We never invalidate PD entries and making them valid can
run with other users in parallel.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This allows us to finally remove the VM fence and
so allow concurrent use of it from different engines.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Use multiple VMIDs for each VM, one for each ring. That allows
us to execute flushes separately on each ring, still not ideal
cause in a lot of cases rings can share IDs.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Note for each fence if it's a VM page table update or not. This allows
us to determine the last VM update in a sync object and so to figure
out if we need to flush the TLB or not.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This allows us to add the real execution fence as shared.

v2: fix typo
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Previously we just allocated space for four hardware semaphores
in each software semaphore object. Make software semaphore objects
represent only one hardware semaphore address again by splitting
the sync code into it's own object.

v2: fix typo in comment
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The PD/PTs reservation object now contains everything needed.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

That's useless when all callers drop the reservation
immediately after calling the function.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Use ring structure instead of index and provide vm_id and pd_addr separately.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The current code always reprogrammed the sclk levels,
but we don't currently handle disp sclk requirements
so just skip it.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Preferred ordering.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Use unforce levels rather than enable mask instruction.
This is the preferred method.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Apply voltage changes for displays before changing clocks.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add missing newline and print the bad gpio shift.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Not currently used.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Enable smc fan control for CI boards.  Should
reduce the fan noise on systems with a higher
default fan profile.

v2: disable by default, add additional fan setup, rpm control

bug:
https://bugs.freedesktop.org/show_bug.cgi?id=73338Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Enable smc fan control for SI boards.  Should
reduce the fan noise on systems with a higher
default fan profile.

v2: disable by default, add rpm controls

bug:
https://bugs.freedesktop.org/show_bug.cgi?id=73338Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Always need to set bit 0 of RLC_CGTT_MGCG_OVERRIDE
to avoid unreliable doorbell updates in some cases.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

No functional change.
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The cursor_set2 hook provides the cursor hotspot position within the
cursor image. When the hotspot position changes, we can adjust the cursor
position such that the hotspot doesn't move on the screen. This prevents
the cursor from appearing to intermittently jump around on the screen
when the position of the hotspot within the cursor image changes.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Merge AMDKFD it seems clean enough.
* 'amdkfd-v6' of git://people.freedesktop.org/~gabbayo/linux: (29 commits)
  amdkfd: Implement the Get Version IOCTL
  amdkfd: Implement the Get Process Aperture IOCTL
  amdkfd: Implement the Get Clock Counters IOCTL
  amdkfd: Implement the Set Memory Policy IOCTL
  amdkfd: Implement the create/destroy/update queue IOCTLs
  amdkfd: Add interrupt handling module
  amdkfd: Add device queue manager module
  amdkfd: Add process queue manager module
  amdkfd: Add packet manager module
  amdkfd: Add module parameter of scheduling policy
  amdkfd: Add kernel queue module
  amdkfd: Add mqd_manager module
  amdkfd: Add queue module
  amdkfd: Add binding/unbinding calls to amd_iommu driver
  amdkfd: Add basic modules to amdkfd
  amdkfd: Add topology module to amdkfd
  amdkfd: Add amdkfd skeleton driver
  amdkfd: Add IOCTL set definitions of amdkfd
  Update MAINTAINERS and CREDITS files with amdkfd info
  drm/radeon: Add radeon <--> amdkfd interface
  ...

This patch allows framebuffers for cirrus to be created with
32bpp pixel formats provided that they do not violate certain
restrictions of the cirrus hardware.

v2: Use pci resource length for vram size.
Signed-off-by: NZach Reizner <zachr@google.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Only importing an FD to a handle is currently supported on UDL,
but the exporting functionality is equally useful.
Signed-off-by: NHaixia Shi <hshi@chromium.org>
Reviewed-by: NStéphane Marchesin <marcheu@chromium.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

