Use PCI standard marco dev_is_pci() instead of directly compare
pci_bus_type to check whether it is pci device.
Signed-off-by: NYijing Wang <wangyijing@huawei.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In the drivers that no longer need it, it is removed.
It is removed from the Makefile. Drivers not fully converted
to dynamic debug have it shifted down into the individual
drivers.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch continues the scheduling changes in ehci-hcd by adding a
table to store the bandwidth allocation below each TT.  This will
speed up the scheduling code, as it will no longer need to read
through the entire schedule to compute the bandwidth currently in use.

Properly speaking, the FS/LS budget calculations should be done in
terms of full-speed bytes per microframe, as described in the USB-2
spec.  However the driver currently uses microseconds per microframe,
and the scheduling code isn't robust enough at this point to change
over.  For the time being, we leave the calculations as they are.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch significantly changes the scheduling code in ehci-hcd.
Instead of calculating the current bandwidth utilization by trudging
through the schedule and adding up the times used by the existing
transfers, we will now maintain a table holding the time used for each
of 64 microframes.  This will drastically speed up the bandwidth
computations.

In addition, it eliminates a theoretical bug.  An isochronous endpoint
may have bandwidth reserved even at times when it has no transfers
listed in the schedule.  The table will keep track of the reserved
bandwidth, whereas adding up entries in the schedule would miss it.

As a corollary, we can keep bandwidth reserved for endpoints even
when they aren't in active use.  Eventually the bandwidth will be
reserved when a new alternate setting is installed; for now the
endpoint's reservation takes place when its first URB is submitted.

A drawback of this approach is that transfers with an interval larger
than 64 microframes will have to be charged for bandwidth as though
the interval was 64.  In practice this shouldn't matter much;
transfers with longer intervals tend to be rather short anyway (things
like hubs or HID devices).

Another minor drawback is that we will keep track of two different
period and phase values: the actual ones and the ones used for
bandwidth allocation (which are limited to 64).  This adds only a
small amount of overhead: 3 bytes for each endpoint.

The patch also adds a new debugfs file named "bandwidth" to display
the information stored in the new table.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch begins the process of unifying the scheduling parameters
that ehci-hcd uses for interrupt and isochronous transfers.  It
creates an ehci_per_sched structure, which will be stored in both
ehci_qh and ehci_iso_stream structures, and will contain the common
scheduling information needed for both.

Initially we merely create the new structure and move some existing
fields into it.  Later patches will add more fields and utilize these
structures in improved scheduling algorithms.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

These aren't necessary after switch and if blocks.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch removes the duplicate of debug_async_open() prototype following
three lines below the debug_async_open() declaration.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The debugging code for ehci is enabled to run if the DEBUG flag is defined.
This patch enables the debugging code also when the kernel is configured
with dynamic debugging on.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1664) converts ehci-hcd's async_unlink, async_iaa, and
intr_unlink from singly-linked lists to standard doubly-linked
list_heads.  Originally it didn't seem necessary to use list_heads,
because items are always added to and removed from these lists in FIFO
order.  But now with more list processing going on, it's easier to use
the standard routines than continue with a roll-your-own approach.

I don't know if the code ends up being notably shorter, but the
patterns will be more familiar to any kernel hacker.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1622) removes the USB-2.1 Link Power Management code
from the ehci-hcd driver.  This code was never integrated with
usbcore, it is full of bugs, and it was not getting used by anybody.

However, the debugging code for dumping the LPM-related fields in the
EHCI registers is left in place.  In theory it might be useful to see
these values, even though we don't use them.

This essentially amounts to a partial revert of commit
aa4d8342 (USB: EHCI: EHCI 1.1
addendum: preparation) and an almost full revert of commit
48f24970 (USB: EHCI: EHCI 1.1
addendum: Basic LPM feature support) plus its follow-ons.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In preparation for splitting the ehci-hcd driver into a core library
and separate platform-specific driver modules, this patch (as1616)
moves the console logging macros from ehci-dbg.c to ehci.h, where they
will be available to the platform drivers.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1605) removes a useless test from the EHCI debugfs
code.  There's no point checking whether p.qh is non-NULL; we already
know it is and in any case it gets dereferenced aerlier in the
function.

