mainline inclusion
from mainline-master
commit e435a6b5
category: feature
bugzilla: https://gitee.com/openeuler/kernel/issues/I4I7P7
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e435a6b5315a

----------------------------------------------------------------------

Currently, there are two ways for PF to set the unicast MAC address space
size: specified by config parameters in firmware or set to default value.

That's mean if the config parameters in firmware is zero, driver will
divide the whole unicast MAC address space equally to 8 PFs. However, in
this case, the unicast MAC address space will be wasted a lot when the
hardware actually has less then 8 PFs. And in the other hand, if one PF has
much more VFs than other PFs, then each function of this PF will has much
less address space than other PFs.

In order to ameliorate the above two situations, introduce the third way
of unicast MAC address space assignment: firmware divides the whole unicast
MAC address space equally to functions of all PFs, and calculates the space
size of each PF according to its function number. PF queries the space size
by the querying device specification command when in initialization
process.

The third way assignment is lower priority than specified by config
parameters, only if the config parameters is zero can be used, and if
firmware does not support the third way assignment, then driver still
divides the whole unicast MAC address space equally to 8 PFs.
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.76
commit d36b15e3e7b5937cb1f6ac590a85facc3a320642
bugzilla: 182988 https://gitee.com/openeuler/kernel/issues/I4IAHF

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=d36b15e3e7b5937cb1f6ac590a85facc3a320642

--------------------------------

[ Upstream commit 0dd8a25f ]

HNS3 driver includes hns3.ko, hnae3.ko and hclge.ko.
hns3.ko includes network stack and pci_driver, hclge.ko includes
HW device action, algo_ops and timer task, hnae3.ko includes some
register function.

When SRIOV is enable and hclge.ko is removed, HW device is unloaded
but VF still exists, PF will not reply VF mbx messages, and cause
errors.

This patch fix it by disable SRIOV before remove hclge.ko.

Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: NWeilong Chen <chenweilong@huawei.com>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.71
commit d4a14faf7919b331d95d87d7d84e36774f9408c4
bugzilla: 182981 https://gitee.com/openeuler/kernel/issues/I4I3KD

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=d4a14faf7919b331d95d87d7d84e36774f9408c4

--------------------------------

[ Upstream commit 108b3c78 ]

Currently, if function adds an existing unicast mac address, eventhough
driver will not add this address into hardware, but it will return 0 in
function hclge_add_uc_addr_common(). It will cause the state of this
unicast mac address is ACTIVE in driver, but it should be in TO-ADD state.

To fix this problem, function hclge_add_uc_addr_common() returns -EEXIST
if mac address is existing, and delete two error log to avoid printing
them all the time after this modification.

Fixes: 72110b56 ("net: hns3: return 0 and print warning when hit duplicate MAC")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: NWeilong Chen <chenweilong@huawei.com>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-v5.15-rc3
commit 5126b9d3
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I4CVS3
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=5126b9d3d4ac

----------------------------------------------------------------------

hclge_get_reset_status() should return the tqp reset status.
However, if the CMDQ fails, the caller will take it as tqp reset
success status by mistake. Therefore, uses a parameters to get
the tqp reset status instead.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-v5.15-rc3
commit ef39d632
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I4CVS3
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=ef39d632608e

----------------------------------------------------------------------

The input parameters may not be reliable, so check the vlan id before
using it, otherwise may set wrong vlan id into hardware.

Fixes: dc8131d8 ("net: hns3: Fix for packet loss due wrong filter config in VLAN tbls")
Signed-off-by: Nliaoguojia <liaoguojia@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-v5.15-rc3
commit 311c0aaa
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I4CVS3
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=311c0aaa9b4b

----------------------------------------------------------------------

vport_id include PF and VFs, vport_id = 0 means PF, other values mean VFs.
So the actual vf id is equal to vport_id minus 1.

Some VF print logs are actually vport, and logs of vf id actually use
vport id, so this patch fixes them.

Fixes: ac887be5 ("net: hns3: change print level of RAS error log from warning to error")
Fixes: adcf738b ("net: hns3: cleanup some print format warning")
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-v5.15-rc3
commit 91bc0d52
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I4CVS3
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=91bc0d5272d3

----------------------------------------------------------------------

The vf id from ethtool is added 1 before configured to driver.
So it's necessary to minus 1 when printing it, in order to
keep consistent with user's configuration.

Fixes: dd74f815 ("net: hns3: Add support for rule add/delete for flow director")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-v5.15-rc3
commit e184cec5
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I4CVS3
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e184cec5e29d

----------------------------------------------------------------------

When user change rss 'hfunc' without set rss 'hkey' by ethtool
-X command, the driver will ignore the 'hfunc' for the hkey is
NULL. It's unreasonable. So fix it.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: 374ad291 ("net: hns3: Add RSS general configuration support for VF")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-v5.15-rc2
commit b81d8948
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I4CVS3
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=b81d89487465

----------------------------------------------------------------------

The firmware will not disable mac in flr process. Therefore, the driver
needs to proactively disable mac during flr, which is the same as the
function reset.

