internal to the SoC these interrupts
are pulled down).

IRQs[0:3,7:10] are pulled up on the board so we have them set as
active-low.
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

* git://github.com/rustyrussell/linux:
  virtio-pci: make reset operation safer
  virtio-mmio: Correct the name of the guest features selector
  virtio: add HAS_IOMEM dependency to MMIO platform bus driver

virtio pci device reset actually just does an I/O
write, which in PCI is really posted, that is it
can complete on CPU before the device has received it.

Further, interrupts might have been pending on
another CPU, so device callback might get invoked after reset.

This conflicts with how drivers use reset, which is typically:
	reset
	unregister
a callback running after reset completed can race with
unregister, potentially leading to use after free bugs.

Fix by flushing out the write, and flushing pending interrupts.

This assumes that device is never reset from
its vq/config callbacks, or in parallel with being
added/removed, document this assumption.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Guest features selector spelling mistake.

Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: NSasha Levin <levinsasha928@gmail.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Fix this compile error on s390:

  CC [M]  drivers/virtio/virtio_mmio.o
drivers/virtio/virtio_mmio.c: In function 'vm_get_features':
drivers/virtio/virtio_mmio.c:107:2: error: implicit declaration of function 'writel'

Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: NPawel Moll <pawel.moll@arm.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

* 'upstream-linus' of git://github.com/jgarzik/libata-dev:
  libata: fix build without BMDMA
  [libata] ahci_platform: fix DT probing

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
  PCI hotplug: shpchp: don't blindly claim non-AMD 0x7450 device IDs
  PCI: pciehp: wait 100 ms after Link Training check
  PCI: pciehp: wait 1000 ms before Link Training check
  PCI: pciehp: Retrieve link speed after link is trained
  PCI: Let PCI_PRI depend on PCI
  PCI: Fix compile errors with PCI_ATS and !PCI_IOV
  PCI / ACPI: Make acpiphp ignore root bridges using PCIe native hotplug

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: Extend array bounds for all filename chars
  eCryptfs: Flush file in vma close
  eCryptfs: Prevent file create race condition

From mhalcrow's original commit message:

    Characters with ASCII values greater than the size of
    filename_rev_map[] are valid filename characters.
    ecryptfs_decode_from_filename() will access kernel memory beyond
    that array, and ecryptfs_parse_tag_70_packet() will then decrypt
    those characters. The attacker, using the FNEK of the crafted file,
    can then re-encrypt the characters to reveal the kernel memory past
    the end of the filename_rev_map[] array. I expect low security
    impact since this array is statically allocated in the text area,
    and the amount of memory past the array that is accessible is
    limited by the largest possible ASCII filename character.

This patch solves the issue reported by mhalcrow but with an
implementation suggested by Linus to simply extend the length of
filename_rev_map[] to 256. Characters greater than 0x7A are mapped to
0x00, which is how invalid characters less than 0x7A were previously
being handled.
Signed-off-by: NTyler Hicks <tyhicks@canonical.com>
Reported-by: NMichael Halcrow <mhalcrow@google.com>
Cc: stable@kernel.org

Dirty pages weren't being written back when an mmap'ed eCryptfs file was
closed before the mapping was unmapped. Since f_ops->flush() is not
called by the munmap() path, the lower file was simply being released.
This patch flushes the eCryptfs file in the vm_ops->close() path.

https://launchpad.net/bugs/870326Signed-off-by: NTyler Hicks <tyhicks@canonical.com>
Cc: stable@kernel.org [2.6.39+]

The file creation path prematurely called d_instantiate() and
unlock_new_inode() before the eCryptfs inode info was fully
allocated and initialized and before the eCryptfs metadata was written
to the lower file.

This could result in race conditions in subsequent file and inode
operations leading to unexpected error conditions or a null pointer
dereference while attempting to use the unallocated memory.

https://launchpad.net/bugs/813146Signed-off-by: NTyler Hicks <tyhicks@canonical.com>
Cc: stable@kernel.org

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
  ktest: Check parent options for iterated tests

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c: Make i2cdev_notifier_call static
  i2c: Delete ANY_I2C_BUS
  i2c: Fix device name for 10-bit slave address
  i2c-algo-bit: Generate correct i2c address sequence for 10-bit target

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: TPS65910: Fix VDD1/2 voltage selector count