The useless test was identified by smatch.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1571) adds a new state for ehci-hcd's root hubs:
EHCI_RH_STOPPING.  This value is used at times when the root hub is
being stopped and we don't know whether or not the hardware has
finished all its DMA yet.

Although the purpose may not be apparent, this distinction will come
in useful later on.  Future patches will avoid actions that depend on
the root hub being operational (like turning on the async or periodic
schedules) when they see the state is EHCI_RH_STOPPING.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1569) renames the ehci->reclaim list in ehci-hcd.  The
word "reclaim" is used in the EHCI specification to mean something
quite different, and "unlink_next" is more descriptive of the list's
purpose anyway.

Similarly, the "reclaim" field in the ehci_stats structure is renamed
"iaa", which is more meaningful (to experts, anyway) and is a better
match for the "lost_iaa" field.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1568) introduces symbolic constants for some of the
less-frequently used bitfields in the QH structure.  This makes the
code a little easier to read and understand.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The ehci-hcd driver is a little haphazard about keeping track of the
state of the USBCMD register.  The ehci->command field is supposed to
hold the register's value (apart from a few special bits) at all
times, but it isn't maintained properly.

This patch (as1543) cleans up the situation.  It keeps ehci->command
up-to-date, and uses that value rather than reading the register from
the hardware whenever possible.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op.  This leads to a
proliferation of the default_open() implementation across the entire
tree.

Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().

This replacement was done with the following semantic patch:

<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}

@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>

[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Correct spelling "peridic" to "periodic" in
drivers/usb/host/ehci-dbg.c
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Correct spelling "peridic" to "periodic" in
drivers/usb/host/ehci-dbg.c
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch (as1489) works around a hardware bug in MosChip EHCI
controllers.  Evidently when one of these controllers increments the
frame-index register, it changes the three low-order bits (the
microframe counter) before changing the higher order bits (the frame
counter).  If the register is read at just the wrong time, the value
obtained is too low by 8.

When the appropriate quirk flag is set, we work around this problem by
reading the frame-index register a second time if the first value's
three low-order bits are all 0.  This gives the hardware a chance to
finish updating the register, yielding the correct value.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NJason N Pitt <jpitt@fhcrc.org>
CC: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1483) improves the ehci-hcd driver family by getting rid
of the reliance on the hcd->state variable.  It has no clear owner and
it isn't protected by the usual HCD locks.  In its place, the patch
adds a new, private ehci->rh_state field to record the state of the
root hub.

Along the way, the patch removes a couple of lines containing
redundant assignments to the state variable.  Also, the QUIESCING
state simply gets changed to the RUNNING state, because the driver
doesn't make any distinction between them.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The two first HC capability registers (CAPLENGTH and HCIVERSION)
are defined as one 8-bit and one 16-bit register. Most HC
implementations have selected to treat these registers as part
of a 32-bit register, giving the same layout for both big and
small endian systems.

This patch adds a new quirk, big_endian_capbase, to support
controllers with big endian register interfaces that treat
HCIVERSION and CAPLENGTH as individual registers.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The vdbg macro is not used anywhere so it can be removed.

With pre-release GCC-4.6, there are several complaints of variables
that are 'set but not used' caused by the ehci_vdbg() macro expanding
to something that does not contain any of its arguments.  We can quiet
this warning by rewriting ehci_vdbg() as a variadic static inline that
does nothing.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Hi,

The [vk][cmz]alloc(_node) family of functions return void pointers which
it's completely unnecessary/pointless to cast to other pointer types since
that happens implicitly.

This patch removes such casts from drivers/usb/
Signed-off-by: NJesper Juhl <jj@chaosbits.net>

The permissions for the lpm debugfs file is incorrect, this fixes it.
Reported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: Alek Du <alek.du@intel.com>
Cc: Jacob Pan <jacob.jun.pan@intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.

The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.

New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time.  Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.

The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.

Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.

Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.

