No need to return a 'fake' return value on platform_get_irq() failure.

Just return the error code itself instead.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes it possible to set the chipidea udc into full-speed only mode.
It is set by the oftree property "maximum-speed = full-speed".
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the wrapper function for retrieving the platform data instead
of accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

- delete the warning message at interrupt handler, and adds judgement at
ep_enable, if non-ep0 requests ctrl transfer, it will indicate an error.
- delete hw_test_and_clear_setup_status which is a broken code
- Tested with g_mass_storage, g_ncm, g_ether

Cc: matthieu.castet@parrot.com
Reported-by: NMichael Grzeschik <mgr@pengutronix.de>
Acked-by: NMichael Grzeschik <mgr@pengutronix.de>
Tested-by: NMichael Grzeschik <mgr@pengutronix.de>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

- Delete global_phy due to we can get the phy from phy layer now
- using devm_usb_get_phy to instead of usb_get_phy
- delete the otg_set_peripheral, which should be handled by otg layer
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

ENDPTFLUSH and ENDPTPRIME registers are set by software and clear
by hardware. There is a bit for each endpoint. When we are setting
a bit for an endpoint we should make sure we do not touch other
endpoint bit. There is a race condition if the hardware clear the
bit between the read and the write in hw_write.

Cc: stable <stable@vger.kernel.org> # 3.11+
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NMatthieu CASTET <matthieu.castet@parrot.com>
Tested-by: NMichael Grzeschik <mgrzeschik@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

schedule_delayed_work() takes the delay in jiffies, not msecs.

This bug slipped in with the recent reset logic cleanup
(8ed1fb79: "usb: musb: finish suspend/reset work independently from
musb_hub_control()").
Signed-off-by: NDaniel Mack <daniel@zonque.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Both the PM_RUNTIME and PM_SLEEP callbacks call into the common
msm_otg_{suspend,resume} routines, however these routines are only being
built when CONFIG_PM_SLEEP.  In addition, msm_otg_{suspend,resume} also
depends on msm_hsusb_config_vddcx(), which is only built when
CONFIG_PM_SLEEP.

Fix the CONFIG_PM_RUNTIME, !CONFIG_PM_SLEEP case by changing the
preprocessor conditional, and moving msm_hsusb_config_vddcx().

While we're here, eliminate the CONFIG_PM conditional for setting
up the dev_pm_ops.

This address the following errors Russell King has hit doing randconfig
builds:

drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_suspend':
drivers/usb/phy/phy-msm-usb.c:1691:2: error: implicit declaration of function 'msm_otg_suspend'
drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_resume':
drivers/usb/phy/phy-msm-usb.c:1699:2: error: implicit declaration of function 'msm_otg_resume'

Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NJosh Cartwright <joshc@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix possible NULL pointer dereference introduced in
commit 219580e6 (usb: f_fs: check quirk to pad epout
buf size when not aligned to maxpacketsize)

In cases we do wait with:

wait_event_interruptible(epfile->wait, (ep = epfile->ep));

for endpoint to be enabled, functionfs_bind() has not been called yet
and epfile->ffs->gadget is still NULL and the automatic variable 'gadget'
has been initialized with NULL at the point of its definition.
Later on it is used as a parameter to:

usb_ep_align_maybe(gadget, ep->ep, len)

which in turn dereferences it.

This patch fixes it by moving the actual assignment to the local 'gadget'
variable after the potential waiting has completed.
Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We need to use gadget_is_otg to check if the gadget is really
otg support at runtime, other composite gadget drivers have already
followed this method.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

USB_ARCH_HAS_EHCI, USB_ARCH_HAS_OHCI, and USB_ARCH_HAS_XHCI were made
obsolete in v3.11. They have not been used ever since. Setting them has
no effect. They can safely be removed.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

schedule_delayed_work() takes the delay in jiffies, not msecs. Fix the
caller sites in musb. This bug caused regressions with the cleanups
that went in for 3.14 (8ed1fb79: "usb: musb: finish suspend/reset
work independently from musb_hub_control()").
Signed-off-by: NDaniel Mack <daniel@zonque.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

musb_port_reset() is called from musb_hub_control() which in turn holds
a spinlock, so musb_port_reset() is not allowed to call msleep().