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
  drm: integer overflow in drm_mode_dirtyfb_ioctl()
  drivers/gpu/vga/vgaarb.c: add missing kfree
  drm/radeon/kms/atom: unify i2c gpio table handling
  drm/radeon/kms: fix up gpio i2c mask bits for r4xx for real
  ttm: Don't return the bo reserved on error path
  drm/radeon/kms: add a CS ioctl flag not to rewrite tiling flags in the CS
  drm/i915: Fix inconsistent backlight level during disabled
  drm, i915: Fix memory leak in i915_gem_busy_ioctl().
  drm/i915: Use DPCD value for max DP lanes.
  drm/i915: Initiate DP link training only on the lanes we'll be using
  drm/i915: Remove trailing white space
  drm/i915: Try harder during dp pattern 1 link training
  drm/i915: Make DP prepare/commit consistent with DP dpms
  drm/i915: Let panel power sequencing hardware do its job
  drm/i915: Treat PCH eDP like DP in most places
  drm/i915: Remove link_status field from intel_dp structure
  drm/i915: Move common PCH_PP_CONTROL setup to ironlake_get_pp_control
  drm/i915: Module parameters using '-1' as default must be signed type
  drm/i915: Turn on another required clock gating bit on gen6.
  drm/i915: Turn on a required 3D clock gating bit on Sandybridge.
  ...

Count of selector voltage is required for regulator_set_voltage
to work via set_voltage_sel. VDD1/2 currently have it as zero,
so regulator_set_voltage won't work for VDD1/2.
Update count (n_voltages) for VDD1/2.

Output Voltage = (step value * 12.5 mV + 562.5 mV) * gain

With above expr, number of voltages that can be selected is
step value count * gain count

constant for gain count will be called VDD1_2_NUM_VOLT_COARSE

existing constant for step value count is VDD1_2_NUM_VOLTS,
use VDD1_2_NUM_VOLT_FINE instead to make clear that step value
is not the only component in deciding selectable voltage count
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The function i2cdev_notifier_call is used only in i2c-dev file
making it static.
Also removes the following sparse warning

drivers/i2c/i2c-dev.c:582:5: warning: symbol 'i2cdev_notifier_call'
was not declared. Should it be static?
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Last piece of code using ANY_I2C_BUS was deleted almost 2 years ago,
so ANY_I2C_BUS can go away as well.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

10-bit addresses overlap with traditional 7-bit addresses, leading in
device name collisions. Add an arbitrary offset to 10-bit addresses to
prevent this collision. The offset was chosen so that the address is
still easily recognizable.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>

The wrong bits were put on the wire, fix that.

This fixes kernel bug #42562.
Signed-off-by: NSheng-Hui J. Chu <jeffchu@broadcom.com>
Cc: stable@kernel.org
Signed-off-by: NJean Delvare <khali@linux-fr.org>

There is a potential integer overflow in drm_mode_dirtyfb_ioctl()
if userspace passes in a large num_clips.  The call to kmalloc would
allocate a small buffer, and the call to fb->funcs->dirty may result
in a memory corruption.
Reported-by: NHaogang Chen <haogangchen@gmail.com>
Signed-off-by: NXi Wang <xi.wang@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

This reverts commit dc937280.

As requested by Ben Herrenschmidt:
  "This breaks some powerpc platforms at least.  The practice of having
   a node provide an explicit "interrupt-parent" property pointing to
   itself is an old trick that we've used in the past to allow a
   device-node to have interrupts routed to different controllers.

   In that case, the node also contains an interrupt-map, so the node is
   its own parent, the interrupt resolution hits the map, which then can
   route each individual interrupt to a different parent."

Grant says:
  "Ah, nuts, yes that is broken then.  Yes, please revert the commit and
   Rob & I will come up with a better solution.

   Rob, I think it can be done by explicitly checking for np ==
   desc->interrupt_parent in of_irq_init() instead of relying on
   of_irq_find_parent() returning NULL."
Requested-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Cc: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  mount_subtree() pointless use-after-free
  iio: fix a leak due to improper use of anon_inode_getfd()
  microblaze: bury asm/namei.h

kbuf is a buffer that is local to this function, so all of the error paths
leaving the function should release it.
Signed-off-by: NJulia Lawall <julia@diku.dk>
Cc: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Split the quirks and i2c_rec assignment into separate
functions used by both radeon_lookup_i2c_gpio() and
radeon_atombios_i2c_init().  This avoids duplicating code
and cases where quirks were only added to one of the
functions.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>