Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: NTom Herbert <therbert@google.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: NTom Herbert <therbert@google.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

netpoll can call functions in hard irq context that are ordinarily
called in lesser contexts.  For those functions use dev_kfree_skb_any
and dev_consume_skb_any so skbs are freed safely from hard irq
context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace free_skb with dev_kfree_skb_any in be_tx_compl_process as
which can be called in hard irq by netpoll, softirq context
by normal napi polling, and in normal sleepable context
by the network device close method.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace kfree_skb with dev_kfree_skb_any in cp_start_xmit
as it can be called in both hard irq and other contexts.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a VLAN is added by user, adapter->vlans_added is incremented.
But if the VLAN is already programmed in HW, driver ends up
incrementing the counter wrongly.

Increment the counter only if VLAN is not already programmed in the HW.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the driver creates only a single TXQ on any BE3-R multi-channel
interface.
This patch changes this and creates multiple TXQs on RSS-capable multi-channel
BE3-R interfaces. This change helps improve the TX pps performance on the
affected interface.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The allocation size must be be_max_uc() and not "be_max_uc() + 1"
Signed-off-by: NRavikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRavikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to control VF's link state by implementing the
ndo_set_vf_link_state() hook.
Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use GET_PROFILE_CONFIG_V1 cmd even for BE3-R (it's already used for
Lancer-R and Skyhawk-R), to query max-vfs value supported by the FW.
This is needed as on some configs, the value exported in the PCI-config
space is not accurate.
Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To activate RoCE/SRIOV, need to remove the following:
1. In mlx4_ib_add, need to remove the error return preventing
   initialization of a RoCE port under SRIOV.
2. In update_vport_qp_params (in resource_tracker.c) need to remove
   the error return when a RoCE RC or UD qp is detected.
   This error return causes the INIT-to-RTR qp transition to fail
   in the wrapper function under RoCE/SRIOV.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since there is no connection between the MAC/VLAN and the GID
when using IP-based addressing, the proxy QP1 (running on the
slave) must pass the source-mac, destination-mac, and vlan_id
information separately from the GID. Additionally, the Host
must pass the remote source-mac and vlan_id back to the slave,

This is achieved as follows:
Outgoing MADs:
    1. Source MAC: obtained from the CQ completion structure
       (struct ib_wc, smac field).
    2. Destination MAC: obtained from the tunnel header
    3. vlan_id: obtained from the tunnel header.
Incoming MADs
    1. The source (i.e., remote) MAC and vlan_id are passed in
       the tunnel header to the proxy QP1.

VST mode support:
     For outgoing MADs,  the vlan_id obtained from the header is
        discarded, and the vlan_id specified by the Hypervisor is used
        instead.
     For incoming MADs, the incoming vlan_id (in the wc) is discarded, and the
        "invalid" vlan (0xffff)  is substituted when forwarding to the slave.
Signed-off-by: NMoni Shoua <monis@mellanox.co.il>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IB side of RoCE requires the MAC table index of the
MAC address used by its QPs.

To obtain the real MAC index, the IB side registers the
MAC (increasing its ref count, and also returning the
real MAC index) during the modify-qp sequence.

This protects against the ETH side deleting or modifying
that MAC table entry while the QP is active.

Note that until the modify-qp command returns success,
the MAC and VLAN information only has "candidate" status.
If the modify-qp succeeds, the "candidate" info is promoted
to the operational MAC/VLAN info for the qp. If the modify fails,
the candidate MAC/VLAN is unregistered, and the old qp info
is preserved.

The patch is a bit complex, because there are multiple qp
transitions where the primary-path information may be
modified:  INIT-to-RTR, and SQD-to-SQD.

Similarly for the alternate path information.

Therefore the code must handle cases where path information
has already been entered into the QP context by previous
qp transitions.

For the MAC address, the success logic is as follows:
1. If there was no previous MAC, simply move the candidate
   MAC information to the operational information, and reset
   the candidate MAC info.
2. If there was a previous MAC, unregister it.  Then move
   the MAC information from candidate to operational, and
   reset the candidate info (as in 1. above).

The MAC address failure logic is the same for all cases:
 - Unregister the candidate MAC, and reset the candidate MAC info.

For Vlan registration, the logic is similar.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The GIDs are statically distributed, as follows:
PF: gets 16 GIDs
VFs:  Remaining GIDS are divided evenly between VFs activated by the driver.
      If the division is not even, lower-numbered VFs get an extra GID.

For an IB interface, the number of gids per guest remains as before: one gid per guest.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For IB transport, the host determines the slave GIDs. For ETH (RoCE),
however, the slave's GID is determined by the IP address that the slave
itself assigns to the ETH device used by RoCE.

In this case, the slave must be able to write its GIDs to the HCA gid table
(at the GID indices that slave "owns").

This commit adds processing for the SET_PORT_GID_TABLE opcode modifier
for the SET_PORT command wrapper (so that slaves may modify their GIDS
for RoCE).
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This requires the following modifications:
1. Fix build_mlx4_header to properly fill in the ETH fields
2. Adjust mux and demux QP1 flow to support RoCE.

This commit still assumes only one GID per slave for RoCE.
The commit enabling multiple GIDs is a subsequent commit, and
is done separately because of its complexity.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

priv is not instantiated at gfar_of_init() time, when
parsing the DT for info on supported HW queues.  Before
the netdev can be allocated, the number of supported
queues must be known.  Because the number of supported
queues depends on device type, move the compatibility
checks before netdev allocation.  Local vars are used
to hold the operation mode info before netdev allocation.
This fixes the null accesses for priv->.., in gfar_of_init.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add dumping the tally counter by ethtool.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rf233 and rf231 are sufficiently similar that we can treat
rf233 like rf231.

rf233 is missing some features that rf231 has, but we don't currently
make use of them so there's nothing to handle differently yet.

Should we add support in the future for rf231 *_NOCLK or SLEEP states,
or PAD_IO drive strength, exceptions will need to be made for rf233.
Signed-off-by: NThomas Stilwell <stilwellt@openlabs.co>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The option code is taking IP address and putting it into a generic
container. Force cast to silence sparse warnings.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call skb_cow_head() before editing the tx packet header. The header
would be reallocated if it is shared.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using an own copy of struct net_device_stats in struct
cpsw_priv, use stats from struct net_device. Also remove the thus
unnecessary .ndo_get_stats function, as it just returns dev->stats,
which is the default.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to a bug in the Hyper-V host verion 2008R2, we need to use a slightly smaller
receive buffer size, otherwise the buffer will not be accepted by the legacy hosts.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable segmentation offload.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable send side checksum offload.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable receive side checksum offload.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prior to enabling guest side offloads, enable the offloads on the host.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for enabling offloads, cleanup the send path.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>