With the asynchronous work helpers in place, this is fortunately easy to
fix by rescheduling the reset deassertion function to after the time
when the wait period is finished.

Note, however, that the MUSB_POWER_RESUME bit is only set on AM33xx
processors under rare conditions such as when to another driver
reporting an error during suspend. Hence, this didn't hit me yet in
normal operation.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This interface is to be handled by the qmi_wwan driver.

CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: NAleksander Morgado <aleksander@aleksander.es>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

High-speed USB connections revert back to full-speed signalling when
the device goes into suspend.  This takes several milliseconds, and
during that time it's not possible to tell reliably whether the device
has been disconnected.

On some platforms, the Wake-On-Disconnect circuitry gets confused
during this intermediate state.  It generates a false wakeup signal,
which can prevent the controller from going to sleep.

To avoid this problem, this patch adds a 5-ms delay to the
ehci_bus_suspend() routine if any ports have to switch over to
full-speed signalling.  (Actually, the delay was already present for
devices using a particular kind of PHY power management; the patch
merely causes the delay to be used more widely.)
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reviewed-by: NPeter Chen <Peter.Chen@freescale.com>
CC: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 3dc6475c ("bcm63xx_enet: add support Broadcom BCM6345 Ethernet")
changed the ENETDMA[CS] macros such that they are no longer macros, but
actual register offset definitions. The bcm63xx_udc driver was not
updated, and as a result, causes the following build error to pop up:

 CC      drivers/usb/gadget/u_ether.o
drivers/usb/gadget/bcm63xx_udc.c: In function 'iudma_write':
drivers/usb/gadget/bcm63xx_udc.c:642:24: error: called object '0' is not
a function
drivers/usb/gadget/bcm63xx_udc.c: In function 'iudma_reset_channel':
drivers/usb/gadget/bcm63xx_udc.c:698:46: error: called object '0' is not
a function
drivers/usb/gadget/bcm63xx_udc.c:700:49: error: called object '0' is not
a function

Fix this by updating usb_dmac_{read,write}l and usb_dmas_{read,write}l to
take an extra channel argument, and use the channel width
(ENETDMA_CHAN_WIDTH) to offset the register we want to access, hence
doing again what the macro implicitely did for us.

Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

musb_port_reset() is called from musb_hub_control() which in turn holds
a spinlock, so musb_port_reset() is not allowed to call msleep().

With the asynchronous work helpers in place, this is fortunately easy to
fix by rescheduling the reset deassertion function to after the time
when the wait period is finished.

Note, however, that the MUSB_POWER_RESUME bit is only set on AM33xx
processors under rare conditions such as when to another driver
reporting an error during suspend. Hence, this didn't hit me yet in
normal operation.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Pass value instead of address as expected by 'usb_ep_set_maxpacket_limit'.
Fixes the following compilation error introduced by commit e117e742
("usb: gadget: add "maxpacket_limit" field to struct usb_ep"):

drivers/usb/gadget/s3c2410_udc.c: In function ‘s3c2410_udc_reinit’:
drivers/usb/gadget/s3c2410_udc.c:1632:3: error:
cannot take address of bit-field ‘maxpacket’
   usb_ep_set_maxpacket_limit(&ep->ep, &ep->ep.maxpacket);
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

During resume don't touch SUSPENDM/RESUME bits of POWER register
while restoring controller context. These bits might be changed
by the controller during resume operation and so will be different
than what they were during suspend.

e.g. SUSPENDM bit is set by software during USB global suspend but
automatically cleared by the controller during remote wakeup or
during resume. Setting this bit back while restoring context
causes undesired behaviour. i.e. Babble interrupt is generated
and USB is broken.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Disables PING on status phase of control transfer.
PING token is not mandatory in status phase of control transfer
and so some high speed USB devices don't support it. If such devices
are connected to MUSB then they would not respond to PING token
causing delayed or failed enumeration.

