There is no point in displaying the TS5500-specific driver entries if
TS5500 board support itself isn't enabled.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Instead of writing to "nand->reg + REG_FMICSR" we write to "REG_FMICSR"
which is NULL and not a valid register.

Fixes: 8bff82cb ('mtd: add nand support for w90p910 (v2)')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Check the chip->jedec_version, and print out the right information
for JEDEC compliant NAND.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

This patch adds the parsing code for the JEDEC compliant NAND.

Since we need the 0x40 as the column address, this patch also
makes the NAND_CMD_PARAM to use the 8-bit address only.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Check the return value from platform_get_irq() and propagate it in the case of
error.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

"rc" is an error code here, no need to check it a second time.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

PIO fall back is not an issue, so don't make this much noise.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Signed-off-by: NYusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The ELM driver incorrectly reagard any non-zero return value from
pm_runtime_get_sync as an error, but it may return 1 if the device
was already active. Fix to only error when return value is negative.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

read_buf is called in place of write_buf in the
nand_write_page_raw_syndrome function.
Signed-off-by: NBoris BREZILLON <b.brezillon.dev@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM and HAS_DMA to bypass build failures.

drivers/built-in.o: In function `flctl_probe':
drivers/mtd/nand/sh_flctl.c:1097: undefined reference to `devm_ioremap_resource'
drivers/built-in.o: In function `flctl_dma_fifo0_transfer':
drivers/mtd/nand/sh_flctl.c:368: undefined reference to `dma_map_single'
drivers/mtd/nand/sh_flctl.c:407: undefined reference to `dma_unmap_single'
Signed-off-by: NRichard Weinberger <richard@nod.at>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

For slightly better readability.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Use a repeated read_byte() instead of read_buf(), since for x16 buswidth
devices, we need to avoid the upper I/O[16:9] bits. See the following
commit for reference:

commit 05f78359
Author: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Date:   Thu Dec 5 22:22:04 2013 +0100

    mtd: nand: don't use {read,write}_buf for 8-bit transfers

Now, I think that all barriers to probing ONFI on x16 devices are
removed, so remove the check from nand_flash_detect_onfi().

Tested on 8-bit ONFI NAND (Micron MT29F32G08CBADAWP).
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Tested-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-By: NPekon Gupta <pekon@ti.com>

The NAND command helpers tend to automatically shift the column address
for x16 bus devices, since most commands expect a word address, not a
byte address. The Read ID command, however, expects an 8-bit address
(i.e., 0x00, 0x20, or 0x40 should not be translated to 0x00, 0x10, or
0x20).

This fixes the column address for a few drivers which imitate the
nand_base defaults. Note that I don't touch sh_flctl.c, since it already
handles this problem slightly differently (note its comment "READID is
always performed using an 8-bit bus").

I have not tested this patch, as I only have x8 parts up for testing at
this point. Hopefully that can change soon...
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Tested-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-By: NPekon Gupta <pekon@ti.com>

The datasheet does not tell us how to parse out the ID data,
so handle it as a full ID nand.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The patch converts the arrays to buffer pointers for nand_buffers{}.

The cafe_nand.c is the only NAND_OWN_BUFFERS user which allocates
nand_buffers{} itself.

This patch disables the DMA for nand_scan_ident, and restores the DMA
status after we finish the nand_scan_ident. This way, we can get page
size and OOB size and use them to allocate cafe->dmabuf.

Since the cafe_nand.c uses the NAND_ECC_HW_SYNDROME ECC mode, we do not
allocate the buffers for @ecccalc and @ecccode.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.  Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.

Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
[Brian: dropped one incorrect hunk]
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

mutex_destroy added on each device in block2mtd_exit and add_device failure
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Commit b2a2a84d (mtd: phram: dot not crash when
built-in and passing boot param) claims to be "based on Ville Herva's similar
patch to block2mtd" (c4e7fb31), but it has
missed the crucial point of the original path: all these "if(n)def MODULE".
It has broken the possibility to create several phram instances when phram is
compiled as module. The possibility to add instances via /sys writes to
/sys/module/phram/parameters/phram was also broken with mentioned patch.
Proposed patch takes the idea of original block2mtd patch to its full extent.
Assumption "This function is always called before 'init_phram()'" was also
incorrect, so removed the comment. This patch effectively reverts also
b11ec57f (mtd: phram: fix section mismatch for
phram_setup).
Signed-off-by: NAlexander Sverdlin <alexander.sverdlin@nsn.com>
[Brian: remove static assigment = 0]
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

We always put a NUL terminator one space past the end of the "vendor"
buffer.  Walter Harms also pointed out that this should just use
kstrndup().

