The setting of the UDP tunnel GSO type is already performed by
udp[46]_gro_complete().
Signed-off-by: NJarno Rajahalme <jarno@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

qede requires qed to provide enough resources to accommodate 16 combined
channels, but that upper-bound isn't actually being enforced by it.
Instead, qed inform back to qede how many channels can be opened based on
available resources - but that calculation doesn't really take into account
the resources requested by qede; Instead it considers other FW/HW available
resources.

As a result, if a user would increase the number of channels to more than
16 [e.g., using ethtool] the chip would hang.

This change increments the resources requested by qede to 64 combined
channels instead of 16; This value is an upper bound on the possible
available channels [due to other FW/HW resources].
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use htons instead of unconditionally byte swapping nexthdr.  On a little
endian systems shifting the byte is correct behavior, but it results in
incorrect csums on big endian architectures.

Fixes: f8c6455b ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE')
Signed-off-by: NDaniel Jurgens <danielj@mellanox.com>
Reviewed-by: NCarol Soto <clsoto@us.ibm.com>
Tested-by: NCarol Soto <clsoto@us.ibm.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The multicast/all-multicast internal flags are not properly restored
after device reset.  This could lead to unreliable multicast operations
after an ethtool configuration change for example.

Call bnxt_mc_list_updated() and setup the vnic->mask in bnxt_init_chip()
to fix the issue.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code determines if the next ring entry is valid before proceeding
further to read the rest of the entry.  The CPU can re-order and read
the rest of the entry first, possibly reading a stale entry, if DMA
of a new entry happens right after reading it.  This issue can be
readily seen on a ppc64 system, causing it to crash.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the receive path a queue's work bit was cleared unconditionally even
if fec_enet_rx_queue only read out a part of the available packets from
the hardware. This resulted in not reading any packets in the next napi
turn and so packets were delayed or lost.

The obvious fix is to only clear a queue's bit when the queue was
emptied.

Fixes: 4d494cdc ("net: fec: change data structure to support multiqueue")
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Tested-by: NFugang Duan <fugang.duan@nxp.com>
Acked-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When probe bails out with an error, we try to unregister the
netdev before we have even registered it. Fix the goto statements
for that.
Signed-off-by: NMatthias Brugger <mbrugger@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current sequence makes us register for a network device prior to
registering and probing the MDIO bus which could lead to some unwanted
consequences, like a thread of execution calling into ndo_open before
register_netdev() returns, while the MDIO bus is not ready yet.

Rework the sequence to register for the MDIO bus, and therefore attach
to a PHY prior to calling register_netdev(), which implies reworking the
error path a bit.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 3b9d6da6 ("cpu/hotplug: Fix rollback during error-out
in __cpu_disable()") it is ensured that callbacks of CPU_ONLINE and
CPU_DOWN_PREPARE are processed on the hotplugged CPU. Due to this SMP
function calls are no longer required.

Replace smp_call_function_single() with a direct call to
mvneta_percpu_enable() or mvneta_percpu_disable(). The functions do
not require to be called with interrupts disabled, therefore the
smp_call_function_single() calling convention is not preserved.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NAnna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now mdiobus_scan() returns ERR_PTR(-ENODEV) instead of NULL if the PHY
device ID was read as all ones. As this was not  an error before, this
value  should be filtered out now in this driver.

Fixes: b74766a0 ("phylib: don't return NULL from get_phy_device()")
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since mdiobus_scan() returns either an error code or NULL on error, the
driver should check  for both,  not only for NULL, otherwise a crash is
imminent...
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vxlan add/delete port NDOs are called under rcu lock.
The current mlx5e implementation can potentially block in these
calls, which is not allowed.  Move to using the mlx5e workqueue
to handle these NDOs.

Fixes: b3f63c3d ('net/mlx5e: Add netdev support for VXLAN tunneling')
Signed-off-by: NMatthew Finlay <matt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement a mlx5e workqueue to handle all mlx5e specific tasks.  Move
all tasks currently using the system workqueue to the new workqueue.
This is in preparation for vxlan using the mlx5e workqueue in order to
schedule port add/remove operations.
Signed-off-by: NMatthew Finlay <matt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When MLX5_EN=y MLX5_CORE=y and VXLAN=m there is a linker error for
vxlan_get_rx_port() due to the fact that VXLAN is a module. Change Kconfig
to select VXLAN when MLX5_CORE=y. When MLX5_CORE=m there is no dependency
on the value of VXLAN.

Fixes: b3f63c3d ('net/mlx5e: Add netdev support for VXLAN tunneling')
Signed-off-by: NMatthew Finlay <matt@mellanox.com>
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When freeing UAR the driver tries to unmap uar->map and uar->bf_map
which are mutually exclusive thus always unmapping a NULL pointer.
Make sure we only call iounmap() once, for the actual mapping.