[Roger Q] Fixes enumeration issues with some Super-Speed USB hubs
e.g. Dlink DUB-1340
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

phy_power_off() can, depending on the PHY being used,
start I2C transactions which shouldn't happen in
atomic context.

Current call to phy_power_off() inside omap2430_runtime
callbacks causes the following dump, as a fix, just don't
power off the PHY in runtime.

[   18.606414] [<c037eac0>] (__schedule+0x5c/0x50c) from [<c037d3bc>] (schedule_timeout+0x1f4/0x25c)
[   18.623809] [<c037d3bc>] (schedule_timeout+0x1f4/0x25c) from [<c037f12c>] (wait_for_common+0xc8/0x1ac)
[   18.649291] [<c037f12c>] (wait_for_common+0xc8/0x1ac) from [<c028c1c0>] (omap_i2c_xfer+0x338/0x488)
[   18.674499] [<c028c1c0>] (omap_i2c_xfer+0x338/0x488) from [<c0288144>] (__i2c_transfer+0x40/0x74)
[   18.692047] [<c0288144>] (__i2c_transfer+0x40/0x74) from [<c0288a2c>] (i2c_transfer+0x6c/0x90)
[   18.709320] [<c0288a2c>] (i2c_transfer+0x6c/0x90) from [<c02351c8>] (regmap_i2c_read+0x48/0x68)
[   18.726715] [<c02351c8>] (regmap_i2c_read+0x48/0x68) from [<c023161c>] (_regmap_raw_read+0x128/0x220)
[   18.752685] [<c023161c>] (_regmap_raw_read+0x128/0x220) from [<c02317b4>] (regmap_raw_read+0xa0/0x130)
[   18.779052] [<c02317b4>] (regmap_raw_read+0xa0/0x130) from [<c023193c>] (regmap_bulk_read+0xf8/0x16c)
[   18.805694] [<c023193c>] (regmap_bulk_read+0xf8/0x16c) from [<c0238ea8>] (twl_i2c_read+0xa4/0xe0)
[   18.823730] [<c0238ea8>] (twl_i2c_read+0xa4/0xe0) from [<c0274d34>] (__twl4030_phy_power.isra.12+0x1c/0x58)
[   18.850921] [<c0274d34>] (__twl4030_phy_power.isra.12+0x1c/0x58) from [<c0274df0>]
(twl4030_phy_power.part.14+0x80/0xc8)
[   18.879699] [<c0274df0>] (twl4030_phy_power.part.14+0x80/0xc8) from [<c0274f9c>]
(twl4030_set_suspend+0x54/0x1e8)
[   18.908325] [<c0274f9c>] (twl4030_set_suspend+0x54/0x1e8) from [<c027c8c4>]
(omap2430_runtime_resume+0x5c/0x64)
[   18.937042] [<c027c8c4>] (omap2430_runtime_resume+0x5c/0x64) from [<c0225dd0>]
(pm_generic_runtime_resume+0x2c/0x38)
[   18.966461] [<c0225dd0>] (pm_generic_runtime_resume+0x2c/0x38) from [<c0229fe0>] (__rpm_callback+0x54/0x80)
[   18.995117] [<c0229fe0>] (__rpm_callback+0x54/0x80) from [<c022a04c>] (rpm_callback+0x40/0x74)
