We enable only if the we support 16MB page size.
Reviewed-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We find all the overlapping vma and mark them such that we don't allocate
hugepage in that range. Also we split existing huge page so that the
normal page hash can be invalidated and new page faulted in with new
protection bits.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

With THP we set pmd to none, before we do pte_clear. Hence we can't
walk page table to get the pte lock ptr and verify whether it is locked.
THP do take pte lock before calling pte_clear. So we don't change the locking
rules here. It is that we can't use page table walking to check whether
pte locks are held with THP.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

GCC is very likely to read the pagetables just once and cache them in
the local stack or in a register, but it is can also decide to re-read
the pagetables. The problem is that the pagetable in those places can
change from under gcc.

With THP/hugetlbfs the pmd (and pgd for hugetlbfs giga pages) can
change under gup_fast. The pages won't be freed untill we finish
gup fast because we have irq disabled and we free these pages via
rcu callback.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We need to have irqs disabled to handle all the possible parallel update for
linux page table without holding locks.

Events that we are intersted in while walking page tables are
1) Page fault
2) umap
3) THP split
4) THP collapse

A) local_irq_disabled:
------------------------
1) page fault:
A none to valid transition via page fault is not an issue because we
would either see a none or valid. If it is none, we would error out
the page table walk. We may need to use on stack values when checking for
type of page table elements, because if we do

if (!is_hugepd()) {
    if (!pmd_none() {
       if (pmd_bad() {

We could take that bad condition because the pmd got converted to a hugepd
after the !is_hugepd check via a hugetlb fault.

The right way would be to check for pmd_none higher up or use on stack value.

2) A valid to none conversion via unmap:
We can safely walk the upper level table, because we don't remove the the
page table entries until rcu grace period. So even if we followed a
wrong pointer we still have the pointer valid till the grace period.

A PTE pointer returned need to be atomically checked for _PAGE_PRESENT and
 _PAGE_BUSY. A valid pointer returned could becoming none later. To prevent
pte_clear we take _PAGE_BUSY.

3) THP split:
A valid transparent hugepage is converted to nomal page. Before we split we
do pmd_splitting_flush, which sets the hugepage PTE to _PAGE_SPLITTING
So when walking page table we need to check for pmd_trans_splitting and
handle that. The pte returned should also need to be checked for
_PAGE_SPLITTING before setting _PAGE_BUSY similar to _PAGE_PRESENT. We save
the value of PTE on stack and check for the flag in the local pte value.
If we don't have the value set we can safely operate on the local pte value
and we atomicaly set _PAGE_BUSY.

4) THP collapse:
A normal page gets converted to hugepage. In the collapse path, we
mark the pmd none early (pmdp_clear_flush). With irq disabled, if we
are aleady walking page table we would see the pmd_none and won't continue.
If we see a valid PMD, we should still check for _PAGE_PRESENT before
setting _PAGE_BUSY, to make sure we didn't collapse the PTE to a Huge PTE.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The deposted PTE page in the second half of the PMD table is used to
track the state on hash PTEs. After updating the HPTE, we mark the
coresponding slot in the deposted PTE page valid.
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We can find pte that are splitting while walking page tables. Return
None pte in that case.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Replace find_linux_pte with find_linux_pte_or_hugepte and explicitly
document why we don't need to handle transparent hugepages at callsites.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Reviewed-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We will use this in the later patch for handling THP pages
Reviewed-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We now have pmd entries covering 16MB range and the PMD table double its original size.
We use the second half of the PMD table to deposit the pgtable (PTE page).
The depoisted PTE page is further used to track the HPTE information. The information
include [ secondary group | 3 bit hidx | valid ]. We use one byte per each HPTE entry.
With 16MB hugepage and 64K HPTE we need 256 entries and with 4K HPTE we need
4096 entries. Both will fit in a 4K PTE page. On hugepage invalidate we need to walk
the PTE page and invalidate all valid HPTEs.

This patch implements necessary arch specific functions for THP support and also
hugepage invalidate logic. These PMD related functions are intentionally kept
similar to their PTE counter-part.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

THP code does PTE page allocation along with large page request and deposit them
for later use. This is to ensure that we won't have any failures when we split
hugepages to regular pages.

On powerpc we want to use the deposited PTE page for storing hash pte slot and
secondary bit information for the HPTEs. We use the second half
of the pmd table to save the deposted PTE page.
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If a hash bucket gets full, we "evict" a more/less random entry from it.
When we do that we don't invalidate the TLB (hpte_remove) because we assume
the old translation is still technically "valid". This implies that when
we are invalidating or updating pte, even if HPTE entry is not valid
we should do a tlb invalidate. With hugepages, we need to pass the correct
actual page size value for tlb invalidation.

This change update the patch 0608d692
"powerpc/mm: Always invalidate tlb on hpte invalidate and update" to handle
transparent hugepages correctly.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch creates debugfs entries (powerpc/PCIxxxx/err_injct) for
injecting EEH errors for testing purpose.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch creates one debugfs directory ("powerpc/PCIxxxx") for
each PHB so that we can hook EEH error injection debugfs entry
there in proceeding patch.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch registers OPAL event notifier and process the PCI errors
from firmware. If we have pending PCI errors, special EEH event
(without binding PE) will be sent to EEH core for processing.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

While we're restarting or powering off the system, we needn't
the OPAL notifier any more. So just to disable that.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch implements a notifier to receive a notification on OPAL
event mask changes. The notifier is only called as a result of an OPAL
interrupt, which will happen upon reception of FSP messages or PCI errors.
Any event mask change detected as a result of opal_poll_events() will not
result in a notifier call.