By default set udl_gem_object as cacheable, but set WC flag when attaching
dmabuf. In udl_gem_mmap() update cache attributes based on the flags, similar
to exynos_drm_gem_mmap().
Signed-off-by: NHaixia Shi <hshi@chromium.org>
Reviewed-by: NSonny Rao <sonnyrao@chromium.org>
Reviewed-by: NOlof Johansson <olofj@chromium.org>
Reviewed-by: NStéphane Marchesin <marcheu@chromium.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Before this patch, cirrus_device_init could have failed while
cirrus_mm_init succeeded and the driver would have reported overall
success on load. This patch causes cirrus_device_init to return on
the first error encountered.
Reviewed-by: NStéphane Marchesin <marcheu@chromium.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Oversight from my kerneldoc cleanup when doing the original atomic
helper series - I've only applied this clarification to the modeset
related helpers, and not the plane update code. Remedy this asap.
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NRob Clark <robdclark@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

I guess for hysterical raisins this was meant to be the way to read
blob properties. But that's done with the two-stage approach which
uses separate blob kms object and the special-purpose get_blob ioctl.

Shipping userspace seems to have never relied on this, and the kernel
also never put any blob thing onto that property. And nowadays it
would blow up, e.g. in drm_property_destroy. Also it makes no sense to
return values in an ioctl that only returns metadata about everything.

So let's ditch all the internal code for the blob list, rename the
list to be unambiguous and sprinkle comments all over the place to
explain this peculiar piece of api.

v2: Squash in fixup from Rob to remove now unused variables.

Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NRob Clark <robdclark@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- Make it clear that it's a negative errno (more in line with
  everything else).
- Clean up the confusion around get_properties vs. getproperty ioctls:
  One reads per-obj property values, the other reads property
  metadata.
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NRob Clark <robdclark@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Yet another fallout from not considering DP MST hotplug. With the
previous patches we have stable indices, but it might still happen
that a connector gets added between when we allocate the array and
when we actually add a connector. Especially when we back off due to
ww mutex contention or similar issues.

So store the sizes of the arrays in struct drm_atomic_state and double
check them. We don't really care about races except that we want to
use a consistent value, so ACCESS_ONCE is all we need. And if we
indeed notice that we'd overrun the array then just give up and
restart the entire ioctl.
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NRob Clark <robdclark@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Otherwise the connector might have been unplugged and destroyed while
we didn't look. Yet another fallout from DP MST hotplugging that I
didn't consider.

To make sure we get this right add an appropriate WARN_ON to
drm_atomic_state_clear (obviously only when we actually have a state
to clear up). And reorder all the state_clear and backoff calls to
make it work out properly.
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NRob Clark <robdclark@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

I've totally forgotten that with DP MST connectors can now be
hotplugged. And failed to adapt Rob's drm_atomic_state code (which
predates connector hotplugging) to the new realities.

The first step is to make sure that the connector indices used to
access the arrays of pointers are stable. The connection mutex gives
us enough guarantees for that, which means we won't unecessarily block
on concurrent modesets or background probing.

So add a locking WARN_ON and shuffle the code slightly to make sure we
always hold the right lock.
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NRob Clark <robdclark@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Let's make things a bit easier to debug when things go bad (potentially
under console_lock).
Signed-off-by: NRob Clark <robdclark@gmail.com>
Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Andrew Morton wrote:
> On Wed, 12 Nov 2014 13:08:55 +0900 Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> wrote:
>
> > Andrew Morton wrote:
> > > Poor ttm guys - this is a bit of a trap we set for them.
> >
> > Commit a91576d7 ("drm/ttm: Pass GFP flags in order to avoid deadlock.")
> > changed to use sc->gfp_mask rather than GFP_KERNEL.
> >
> > -       pages_to_free = kmalloc(npages_to_free * sizeof(struct page *),
> > -                       GFP_KERNEL);
> > +       pages_to_free = kmalloc(npages_to_free * sizeof(struct page *), gfp);
> >
> > But this bug is caused by sc->gfp_mask containing some flags which are not
> > in GFP_KERNEL, right? Then, I think
> >
> > -       pages_to_free = kmalloc(npages_to_free * sizeof(struct page *), gfp);
> > +       pages_to_free = kmalloc(npages_to_free * sizeof(struct page *), gfp & GFP_KERNEL);
> >
> > would hide this bug.
> >
> > But I think we should use GFP_ATOMIC (or drop __GFP_WAIT flag)
>
> Well no - ttm_page_pool_free() should stop calling kmalloc altogether.
> Just do
>
> 	struct page *pages_to_free[16];
>
> and rework the code to free 16 pages at a time.  Easy.