Fixes: 0ba42241 ('net/mlx5: Fix global UAR mapping')
Signed-off-by: NGal Pressman <galp@mellanox.com>
Reported-by: NDoron Tsur <doront@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An out of bounds read of 2 bytes was discovered in cxgb3 with KASAN.

t3_config_rss() expects both arrays it gets as parameters to have
terminators. setup_rss(), the caller, forgets to add a terminator to
one of the arrays. Thankfully the iteration in t3_config_rss() stops
anyway, but in the last iteration the check for the terminator
is an out of bounds read.

Add the missing terminator to rspq_map[].
Reported-by: NJan Stancek <jstancek@redhat.com>
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This takes the MAC address for smsc75xx/smsc95xx USB network devices
from a the device tree. This is required to get a usable persistent
address on the popular beagleboard, whose hardware designers
accidentally forgot that an ethernet device really requires an a
MAC address to be functional.

The Raspberry Pi also ships smsc9514 without a serial EEPROM, stores
the MAC address in ROM accessible via VC4 firmware.

The smsc75xx and smsc95xx drivers are just two copies of the
same code, so better fix both.

[lkundrak@v3.sk: updated to use of_get_property() as per suggestion from
Arnd, reworded the message and comments a bit]
Tested-by: NLubomir Rintel <lkundrak@v3.sk>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLubomir Rintel <lkundrak@v3.sk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a fixed-link DT subnode is used, the phy_device was looked up so
that a PHY ID string could be constructed and passed to phy_connect().
This is not necessary, as the device_node can be passed directly to
of_phy_connect() instead. This reuses the same codepath as if the
phy-handle DT property was used.
Signed-off-by: NDavid Rivshin <drivshin@allworx.com>
Tested-by: NNicolas Chauvet <kwizart@gmail.com>
Tested-by: NAndrew Goodbody <andrew.goodbody@cambrionix.com>
Reviewed-by: NMugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy-mode emac property was only being processed in the phy_id
or fixed-link cases. However if phy-handle was specified instead,
an error message would complain about the lack of phy_id or
fixed-link, and then jump past the of_get_phy_mode(). This would
result in the PHY mode defaulting to MII, regardless of what the
devicetree specified.

Fixes: 9e42f715 ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: NDavid Rivshin <drivshin@allworx.com>
Tested-by: NNicolas Chauvet <kwizart@gmail.com>
Tested-by: NAndrew Goodbody <andrew.goodbody@cambrionix.com>
Reviewed-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If an emac node has a phy-handle property that points to something
which is not a phy, then a segmentation fault will occur when the
interface is brought up. This is because while phy_connect() will
return ERR_PTR() on failure, of_phy_connect() will return NULL.
The common error check uses IS_ERR(), and so missed when
of_phy_connect() fails. The NULL pointer is then dereferenced.

Also, the common error message referenced slave->data->phy_id,
which would be empty in the case of phy-handle. Instead, use the
name of the device_node as a useful identifier. And in the phy_id
case add the error code for completeness.

Fixes: 9e42f715 ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: NDavid Rivshin <drivshin@allworx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 9e42f715 ("drivers: net: cpsw: add
phy-handle parsing") saved the "phy-handle" phandle into a new cpsw_priv
field. However, phy connections are per-slave, so the phy_node field should
be in cpsw_slave_data rather than cpsw_priv.

This would go unnoticed in a single emac configuration. But in dual_emac
mode, the last "phy-handle" property parsed for either slave would be used
by both of them, causing them both to refer to the same phy_device.

Fixes: 9e42f715 ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: NDavid Rivshin <drivshin@allworx.com>
Tested-by: NNicolas Chauvet <kwizart@gmail.com>
Tested-by: NAndrew Goodbody <andrew.goodbody@cambrionix.com>
Reviewed-by: NMugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The default Pegasus setup was to append the status and CRC at the end of each
received packet.  The status bits are used to update various stats, but CRC has
been ignored.  The new default is to not append CRC at the end of RX packets.
Signed-off-by: NPetko Manolov <petkan@mip-labs.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

