Catalin reported that GPIOs used by bcm47xx don't match layout of his
WRT54GS V1.0 board. It seems we need to distinguish these 54G* devices.
Reported-by: NCatalin Patulea <cat@vv.carleton.ca>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/7112/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch adds detection for the Microsoft MN-700 and the Asus WL500G
router. This is based on some old code from OpenWrt.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: zajec5@gmail.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7490/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add a few Belkin F7Dxxxx entries, with F7D4401 sourced from online
documentation and the "F7D7302" being observed. F7D3301, F7D3302, and
F7D4302 are reasonable guesses which are unlikely to cause
mis-detection.
Signed-off-by: NCody P Schafer <devel@codyps.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Cc: Cody P Schafer <devel@codyps.com>
Patchwork: https://patchwork.linux-mips.org/patch/6594/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This adds board detection for the Siemens SE505v2 and the led gpio
configuration. This board does not have any buttons.
This is based on OpenWrt broadcom-diag and Manuel Munz's nvram dump.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6593/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This adds led and button GPIO configuration for Linksys wrt54g3gv2,
wrt54gsv1 and wrtsl54gs. This is based on OpenWrt broadcom-diag code.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6592/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6313/

Some devices have power LED as well as status LED. The second one is
used to show the firmware is up and running. Set "timer" trigger for
such LEDs.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6312/

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6298/

So far this is mostly just a proof of concept, database consists of a
single device. Creating a nice iterateable array wasn't an option
because devices have different amount of LEDs. And we don't want to
waste memory just because of support for a device with dozens on LEDs.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6299/