Fixes: 35d93a30 ("net: hns3: adjust the process of PF reset")
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-v5.15-rc2
commit 1dc839ec
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I4CVS3
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=1dc839ec09d3

----------------------------------------------------------------------

Currently, affinity_mask is set to a single cpu. As a result,
irqbalance becomes invalid in SUBSET or EXACT mode. To solve
this problem, change affinity_mask to numa node range. In this
way, irqbalance can be performed on the cpu of the numa node.

Fixes: 08125454 ("net: hns3: add interrupt affinity support for misc interrupt")
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-v5.15-rc1
commit 7f2d4b7f
category: feature
bugzilla: https://gitee.com/openeuler/kernel/issues/I4BY3P
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7f2d4b7ffa42565a41f0fd6aa147d84863bb088b

----------------------------------------------------------------------

This patch removes some unnecessary spaces for cleanup.
Signed-off-by: NHao Chen <chenhao288@hisilicon.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-v5.15-rc1
commit c74e5035
category: feature
bugzilla: https://gitee.com/openeuler/kernel/issues/I4BY3P
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=c74e503572ea0dbfa6ef3449944a286354f9f9b4

----------------------------------------------------------------------

Add some required spaces to improve readability.
Signed-off-by: NHao Chen <chenhao288@hisilicon.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-v5.15-rc1
commit 0cb07041
category: feature
bugzilla: https://gitee.com/openeuler/kernel/issues/I4BY3P
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=0cb0704149f0d9d3b7c68ebab932fc27222c740b

----------------------------------------------------------------------

Add some required spaces in comment for cleanup.
Signed-off-by: NHao Chen <chenhao288@hisilicon.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-v5.15-rc1
commit aec35aec
category: feature
bugzilla: https://gitee.com/openeuler/kernel/issues/I4BY3P
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=aec35aecc3ccc822b358e2594ff70ff54245261e

----------------------------------------------------------------------

Currently, function hclge_check_port_speed() uses switch/case statement
to get speed bit according to speed. To reuse this part of code and
improve code readability and maintainability, add a new function
hclge_get_speed_bit() to get speed bit according to map relationship
of speed and speed bit defined in array speed_bit_map.
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-v5.15-rc1
commit 5a24b1fd
category: feature
bugzilla: https://gitee.com/openeuler/kernel/issues/I4BY3P
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=5a24b1fd301e0cf0fc58a76f2716c54d378002cf

----------------------------------------------------------------------

There are some repetitive macros have same meaning and value, this patch
merges them to make code clean.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-v5.15-rc1
commit 4c116f85
category: feature
bugzilla: https://gitee.com/openeuler/kernel/issues/I4BY3P
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=4c116f85ecf8c147450602ed47ee25de60807f45

----------------------------------------------------------------------

To improve code readability, replace digital numbers of mac speeds
defined by firmware command with macros.
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit 9f0c6f4b
category: feature
bugzilla: https://gitee.com/openeuler/kernel/issues/I46N7D
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=9f0c6f4b7475dd97e1f0eed81dd6ff173cf8c7fc

----------------------------------------------------------------------

For device whose version is above V3(include V3), the GL can
select EQE or CQE mode, so adds support for it.

In CQE mode, the coalesced timer will restart when the first new
completion occurs, while in EQE mode, the timer will not restart.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-v5.14
commit 3462207d
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I46N6O
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=3462207d2d684658d97499ca77c00c9ac7c87ea8

----------------------------------------------------------------------

The GRO configuration is enabled by default after reset. This
is incorrect and should be restored to the user-configured value.
So this restoration is added during reset initialization.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-v5.14
commit 94391fae
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I46N6O
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=94391fae82f71c98ecc7716a32611fcca73c74eb

----------------------------------------------------------------------

VLAN list should not be added duplicate VLAN node, otherwise it would
cause "add failed" when restore VLAN from VLAN list, so this patch adds
VLAN ID check before adding node into VLAN list.

Fixes: c6075b19 ("net: hns3: Record VF vlan tables")
Signed-off-by: NGuojia Liao <liaoguojia@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-v5.14
commit b15c072a
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I46N6O
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=b15c072a9f4a404c09ad589477f4389034742a8b

----------------------------------------------------------------------

In bond 4, when the link goes down and up repeatedly, the bond may get an
unknown speed, and then this port can not work.