[   19.013610] [<c022a04c>] (rpm_callback+0x40/0x74) from [<c022b3c8>] (rpm_resume+0x448/0x63c)
[   19.031921] [<c022b3c8>] (rpm_resume+0x448/0x63c) from [<c022b2e4>] (rpm_resume+0x364/0x63c)
[   19.050140] [<c022b2e4>] (rpm_resume+0x364/0x63c) from [<c022b874>] (__pm_runtime_resume+0x48/0x74)
[   19.077728] [<c022b874>] (__pm_runtime_resume+0x48/0x74) from [<c027b4fc>] (musb_gadget_pullup+0x1c/0xb4)
[   19.105895] [<c027b4fc>] (musb_gadget_pullup+0x1c/0xb4) from [<bf025c14>] (usb_function_deactivate+0x54/0xa4
[libcomposite])
[   19.135955] [<bf025c14>] (usb_function_deactivate+0x54/0xa4 [libcomposite]) from [<bf05b3b8>]
(obex_bind+0x124/0x1d8 [usb_f_obex])
[   19.166870] [<bf05b3b8>] (obex_bind+0x124/0x1d8 [usb_f_obex]) from [<bf025794>] (usb_add_function+0x58/0xf4
[libcomposite])
[   19.197143] [<bf025794>] (usb_add_function+0x58/0xf4 [libcomposite]) from [<bf037420>]
(nokia_bind_config+0x204/0x250 [g_nokia])
[   19.227905] [<bf037420>] (nokia_bind_config+0x204/0x250 [g_nokia]) from [<bf0263fc>] (usb_add_config+0x28/0xc0
[libcomposite])
[   19.258483] [<bf0263fc>] (usb_add_config+0x28/0xc0 [libcomposite]) from [<bf03709c>] (nokia_bind+0x9c/0x21c
[g_nokia])
[   19.288421] [<bf03709c>] (nokia_bind+0x9c/0x21c [g_nokia]) from [<bf0275bc>] (composite_bind+0x74/0x180
[libcomposite])
[   19.318420] [<bf0275bc>] (composite_bind+0x74/0x180 [libcomposite]) from [<c027d658>]
(udc_bind_to_driver+0x2c/0xc4)
[   19.348114] [<c027d658>] (udc_bind_to_driver+0x2c/0xc4) from [<c027d764>] (usb_gadget_probe_driver+0x74/0x94)
[   19.377166] [<c027d764>] (usb_gadget_probe_driver+0x74/0x94) from [<c00086f8>] (do_one_initcall+0x94/0x138)
[   19.406005] [<c00086f8>] (do_one_initcall+0x94/0x138) from [<c007a460>] (load_module+0x113c/0x13c4)
[   19.434051] [<c007a460>] (load_module+0x113c/0x13c4) from [<c007a7b4>] (SyS_init_module+0xcc/0xec)
[   19.462127] [<c007a7b4>] (SyS_init_module+0xcc/0xec) from [<c000dd40>] (ret_fast_syscall+0x0/0x30)
[   19.490753] Code: 0a00002e e1a00004 eb001438 e598300c (e5d3202c)
[   19.506805] ---[ end trace 060b62ec0d68a78b ]---
[   19.523132] Kernel panic - not syncing: Fatal exception in interrupt