Well, ttm code wants to process 512 pages at a time for performance.
Memory footprint increased by 512 * sizeof(struct page *) buffer is
only 4096 bytes. What about using static buffer like below?
----------
>From d3cb5393c9c8099d6b37e769f78c31af1541fe8c Mon Sep 17 00:00:00 2001
From: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Date: Thu, 13 Nov 2014 22:21:54 +0900
Subject: [PATCH] drm/ttm: Avoid memory allocation from shrinker functions.

Commit a91576d7 ("drm/ttm: Pass GFP flags in order to avoid
deadlock.") caused BUG_ON() due to sc->gfp_mask containing flags
which are not in GFP_KERNEL.

  https://bugzilla.kernel.org/show_bug.cgi?id=87891

Changing from sc->gfp_mask to (sc->gfp_mask & GFP_KERNEL) would
avoid the BUG_ON(), but avoiding memory allocation from shrinker
function is better and reliable fix.

Shrinker function is already serialized by global lock, and
clean up function is called after shrinker function is unregistered.
Thus, we can use static buffer when called from shrinker function
and clean up function.
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@kernel.org> [2.6.35+]
Signed-off-by: NDave Airlie <airlied@redhat.com>

sizeof(u8) is always 1.
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Commit f9b9faf6d94dd29eab8c128905c7d091f955481d "drm: flip-work: change
drm_flip_work_init prototype" changed the drm_flip_work_init prototype
to a void function, which makes 'ret' an unused variable.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Implement crtc page_flip callback for bochsdrm.  The qemu stdvga has no
vblank signaling, so we have to fake it.  We do so by instantly calling
drm_send_vblank_event.  Tested with kmscon.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Remove the mapping offset from the bo backing the fbdev framebuffer.
Wire up fbdev mmap function to map the backing bo using ttm_fbdev_mmap.
With that patch in place mmap(/dev/fb0) works as expected.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Recently (qemu 2.2+) the qemu stdvga got a register to switch the vga
framebuffer endianness.  This patch adds code to explicitly set the
endianness of the framebuffer.  In most cases this has no effect as
the default is guest architecture endianness.  It is needed though in
case a architecture supports both big and little endian, i.e. for
ppc64le.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Drop some leftover, commented code.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Main pull for 3.19.  I may have another pull in a few days with some
mdp5 bits (and hopefully mdp5 atomic), but I figured there was no need
to hold up what we have already.  Main highlights so far:

1) a4xx gpu support (userspace gallium bits on mesa master)
2) mdp4/hdmi/core bits for atomic helpers.  Still missing mdp5
conversion, main hold up there is current hard-coded mixer setup isn't
clever enough to deal with disabling primary plane while crtc active.
3) various other misc cleanup/fixes/etc..

* 'msm-next' of git://people.freedesktop.org/~robclark/linux: (21 commits)
  drm/msm: a4xx support for msm-drm
  drm/msm: Handle register offset differences between a3xx and a4xx
  drm/msm: small mmap offset cleanups
  drm/msm/mdp4: atomic
  drm/msm/hdmi: atomic
  drm/msm: atomic core bits
  drm/msm: bit of fb error checking
  drm/msm: fb prepare/cleanup
  drm/msm: remove unused compile-test stub
  drm/msm: small fence cleanup
  drm/msm/mdp5: drop attached planes table
  drm/msm/mdp4: drop attached planes table
  drm/msm/mdp4: don't care about fb in crtc
  drm/msm/mdp5: drop private primary ptr
  drm/msm/mdp4: drop private primary ptr
  drm/msm: Fix fbdev for 16- and 24-bit modes.
  drm/msm: Allow exported dma-bufs to be mapped
  drm/msm/hdmi: refactor bind/init
  drm/msm: update generated headers
  drm/msm/adreno: slight init order cleanup
  ...