The driver notify netif_carrier_on() before update the link state, when the
bond receive carrier on, will query the speed of the port, if the query
operation happens before updating the link state, will get an unknown
speed. So need to notify netif_carrier_on() after update the link state.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-v5.14
commit 1a6d2819
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I46N6O
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=1a6d281946c330cee2855f6d0cd796616e54601f

----------------------------------------------------------------------

If a PF is bonded to a virtual machine and the virtual machine exits
unexpectedly, some hardware resource cannot be cleared. In this case,
loading driver may cause exceptions. Therefore, the hardware resource
needs to be cleared when the driver is loaded.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit f5c2b9f0
category: feature
bugzilla: https://gitee.com/openeuler/kernel/issues/I46N7D
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=f5c2b9f0fc078308a88de807d60cd4e352a165fc

----------------------------------------------------------------------

In order to know the reason of link up failure, add supporting ethtool
extended link state. Driver reads the link status code from firmware if
in link down state and converts it to ethtool extended link state.
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit ddccc5e3
category: feature
bugzilla: https://gitee.com/openeuler/kernel/issues/I46N7D
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=ddccc5e368a33daeb6862192d4dca8e59af9234a

----------------------------------------------------------------------

Currently, four reset types are supported for the HNS3 ethernet
driver: IMP reset, global reset, function reset, and FLR. Only
FLR can now be triggered by the user. To restore the device when
an exception occurs, add support for triggering reset by ethtool.

Run the "ethtool --reset DEVNAME mgmt | all | dedicated" to
trigger the IMP | global | function reset manually.

In addition, VF can only trigger function reset.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Link: https://lore.kernel.org/r/1628602128-15640-1-git-send-email-huangguangbin2@huawei.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit b741269b
category: feature
bugzilla: 173966
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=b741269b275953786832805df329851299ab4de7

----------------------------------------------------------------------

Add devlink register support for HNS3 ethernet PF driver.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit 184cd221
category: feature
bugzilla: 173966
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=184cd221a86321e53df9389c4b35a247b60c1e77

----------------------------------------------------------------------

For hardware limitation, port VLAN filter is port level, and
effective for all the functions of the port. So if not support
port VLAN bypass, it's necessary to disable the port VLAN filter,
in order to support function level VLAN filter control.

Fixes: 2ba30662 ("net: hns3: add support for modify VLAN filter state")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit 03a92fe8
category: feature
bugzilla: 173966
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=03a92fe8cedb6f619df416d38d0b57fd55070cd7

----------------------------------------------------------------------

Previously, the flow director counter is not enabled. To improve the
maintainability for chechking whether flow director hit or not, enable
flow director counter for each function, and add debugfs query inerface
to query the counters for each function.

The debugfs command is below:
cat fd_counter
func_id    hit_times
pf         0
vf0        0
vf1        0
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit 1a00197b
category: feature
bugzilla: 173966
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=1a00197b7d2fe57f0be93037d5090e19a9b178c8

----------------------------------------------------------------------

Add support to query tx spare buffer size from configuration
file, and use this info to do spare buffer initialization when
the module parameter 'tx_spare_buf_size' is not specified.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit 0bf5eb78
category: feature
bugzilla: 173966
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=0bf5eb788512187b744ef7f79de835e6cbe85b9c

----------------------------------------------------------------------

Adds PTP support for HNS3 ethernet driver.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit 4724acc4
category: feature
bugzilla: 173966
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=4724acc47c9441ec1e131299853d1a9e8c3fb2cd

----------------------------------------------------------------------

Using list_move_tail() instead of list_del() + list_add_tail() in hclge_main.c.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NBaokun Li <libaokun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit 1c360a4a
category: feature
bugzilla: 173966
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=1c360a4a077fc0f74a350fe2ef267cbe8a9388e3

----------------------------------------------------------------------

During initialization, the driver logs and clears the hw errors that
already occurred. For device supports imp-handle ras capability, it
needs handle different error status, otherwise it may cause wrong reset.

So fix it by adding a new processing branch.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit 8a95e360
category: feature
bugzilla: 173966
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=8a95e360fd512f1cb55239645879b15d26bc7e21

----------------------------------------------------------------------

Update error recovery module and type for RoCE.

The enumeration values of module names and error types are not sorted
in sequence. If use the current printing mode, they cannot be correctly
printed.

Use the index mode, If mod_id and type_id match the enumerated value,
display the corresponding information.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: NWeihang Li <liweihang@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit e65e9f5c
category: feature
bugzilla: 173966
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e65e9f5c2e4efc17657d016d767eb7010d9dd598

----------------------------------------------------------------------

IMP(Intelligent Management Processor) firmware add a new feature to
handle and consolidate RAS information for new devices, NIC driver
only needs to query the reported RAS information. NIC driver adds
support for this feature.

Driver queries device capability to check whether IMP support this
feature, If yes, execute the new RAS processing branch.