dump is from 3.12-rc5 kernel
Reported-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NIvaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In a couple of places, we were checking qtd->urb for NULL after
we had already dereferenced it. Fix this by moving the check to
before the dereference.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This brings the xhci-platform bindings in sync with what we've done for
the ohci- and ehci-platform drivers. As discussed there using platform as a
postfix is a bit weird as the platform bus is a Linux specific thing and
the bindings are supposed to be OS agnostic.

Note that the old xhci-platform compatible string is kept around for, well,
compatibility reasons.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This brings the uhci-platform bindings in sync with what we've done for
the ohci- and ehci-platform drivers. As discussed there using platform as a
prefix is a bit weird as the platform bus is a Linux specific thing and
the bindings are supposed to be OS agnostic.

Note that the old platform-uhci compatible string is kept around for, well,
compatibility reasons.

While at it rename the bindings txt file to match the name of all the
other ?hci-platform bindings docs.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Interface #5 of 19d2:1270 is a net interface which has been submitted to the
qmi_wwan driver so consequently remove it from the option driver.
Signed-off-by: NRaymond Wanyoike <raymond.wanyoike@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for the "Webmail Notifier" (USB powered LED for signaling
new emails) made by Riso Kagaku Corp. which displays 7 distinct colors.

USB Protocol initially reverse engineered by
	https://code.google.com/p/usbmailnotifier/.
Signed-off-by: NChristian Vogel <vogelchr@vogel.cx>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Kconfig entries for USB_U132_HCD and USB_FTDI_ELAN default to
(uppercase) "M". But in Kconfig (lowercase) "m" is a magic symbol. "M"
is an ordinary symbol. As "M" is never set these Kconfig symbols will
also not be set by default.

Since I'm not aware of a reason why these driver should be set by
default, let's just drop these lines (that basically do nothing).
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The symbol is an orphan, get rid of it.
Signed-off-by: NRichard Weinberger <richard@nod.at>
Acked-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The ohci-platform driver checks for misconfigurations in cases where
the Device Tree data specifies big-endian registers or descriptors but
the corresponding driver config settings have not been enabled.  As
Jonas Gorski suggested, we may as well apply the same check to general
platform data too.

This requires moving the code that sets the big-endian quirk flags
from the ohci_platform_reset() routine into ohci_platform_probe(), and
moving the checks out of the DT-specific "if" statement clause.

The patch also changes the text of the error messages in an attempt to
make the nature of the error more clear.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NJonas Gorski <jogo@openwrt.org>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The ehci-platform driver checks for misconfigurations in cases where
the Device Tree data specifies big-endian registers or descriptors but
the corresponding driver config settings have not been enabled.  As
Jonas Gorski suggested, we may as well apply the same check to general
platform data too.

This requires moving the code that sets the big-endian quirk flags
from the ehci_platform_reset() routine into ehci_platform_probe(), and
moving the checks out of the DT-specific "if" statement clause.

The patch also changes the text of the error messages in an attempt to
make the nature of the error more clear.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NJonas Gorski <jogo@openwrt.org>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The initial versions of the devicetree enablement patches for ehci-platform
used "ehci-platform" as compatible string. However this was disliked by various
reviewers because the platform bus is a Linux invention and devicetree is
supposed to be OS agnostic. After much discussion I gave up, added a:
"depends on !PPC_OF" to Kconfig to avoid a known conflict with PPC-OF platforms
and went with the generic usb-ehci as requested.

In retro-spect I should have chosen something different, the dts files for many
existing boards already claim to be compatible with "usb-ehci", ie they have:

	compatible = "ti,ehci-omap", "usb-ehci";

In theory this should not be a problem since the "ti,ehci-omap" entry takes
presedence, but in practice using a conflicting compatible string is an issue,
because it makes which driver gets used depend on driver registration order.

This patch changes the compatible string claimed by ehci-platform to
"generic-ehci", avoiding the driver registration / module loading ordering
problems, and removes the "depends on !PPC_OF" workaround.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The initial versions of the devicetree enablement patches for ohci-platform
used "ohci-platform" as compatible string. However this was disliked by various
reviewers because the platform bus is a Linux invention and devicetree is
supposed to be OS agnostic. After much discussion I gave up and went with
the generic usb-ohci as requested.

In retro-spect I should have chosen something different, the dts files for many
existing boards already claim to be compatible with "usb-ohci", ie they have:

	compatible = "ti,ohci-omap3", "usb-ohci";

In theory this should not be a problem since the "ti,ohci-omap3" entry takes
presedence, but in practice using a conflicting compatible string is an issue,
because it makes which driver gets used depend on driver registration order.

This patch changes the compatible string claimed by ohci-platform to
"generic-ohci", avoiding the driver registration / module loading ordering
problems.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Tested-by: NKevin Hilman <khilman@linaro.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Allow the scheduler to select the best CPU to handle hub initalization
and LED blinking work. This extends idle residency times on idle CPUs
and conserves power.

This functionality is enabled when CONFIG_WQ_POWER_EFFICIENT is selected.