Fixes: 7d17c02a ('mtd: Add new SmartMedia/xD FTL')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Spansion s25fl256s1 and s25fl512s support Dual SPI transfers, hence set the
M25P80_DUAL_READ flag.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Add support for Dual SPI read transfers, which is supported by some
Spansion SPI FLASHes.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

This patch excludes reserved-marker byte-position from oobfree->length
calculation. Thus all bytes from oobfree->offset till end of OOB are free.

CC: <stable@vger.kernel.org> # 3.13.x+
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

1) In current implementation, ecclayout->oobfree->offset is calculated with
 respect to ecclayout->eccpos[0] which is incorrect because ECC bytes may not
 be stored contiguously in OOB.
 So, this patch calculates ecclayout->oobfree->offset with respect to last
 ECC byte-position 'eccpos[ecclayout->eccbytes-1]'.

2) ECC layout of some ecc-schemes expects reserved-markers at specific eccpos[]
 which should not be over-written by any file-system metadata.
 So this patch aligns oobfree->offset taking into account of such markers.

CC: <stable@vger.kernel.org> # 3.13.x+
Tested-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: NStefan Roese <sr@denx.de>
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Fixes: commit a919e511
       mtd: nand: omap2: clean-up BCHx_HW and BCHx_SW ECC configurations in device_probe

Fixes ecclayout mismatch introduced in above commit for following ecc-schemes:
 - OMAP_ECC_BCH4_CODE_HW_DETECTION_SW
 - OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
 However, this patch also touches other ecc-schemes as the fix required
 refactoring common code, into ecc-scheme specific code.

This patch aligns ecc-layout for below ecc-schemes as per reference [1],[2],[3]

 +---+------------+-------------++-------------+-------------+
 |OOB|BCH8_CODE_HW|BCH8_CODE_HW_||HAM1_CODE_HW |HAM1_CODE_HW |
 |pos|            | DETECTION_SW||(x8 device)  |(x16 device) |
 +---+------------+-------------++-------------+-------------+
 | 0 |BADBLK_MARK | BADBLK_MARK || BADBLK_MARK | BADBLK_MARK |
 | 1 |BADBLK_MARK | BADBLK_MARK || eccpos[0]   | BADBLK_MARK |
 | 2 | eccpos[0]  | eccpos[0]   || eccpos[1]   | eccpos[0]   |
 | 3 | eccpos[1]  | eccpos[1]   || eccpos[2]   | eccpos[1]   |
 | 4 | eccpos[2]  | eccpos[2]   || eccpos[3]   | eccpos[2]   |
 | 5 | eccpos[3]  | eccpos[3]   || eccpos[4]   | eccpos[3]   |
 | 6 | eccpos[4]  | eccpos[4]   || eccpos[5]   | eccpos[4]   |
 | 7 | eccpos[5]  | eccpos[5]   || eccpos[6]   | eccpos[5]   |
 | 8 | eccpos[6]  | eccpos[6]   || eccpos[7]   | eccpos[6]   |
 | 9 | eccpos[7]  | eccpos[7]   || eccpos[8]   | eccpos[7]   |
 |10 | eccpos[8]  | eccpos[8]   || eccpos[9]   | eccpos[8]   |
 |11 | eccpos[9]  | eccpos[9]   || eccpos[10]  | eccpos[9]   |
 |12 | eccpos[10] | eccpos[10]  || eccpos[11]  | eccpos[10]  |
 |13 | eccpos[11] | eccpos[11]  || oobfree[0]  | eccpos[11]  |
 |14 | eccpos[12] | eccpos[12]  || oobfree[1]  | oobfree[0]  |
 |15 | eccpos[13] | <reserved>  || oobfree[2]  | oobfree[1]  |
 +---+------------+-------------++-------------+-------------+
 |16 | eccpos[14] | eccpos[13]  || oobfree[3]  | oobfree[2]  |
 |...| [...]      | [...]       || [...]       | [...]       |
 |56 | eccpos[54] | eccpos[51]  || oobfree[43] | oobfree[42] |
 |57 | eccpos[55] | <reserved>  || oobfree[44] | oobfree[43] |
 +===+============+=============+==============+=============+
 |58 | oobfree[0] | oobfree[0]  || oobfree[45] | oobfree[44] |
 |59 | oobfree[1] | oobfree[1]  || oobfree[46] | oobfree[45] |
 |60 | oobfree[2] | oobfree[2]  || oobfree[47] | oobfree[46] |
 |61 | oobfree[3] | oobfree[3]  || oobfree[48] | oobfree[47] |
 |62 | oobfree[4] | oobfree[4]  || oobfree[49] | oobfree[48] |
 |63 | oobfree[5] | oobfree[5]  || oobfree[50] | oobfree[49] |
 +---+------------+-------------+--------------+-------------+