In order to add a method to check whether PF supports imp-handle RAS
feature, add dumping this info in debugfs.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit 2e2deee7
category: feature
bugzilla: 173966
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=2e2deee7618b062efe3aba9fcb017dadcf148819

----------------------------------------------------------------------

To adapt to hardware modification and ensure that the driver is
compatible with the original error handling content, we need to add the
RAS compatibility adaptation solution.

Add a processing branch to the driver during error handling. In the new
processing branch, NIC fault information is integrated by the IMP. An
interaction command is added between the driver and IMP to query
and clear the fault source and interrupt source. The IMP integrates
error information and reports the highest reset level to the driver.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit 17f59244
category: feature
bugzilla: 173966
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=17f59244029bf9c0673725efdd0386ed95e127a7

----------------------------------------------------------------------

Currently, hardware errors can be reported through AER or MSI-X mode.
However, the AER mode is intended to handle only bus errors, but not
hardware errors. On the other hand, virtual machines cannot handle
AER errors. When an AER error is reported, virtual machines will be
suspended. So add support for handling all these hardware errors
through MSI-X mode which depends on a newer version of firmware,
and reserve the handler of the AER mode for compatibility.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit e0fe0a38
category: feature
bugzilla: 173966
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e0fe0a38371b6d2d669e231c1fd68ce620dfa6b2

----------------------------------------------------------------------

Earlier patches have decoupled the MSI-X conveyed error handling
and recovery logic. This earlier concept code is no longer required.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit aff399a6
category: feature
bugzilla: 173966
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=aff399a638da7e56680cdf6fa7544b67e0373a4e

----------------------------------------------------------------------

Error handling & recovery is done in context of reset task which
gets scheduled from misc interrupt handler in existing code. But
since error handling has been moved to new task, it should get
scheduled instead of the reset task from the interrupt handler.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit d991452d
category: feature
bugzilla: 173966
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=d991452dd7900cf152ffb43db3b1d385e1a01579

----------------------------------------------------------------------

Error handling and recovery logic are intertwined. Error handling (i.e.
error identification, clearing error sources and initiation of recovery)
is done in context of reset task. If certain hardware errors get
delivered during driver init time, which can cause driver init/loading
to fail.

Introduce a separate error handling task to ensure below:

1. Reset logic remains independent of the error handling logic.
2. Add the hclge_errhand_task_schedule to schedule error recovery
tasks, This will ensure that common misellaneous MSI-X interrupt are
re-enabled quickly.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit 0ca821da
category: feature
bugzilla: 173966
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=0ca821da86a5ec24eb2ece24fe87e5bf518c5939

----------------------------------------------------------------------

Add debugfs support for vlan configuraion. create a single file
"vlan_config" for it, and query it by command "cat vlan_config",
return the result to userspace.

The new display style is below:
$ cat vlan_config
I_PORT_VLAN_FILTER: on
E_PORT_VLAN_FILTER: off
FUNC_ID  I_VF_VLAN_FILTER  E_VF_VLAN_FILTER  PORT_VLAN_FILTER_BYPASS
pf       off               on                off
vf0      off               on                off
FUNC_ID  PVID    ACCEPT_TAG1  ACCEPT_TAG2  ACCEPT_UNTAG1  ACCEPT_UNTAG2
pf       0       on           on           on             on
vf0      0       on           on           on             on
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit fa6a262a
category: feature
bugzilla: 173966
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=fa6a262a255003ebb1f514fffd3399f3946d4fc9

----------------------------------------------------------------------

Previously, there is hardware limitation for VF to modify
the VLAN filter state, and the VLAN filter state is default
enabled. Now the limitation has been removed in some device,
so add capability flag to check whether the device supports
modify VLAN filter state. If flag on, user will be able to
modify the VLAN filter state by ethtool -K.
VF needs to send mailbox to request the PF to modify the VLAN
filter state for it.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

mainline inclusion
from mainline-master
commit 2ba30662
category: feature
bugzilla: 173966
CVE: NA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=2ba306627f5950c9a7850f3b0499d39e522dc249

----------------------------------------------------------------------

Previously, with hardware limitation, the port VLAN filter are
effective for both PF and its VFs simultaneously, so a single
function is not able to enable/disable separately, and the VLAN
filter state is default enabled. Now some device supports each
function to bypass port VLAN filter, then each function can
switch VLAN filter separately. Add capability flag to check
whether the device supports modify VLAN filter state. If flag
on, user will be able to modify the VLAN filter state by ethtool
-K.

Furtherly, the default VLAN filter state is also changed
according to whether non-zero VLAN used. Then the device can
receive packet with any VLAN tag if only VLAN 0 used.

The function hclge_need_enable_vport_vlan_filter() is used to
help implement above changes. And the VLAN filter handle for
promisc mode can also be simplified by this function.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NYongxin Li <liyongxin1@huawei.com>
Signed-off-by: NJunxin Chen <chenjunxin1@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>