[zoran.markovic@linaro.org: Rebased to latest kernel. Added commit message.
Changed reference from system to power efficient workqueue for LEDs in
check_highspeed() and hub_port_connect_change().]
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Xenia Ragiadakou <burzalodowa@gmail.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Krzysztof Mazur <krzysiek@podlesie.net>
Cc: Matthias Beyer <mail@beyermatthias.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: NShaibal Dutta <shaibal.dutta@broadcom.com>
Signed-off-by: NZoran Markovic <zoran.markovic@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Free "motog" on error.  This is more to appease the static checkers than
a real worry.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

According to the spec for the DWC2 controller, when the PRTINT interrupt fires,
the application must clear the appropriate status bit in the Host Port Control
and Status register to clear this bit.

When disconnecting an A-cable when the dwc2 host driver, the PRTINT fires, but
only the GINTSTS_PRTINT status is cleared, no action is done with the HPRT0
register. The HPRT0_ENACHG bit in the HPRT0 must also be poked to correctly
clear the GINTSTS_PRTINT interrupt.

I am seeing this behavoir on v2.93 of the DWC2 IP. When I disconnect an OTG
A-cable adapter, the PRTINT interrupt fires when the DWC2 is in device mode
and is never cleared.

This patch adds the function to read the HPRT0 register when the PRTINT fires
and the dwc2 IP has already transitioned to device mode. This function is only
clearing the HPRT0_ENACHG bit for now, but can be modified to handle more.
Signed-off-by: NDinh Nguyen <dinguyen@altera.com>
[ paulz: modified patch to preserve HPRT0_ENA bit ]
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 35773dac.  It's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb.  Commit 70cabb7d992f "xhci 1.0: Limit
arbitrarily-aligned scatter gather." should fix the issues seen with the
ax88179_178a driver on xHCI 1.0 hosts, without causing regressions.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org # 3.12

This reverts commit d6c9ea90.

We are ripping out commit 35773dac "usb:
xhci: Link TRB must not occur within a USB payload burst" because it's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb.  This commit attempted to fix the
issues with that patch.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org # 3.12

This reverts commit f2d9b991.

We are ripping out commit 35773dac "usb:
xhci: Link TRB must not occur within a USB payload burst" because it's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb.  This commit attempted to fix the
issues with that patch.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org #3.12

xHCI 1.0 hosts have a set of requirements on how to align transfer
buffers on the endpoint rings called "TD fragment" rules.  When the
ax88179_178a driver added support for scatter gather in 3.12, with
commit 804fad45411b48233b48003e33a78f290d227c8 "USBNET: ax88179_178a:
enable tso if usb host supports sg dma", it broke the device under xHCI
1.0 hosts.  Under certain network loads, the device would see an
unexpected short packet from the host, which would cause the device to
stop sending ethernet packets, even through USB packets would still be
sent.

Commit 35773dac "usb: xhci: Link TRB must not occur within a USB
payload burst" attempted to fix this.  It was a quick hack to partially
implement the TD fragment rules.  However, it caused regressions in the
usb-storage layer and userspace USB drivers using libusb.  The patches
to attempt to fix this are too far reaching into the USB core, and we
really need to implement the TD fragment rules correctly in the xHCI
driver, instead of continuing to wallpaper over the issues.

Disable arbitrarily-aligned scatter-gather in the xHCI driver for 1.0
hosts.  Only the ax88179_178a driver checks the no_sg_constraint flag,
so don't set it for 1.0 hosts.  This should not impact usb-storage or
usbfs behavior, since they pass down max packet sized aligned sg-list
entries (512 for USB 2.0 and 1024 for USB 3.0).
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NMark Lord <mlord@pobox.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Freddy Xin <freddy@asix.com.tw>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: stable@vger.kernel.org # 3.12

This uses the already documented devicetree booleans for this, see:
Documentation/devicetree/bindings/usb/usb-ehci.txt
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>