A switch port mode is defined by the association of its egress mode, its
frame mode and if supported or required, the ether type value.

Pack all this in a mv88e6xxx_set_port_mode function and provide helpers
for the Normal Network mode, the DSA mode, and the Ether Type DSA mode,
as well as an helper to setup a port's mode depending on its nature.

Define PORT_ETH_TYPE_DEFAULT for the 0x9100 reset value of port E Type.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not all Marvell switch chips support port trunking, which is embedded in
the port vector data for ATU operations.

Rename the portv_trunkid member of the mv88e6xxx_atu_entry structure to
portvec to be more concise and consistent with the different chips.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename the _mv88e6xxx_fid_new helper to mv88e6xxx_atu_new to get rid of
the old underscore prefix naming convention and be consistent with the
rest of the chip-wide ATU API.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a fresh documented implementation of the ATU Move operation, and use
it to replace the current ATU Remove operation.

Note that not all Marvell switch chip support the ATU Move operation.
For those supporting it, the number of bits used to mask the destination
port may vary. 6352 and such use 4-bit, while 6390 use 5-bit. Thus add a
new atu_move_port_mask member in the info structure to describe the
presence and variant of ATU Move operation.

Note that the ATU Move operation is not documented in the 6185 datasheet
but the chip does support the operation.

All remaining _mv88e6xxx_atu_* functions are now unused as well as the
MV88E6XXX_FLAG_G1_ATU_FID flag, thus remove them.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a fresh documented implementation of the ATU Flush/Move operation.
Use it to replace the current ATU Flush operation.

_mv88e6xxx_atu_flush_move is still used by the Move operation so keep it
until the Move operation is refactored in a next commit.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add and use a fresh documented implementation of the ATU GetNext.

Since it is not necessary to write the MAC address to iterate from, only
do it once directly in the ATU GetNext operation, if the provided ATU
entry structure is not valid. This makes the user code simpler.

Also, there is no need to loop when getting a single ATU entry. So
remove the mv88e6xxx_atu_get helper and add a simpler snippet in
mv88e6xxx_port_db_load_purge to lookup a given MAC address.

The _mv88e6xxx_atu_mac_{read,write} are not used anymore thus remove
them. _mv88e6xxx_atu_data_{read,write} are still used so keep them.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All Marvell switch chips have an ATU accessed using the same Global (1)
register layout. Only the handling of the FID differs as more bits were
necessary to support more and more databases.

Add and use a fresh documented implementation of the ATU Load/Purge.

The static mv88e6xxx_g1_atu_{fid_write,op_wait,op,data_write,mac_write}
functions won't need to be exposed in the end so for the moment keep
their counterparts _mv88e6xxx_atu_{wait,cmd,data_write,mac_write} as is,
since they are still used by other ATU operations.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ATU Learn2All feature allows newly learnt addresses to be spanned on
ports marked as "Message Port", currently all DSA ports.

This commit enables this feature which is necessary and quite convenient
for multi-chip switch fabrics.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All interconnectable Marvell switch chips have an ATU Learn2All feature
which allows newly learnt addresses to be spanned on ports marked as
"Message Port".

This commit configures the DSA ports as Message Port. Note that this has
no effect until the Learn2All feature is enabled.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the configuration of the default ageing time in a new
mv88e6xxx_atu_setup function.

That function will be extended later to contain all ATU related
configuration bits.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the ATU ageing time setter code in a new global1_atu.c file, which
will be extended in future patches to contains all consequent Global (1)
ATU support code.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a mv88e6xxx_port_mask() helper to get the bitmask of ports in a
switch chip, that will be used in several features.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for TC flower offload statistics including number of packets,
bytes and last use timestamp. Currently the statistics are gathered on a
per-rule basis.
Signed-off-by: NArkadi Sharshvesky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for packets and byte statistics on TCAM entries. The counters
are allocated from the generic flow counters pool.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for Policing and Counting action block. This action block
will be used to bind counter to TCAM entries.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce periodic task for dumping the activity status for the ACL
rule TCAM entries. This is done in order to emulate last use statistics.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.comi>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the ACL rules can be accessed only by hashing. In order to
dump the activity the rules are also placed in a list.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for retrieving TCAM entry activity. In order to support ACL
rule activity corresponding TCAM entry should be queried.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for allocating generic flow counter. Generic flow counter
can count packets or packets and bytes and can be assigned to different
hardware processes. First use will be for counting packets and bytes of
ACL rules, and will be introduced in the following patches.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MGPC register retrieves generic flow counter value. It will be
used to query ACL counters.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add implementation for counter allocator. The ASIC has special memory
pool for various counting purposes. Counter memory is distributed between
equal size banks.

The static sub-pool configuration should specify the following parameters
for each sub-pool:
- Number of required banks.
- Maximum entry size.

Each module can add dedicated sub-pool or use existing one.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: NGeliang Tang <geliangtang@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support prepending data from XDP.  We are already always allocating
some headroom because FW may prepend metadata to packets.
xdp_adjust_head() can be supported by making sure that headroom is
big enough for XDP.  In case FW had prepended metadata to the packet,
however, we have to move it out of the way before we call XDP.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

XDP may require us to move metadata to make room for pushing
headers.  Track meta data location with a pointer and pass
it explicitly to functions.

While at it validate that meta_len from the descriptor is not
bogus.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename pkt_off variable to dma_off, it should hold data offset
counting from beginning of DMA mapping.  Compute the value only
in XDP context.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NFP_NET_CFG_RX_OFFSET is 32bit wide, make sure what we read from
there is reasonable for packet headroom.  This allows us to store
the rx_offset in a 8bit variable.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of testing if xdp_prog is present store the dma direction
in data path structure.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of passing around sets of rings and their parameters just
store all information in the data path structure.

We will no longer user xchg() on XDP programs when we swap programs
while the traffic is guaranteed not to be flowing.  This allows us
to simply assign the entire data path structures instead of copying
field by field.

The optimization to reallocate only the rings on the side (RX/TX)
which has been changed is also removed since it seems like it's not
worth the code complexity.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use xdp_prog member of data path struct to carry the xdp_prog to
alloc/free free functions.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the mtu member from ring set to data path struct.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use fl_bufsz member of data path struct to carry desired size of
free list entries.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of passing variables around use dp to store number of tx rings
for the stack and number of IRQ vectors.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make callers of nfp_net_ring_reconfig() pass newly allocated data
path structure.  We will gradually make use of that structure
instead of passing parameters around to all the allocation functions.
This commit adds allocation and propagation of new data path struct,
no parameters are converted, yet.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Control BAR pointer is used to unmask interrupts so it should be
in the first cacheline of adapter structure.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move all data path information into a separate structure.  This way
we will be able to allocate new data path with all new rings etc.
and swap it in easily.

No functional changes.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the configuration of the AVB Credit-Based Shaper.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares mac debug dump for multiple queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares mac irq status treatment for multiple queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adapts flow_ctrl function to prepare it for multiple queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the functionality of RX queue to dma channel mapping
based on configuration.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>