Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 09 1月, 2010 2 次提交
    • C
      omap: gpio: Simultaneously requested rising and falling edge · 4318f36b
      由 Cory Maccarrone 提交于 
      Some chips, namely any OMAP1 chips using METHOD_MPUIO,
OMAP15xx and OMAP7xx, cannot be setup to respond to on-chip GPIO
interrupts in both rising and falling edge directions -- they can
only respond to one direction or the other, depending on how the
ICR is configured.

Additionally, current code forces rising edge detection if both
flags are specified:

        if (trigger & IRQ_TYPE_EDGE_RISING)
                l |= 1 << gpio;
        else if (trigger & IRQ_TYPE_EDGE_FALLING)
                l &= ~(1 << gpio);
        else
                goto bad;

This change implements a toggle function that will modify the ICR
to flip the direction of interrupt for IRQs that are requested with
both rising and falling flags.  The toggle function is not called
for chips and GPIOs it does not apply to through the use of a flip_mask
that's added on a per-bank basis.  The mask is only set for those
GPIOs where a toggle is necessary.  Edge detection starts out the
same as above with FALLING mode first.

The toggle happens on EACH interrupt; without it, we have the
following sequence of actions on GPIO transition:

  ICR    GPIO               Result
  0x1    0 -> 1 (rising)    Interrupt
  0x1    1 -> 0 (falling)   No interrupt

  (set ICR to 0x0 manually)
  0x0    0 -> 1 (rising)    No interrupt
  0x0    1 -> 0 (falling)   Interrupt

That is, with the ICR set to 1 for a gpio, only rising edge interrupts
are caught, and with it set to 0, only falling edge interrupts are
caught.  If we add in the toggle, we get this:

  ICR    GPIO               Result
  0x1    0 -> 1 (rising)    Interrupt (ICR set to 0x0)
  0x0    1 -> 0 (falling)   Interrupt (ICR set to 0x1)
  0x1    0 -> 1 ...

so, both rising and falling are caught, per the request for both
(IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING).
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      4318f36b
    • J
      omap: McBSP: Fix possible port lockout · 1866b545
      由 Janusz Krzysztofik 提交于 
      In its current form, the omap_mcbsp_request() function can return after
irq_request() failure without any cleanups, effectively locking out the port
forever with clocks left running. Fix it.
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      1866b545
  3. 06 1月, 2010 5 次提交
  5. 05 1月, 2010 16 次提交
  7. 04 1月, 2010 12 次提交
  9. 03 1月, 2010 5 次提交