[benh: changelog]
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

It's meaningless to handle frozen PE if we already had fenced PHB.
The patch intends to check the PHB state before checking PE. If the
PHB has been put into fenced state, we need take care of that firstly.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch enables EEH check and let EEH core to process the EEH
errors for PowerNV platform while accessing config space. Originally,
the implementation already had mechanism to check EEH errors and
tried to recover from them. However, we never let EEH core to handle
the EEH errors.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch initializes EEH for PowerNV platform. Because the OPAL
APIs requires HUB ID, we need trace that through struct pnv_phb.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch adds EEH backends for PowerNV platform. It's notable that
part of those EEH backends call to the I/O chip dependent backends.

[Removed pointless change to eeh_pseries.c -- BenH]
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch implements the backend for EEH core to retrieve next
EEH error to handle. For the informational errors, we won't bother
the EEH core. Otherwise, the EEH should take appropriate actions
depending on the return value:

	0 - No further errors detected
	1 - Frozen PE
	2 - Fenced PHB
	3 - Dead PHB
	4 - Dead IOC
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch adds backends to retrieve error log and configure p2p
bridges for the indicated PE.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch adds the I/O chip backend to do PE reset. For now, we
focus on PCI bus dependent PE. If PHB PE has been put into error
state, the PHB will take complete reset. Besides, the root bridge
will take fundamental or hot reset accordingly if the indicated
PE locates at the toppest of PCI hierarchy tree. Otherwise, the
upstream p2p bridge will take hot reset.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch adds I/O chip backend to retrieve the state for the
indicated PE. While the PE state is temperarily unavailable,
the upper layer (powernv platform) should return default delay
(1 second).
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch adds the backend to enable or disable EEH functionality
for the specified PE. The backend is also used to enable MMIO or
DMA path for the problematic PE. It's notable that all PEs on
PowerNV platform support EEH functionality by default, and we
disallow to disable EEH for the specific PE.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The post initialization (struct eeh_ops::post_init) is called after
the EEH probe is done. On the other hand, the EEH core post
initialization is designed to call platform and then I/O chip backend
on PowerNV platform.

The patch adds the backend for I/O chip to notify the platform
that the specific PHB is ready to supply EEH service.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

For EEH on PowerNV platform, the overall architecture is different
from that on pSeries platform. In order to support multiple I/O chips
in future, we split EEH to 3 layers for PowerNV platform: EEH core,
platform layer, I/O layer. It would give EEH implementation on PowerNV
platform much more flexibility in future.

The patch adds the EEH backend for P7IOC.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch synchronizes OPAL APIs between kernel and firmware. Also,
we starts to replace opal_pci_get_phb_diag_data() with the similar
opal_pci_get_phb_diag_data2() and the former OPAL API would return
OPAL_UNSUPPORTED from now on.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

On PowerNV platform, the EEH event caused by interrupt won't have
binding PE. The patch enables EEH core to handle the special event.
To avoid the current logic we have, The eeh_handle_event() is renamed
to eeh_handle_normal_event(), and the eeh_handle_special_event() is
introduced. The function eeh_handle_event() dispatches to above two
functions according to the input parameter. Besides, new backend
"next_error" added to eeh_ops and it's expected to have following
return values:

        4 - Dead IOC           3 - Dead PHB
        2 - Fenced PHB         1 - Frozen PE
        0 - No error found
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

An EEH event is created and queued to the event queue for each
ingress EEH error. When there're mutiple EEH errors, we need serialize
the process to keep consistent PE state (flags). The spinlock
"confirm_error_lock" was introduced for the purpose. We'll inject
EEH event upon error reporting interrupts on PowerNV platform. So
we export the spinlock for that to use for consistent PE state.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

On PowerNV platform, we might run into the situation where subsequent
events are duplicated events of former one, which is being processed.
For the case, we need the function implemented by the patch to purge
EEH events accordingly.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We're not expecting that one specific PE got frozen for over 5
times in last hour. Otherwise, the PE will be removed from the
system upon newly coming EEH errors. The patch introduces time
stamp to trace the first error on specific PE in last hour and
function to update that accordingly. Besides, the time stamp
is recovered during PE hotplug path as we did for frozen count.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We possiblly have multiple kthreads running for multiple EEH errors
(events) and use one spinlock to make the process of handling those
EEH events serialized. That's unnecessary and the patch creates only
one kthread, which is started during EEH core initialization time in
eeh_init(). A new semaphore introduced to count the number of existing
EEH events in the queue and the kthread waiting on the semaphore.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

While doing EEH recovery, the PCI devices of the problematic PE
should be removed and then added to the system again. During the
so-called hotplug event, the PCI devices of the problematic PE
will be probed through early/late phase. We would delay EEH probe
on late point for PowerNV platform since the PCI device isn't
available in early phase.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We shouldn't check that the returned PE status is exactly equal to
(EEH_STATE_MMIO_ACTIVE | EEH_STATE_DMA_ACTIVE) but instead only check
that they are both set.

[benh: changelog]
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch adds new EEH operation post_init. It's used to notify
the platform that EEH core has completed the EEH probe. By that,
PowerNV platform starts to use the services supplied by EEH
functionality.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

For EEH on PowerNV platform, we will do EEH probe based on the
real PCI devices. The PCI devices are available after PCI probe.
So we have to call eeh_init() explicitly on PowerNV platform
after PCI probe. The patch also does EEH probe for PowerNV platform
in eeh_init().
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>