usb_fill_bulk_urb() receives buffer length parameter 8 bytes larger
than what's allocated by alloc_skb(); This seems to be a problem with
older (pegasus usb-1.1) devices, which may silently return more data
than the maximal packet length.
Reported-by: NLincoln Ramsay <a1291762@gmail.com>
Signed-off-by: NPetko Manolov <petkan@mip-labs.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 13a56b44 ("at803x: Add support for hardware reset") added a
work-around for a hardware bug on the AT8030.  However, the work-around
was being called for all 803x PHYs, even those that don't need it.
Function at803x_link_change_notify() checks to make sure that it only
resets the PHY on the 8030, but it makes more sense to not call that
function at all if it isn't needed.
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The size allocated for target->hwinfo and the number of bytes copied in it
should be consistent.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At forced 100 Full & Half duplex mode, chip may fail to set mode correctly
when cable is switched between long(~50+m) and short one.
As workaround, set to 10 before setting to 100 at forced 100 F/H mode.
Signed-off-by: NWoojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix rx_bytes, tx_bytes and tx_frames error in netdev.stats.
- rx_bytes counted bytes excluding size of struct ethhdr.
- tx_packets didn't count multiple packets in a single urb
- tx_bytes included 8 bytes of extra commands.
Signed-off-by: NWoojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The error return err is not initialized and there is a possibility
that err is not assigned causing mv88e6xxx_port_bridge_join to
return a garbage error return status. Fix this by initializing err
to 0.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When configured in fixed link, the DaVinci emac driver sets the
priv->phydev to NULL and further ioctl calls to the phy_mii_ioctl()
causes the kernel to crash.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Fixes: 1bb6aa56 ("net: davinci_emac: Add support for fixed-link PHY")
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When certain firmware variants are selected (via the sfboot utility) the
SFC7000 and SFC8000 series NICs don't support RSS. The driver still
tries (and fails) to insert filters with the RSS flag, and the NIC fails
to pass traffic.

When the firmware reports RSS_LIMITED suppress allocating a default RSS
context. The absence of an RSS context is picked up in filter insertion
and RSS flags are discarded.
Signed-off-by: NBert Kenward <bkenward@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

napi_disable() can not be called with bh disabled, move locking just
around myri10ge_ss_lock_napi() .

Patches fixes following bug:

[  114.278378] BUG: sleeping function called from invalid context at net/core/dev.c:4383
<snip>
[  114.313712] Call Trace:
[  114.314943]  [<ffffffff817010ce>] dump_stack+0x19/0x1b
[  114.317673]  [<ffffffff810ce7f3>] __might_sleep+0x173/0x230
[  114.320566]  [<ffffffff815b3117>] napi_disable+0x27/0x90
[  114.323254]  [<ffffffffa01e437f>] myri10ge_close+0xbf/0x3f0 [myri10ge]
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NHyong-Youb Kim <hykim@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If PAGE_SIZE is bigger than BNXT_RX_PAGE_SIZE, that means the native CPU
page is bigger than the maximum length of the RX BD.  Divide the page
into multiple 32K buffers for the aggregation ring.

Add an offset field in the bnxt_sw_rx_agg_bd struct to keep track of the
page offset of each buffer.  Since each page can be referenced by multiple
buffer entries, call get_page() as needed to get the proper reference
count.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RX BD length field of this device is 16-bit, so the largest buffer
size is 65535.  For LRO and GRO, we allocate native CPU pages for the
aggregation ring buffers.  It won't work if the native CPU page size is
64K or bigger.

We fix this by defining BNXT_RX_PAGE_SIZE to be native CPU page size
up to 32K.  Replace PAGE_SIZE with BNXT_RX_PAGE_SIZE in all appropriate
places related to the rx aggregation ring logic.

The next patch will add additional logic to divide the page into 32K
chunks for aggrgation ring buffers if PAGE_SIZE is bigger than
BNXT_RX_PAGE_SIZE.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only MSI-X can be used on a VF.  The driver should fail initialization
if it cannot successfully enable MSI-X.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When multiple skb are TX-completed in a row, we might incorrectly keep
a timestamp of a prior skb and cause extra work.

Fixes: ec693d47 ("net/mlx4_en: Add HW timestamping (TS) support")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIvan Babrou <ivan@cloudflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces kexec support for mlx5.
When switching kernels, kexec() calls shutdown, which unloads
the driver and cleans its resources.

In addition, remove unregister netdev from shutdown flow. This will
allow a clean shutdown, even if some netdev clients did not release their
reference from this netdev. Releasing The HW resources only is enough as
the kernel is shutting down
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NHaggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The static is not required and breaks re-entrancy if it will be required.

Fixes: 25302363 ("net/mlx5_core: Flow steering tree initialization")
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set and report vport MTU rather than physical MTU,
Driver will set both vport and physical port mtu and will
rely on the query of vport mtu.

SRIOV VFs have to report their MTU to their vport manager (PF),
and this will allow them to work with any MTU they need
without failing the request.

Also for some cases where the PF is not a port owner, PF can
work with MTU less than the physical port mtu if set physical
port mtu didn't take effect.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Minimum MTU that can be set in Connectx4 device is 68.

This fixes the case where a user wants to set invalid MTU,
the driver will fail to satisfy this request and the interface
will stay down.

It is better to report an error and continue working with old
mtu.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>