===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
//   but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}

@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}

@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
   *off = E
|
   *off += E
|
   func(..., off, ...)
|
   E = *off
)
...+>
}

@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}

@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
  *off = E
|
  *off += E
|
  func(..., off, ...)
|
  E = *off
)
...+>
}

@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}

@ fops0 @
identifier fops;
@@
struct file_operations fops = {
 ...
};

@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
 .llseek = llseek_f,
...
};

@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
 .read = read_f,
...
};

@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
 .write = write_f,
...
};

@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
 .open = open_f,
...
};

// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
...  .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};

@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
...  .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};

// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
...  .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};

// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};

// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};

@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+	.llseek = default_llseek, /* write accesses f_pos */
};

// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////

@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
 .write = write_f,
 .read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};

@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};

@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};

@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>

The patch below on gregkh tree only creates 'lpm' file under
ehci->debug_dir, but not removes it when unloading module,

	 USB: EHCI: EHCI 1.1 addendum: preparation

which can make loading of ehci-hcd module failed after unloading it.

This patch replaces debugfs_remove with debugfs_remove_recursive
to remove ehci debugfs dir and files. It does fix the bug above,
and may simplify the removing procedure.

Also, remove the debug_registers, debug_async and debug_periodic
field from ehci_hcd struct since they are useless now.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1393) converts several of the single-bit fields in
struct usb_hcd to atomic flags.  This is for safety's sake; not all
CPUs can update bitfield values atomically, and these flags are used
in multiple contexts.

The flag fields that are set only during registration or removal can
remain as they are, since non-atomic accesses at those times will not
cause any problems.

(Strictly speaking, the authorized_default flag should become atomic
as well.  I didn't bother with it because it gets changed only via
sysfs.  It can be done later, if anyone wants.)
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

EHCI 1.1 addendum introduced several energy efficiency extensions for
EHCI USB host controllers:
1. LPM (link power management)
2. Per-port change
3. Shorter periodic frame list
4. Hardware prefetching

This patch is intended to define the HW bits and debug interface for
EHCI 1.1 addendum. The LPM and Per-port change patches will be sent out
after this patch.
Signed-off-by: NJacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: NAlek Du <alek.du@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The ehci_qh structure merged hw and sw together which is not good:
1. More and more items are being added into ehci_qh, the ehci_qh software
   part are unnecessary to be allocated in DMA qh_pool.
2. If HCD has local SRAM, the sw part will consume it too, and it won't
   bring any benefit.
3. For non-cache-coherence system, the entire ehci_qh is uncachable, actually
   we only need the hw part to be uncacheable. Spliting them will let the sw
   part to be cacheable.
Signed-off-by: NAlek Du <alek.du@intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

vfree() does it's own NULL checking,so no need for check before
calling it.
Signed-off-by: NFigo.zhang <figo1802@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

temp, bytes and param->{length,sglen,vary} are unsigned so
these tests do nothing.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1145) removes the essentially useless driver-version
strings from ehci-hcd, ohci-hcd, and uhci-hcd.  It also unifies the
form of the banner lines they display upon loading and adds a missing
test for usb_disabled() to ehci-hcd.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fix 2 problems about reading periodic file:

1. The "..." after a interrupt qh is missed because buffer pointer is
   not moved.

2. After setting p.ptr as NULL, its next qh or itd will be omited and
   can't be stored in debug buffer.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch is based on the following ideas:

1. Some usb devices (such as usb video class) have endpoints of high
   interval attribute, so reading "periodic" file need more debug buffer
   to accommodate the qh or itd schedule information.  For example, 4KB
   buffer is not enough for a single interrupt qh of 2ms period.

2. print a %p need 16 byte buffer on 64-bits arch, but 8 byte on 32-bits
   arch. Add a extra bonus for 64-bits arch.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The bus_id field is going away, use the dev_name() function instead.
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* endianness annotations
* endianness fixes
* missing get_unaligned/put_unaligned

It's pretty much all over the place, changes to different files are independent.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Serial-parts-Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

power.power_state is scheduled for removal.  This patch (as1053)
removes all uses of that field from drivers/usb.  Almost all of them
were write-only, the most significant exceptions being sl811-hcd.c and
u132-hcd.c.

Part of this patch was written by Pavel Machek.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Minor cleanups to the EHCI code:  revision history is what source
code repositories should have.  Switch to a more standard way to
kick in verbose debugging -- don't be EHCI-specific.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1028) was mostly written by David Brownell; I made only
a few changes (extra log info and a small bug fix -- which might
account for why David's version had to be reverted).  It adds a new
watchdog timer to the ehci-hcd driver to be used exclusively for
detecting lost or missing IAA notifications.

Previously a shared timer had been used, which may have led to some
problems as reported by Christian Hoffmann.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>