[1] ecc-layout expected by ROM code, as specified in SoC TRM under:
      Chapter="Initialization"
        Section="Device Initialization by ROM code"
            Sub-Section="Memory Booting"
                Heading="NAND"
                Figure="ECC Locations in NAND Spare Areas"

[2] ecc-layout updates in u-boot
    http://lists.denx.de/pipermail/u-boot/2013-November/167551.html

[3] u-boot configurations to match above ecc-layout are documented at
    https://processors.wiki.ti.com/index.php/Linux_Core_NAND_User%27s_Guide

CC: <stable@vger.kernel.org> # 3.13.x+
Reported-by: NEnric Balletbo Serra <eballetbo@iseebcn.com>
Tested-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: NStefan Roese <sr@denx.de>
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

A flash may support N read retry voltage threshold modes, numbered 0
through N-1 (where mode 0 represents the initial state). However,
nand_do_read_ops() tries to use mode 0 through N.

This off-by-one error shows up, for instance, when using nanddump, and
we have cycled through available modes:

    nand: setting READ RETRY mode 0
    nand: setting READ RETRY mode 1
    nand: setting READ RETRY mode 2
    nand: setting READ RETRY mode 3
    nand: setting READ RETRY mode 4
    nand: setting READ RETRY mode 5
    nand: setting READ RETRY mode 6
    nand: setting READ RETRY mode 7
    nand: setting READ RETRY mode 8
    libmtd: error!: cannot read 8192 bytes from mtd0 (eraseblock 20, offset 0)
            error 22 (Invalid argument)
    nanddump: error!: mtd_read

Tested on Micron MT29F64G08CBCBBH1, with 8 retry modes.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Acked-by: NHuang Shijie <b32955@freescale.com>

Move the kmem_cache_free() calls down a couple lines.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

The buffer pointer passed from the upper layer may points to
a buffer in the stack or a buffer allocated by vmalloc, and etc..

This patch adds more sanity check to this buffer.
After this patch, if we meet a buffer which is allocated by vmalloc or
a buffer in the stack, we will use our own DMA buffer @data_buffer_dma
to do the DMA operations. If the buffer is not the cases above, we will
map it for DMA operations directly.
Signed-off-by: NHuang Shijie <shijie8@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The @data_buffer_dma buffer is used for non ECC read/write.

Currently, the length of the buffer is PAGE_SIZE, but the NAND chip may
has 8K page or 16K page. So we have to extend it for the large page NAND
chips.

The gpmi_alloc_dma_buffer will be called twice. The first time is to
allocate a temporary buffer for scanning the NAND chip; The second time
is to allocate a buffer to store the real page content.

This patch allocates a buffer of PAGE_SIZE size for scanning the NAND
chip when gpmi_alloc_dma_buffer is called the first time, and allocates a
buffer of the real NAND page size for the second time gpmi_alloc_dma_buffer
is called.
Signed-off-by: NHuang Shijie <shijie8@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

When using the Quad Read opcode, SPI masters still use Single SPI
transfers, as spi_transfer.rx_nbits defaults to SPI_NBITS_SINGLE.
Use SPI_NBITS_QUAD to fix this.

While an earlier version of commit 3487a639
("drivers: mtd: m25p80: add quad read support") did this correctly, it was
forgotten in the version that got merged.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Spansion s25fl512s supports Quad SPI transfers, hence set the
M25P80_QUAD_READ flag.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The kernel already has this information, and individual drivers
shouldn't duplicate that.  This also eliminates the use of __DATE__ and
__TIME__, which make the build non-deterministic.
Signed-off-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NMichal Marek <mmarek@suse.cz>