MDIO_BUS_MUX can only be selected if OF_MDIO is already turned on:

WARNING: unmet direct dependencies detected for MDIO_BUS_MUX
  Depends on [n]: NETDEVICES [=y] && MDIO_BUS [=m] && OF_MDIO [=n]
  Selected by [m]:
  - MDIO_BUS_MUX_MULTIPLEXER [=m] && NETDEVICES [=y] && MDIO_BUS [=m] && OF [=y]

Fixes: 7865ad65 ("drivers: net: phy: mdio-mux: Add support for Generic Mux controls")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As can be seen from the usage of the return value, we should use
phy_modify_mmd_changed() here.

Fixes: 9a5dc8af ("net: phy: add genphy_c45_an_config_aneg")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the original patch I missed to add mv88e6xxx_ports_cmode_init()
to the second probe function, the one for the new DSA framework.

Fixes: ed8fe202 ("net: dsa: mv88e6xxx: prevent interrupt storm caused by mv88e6390x_port_set_cmode")
Reported-by: NShaokun Zhang <zhangshaokun@hisilicon.com>
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some sky2 chips fire IRQ after S3, before the driver is fully resumed:
[ 686.804877] do_IRQ: 1.37 No irq handler for vector

This is likely a platform bug that device isn't fully quiesced during
S3. Use MSI-X, maskable MSI or INTx can prevent this issue from
happening.

Since MSI-X and maskable MSI are not supported by this device, fallback
to use INTx on affected platforms.

BugLink: https://bugs.launchpad.net/bugs/1807259
BugLink: https://bugs.launchpad.net/bugs/1809843Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Once channels were successfully opened, update tx reporter health state to
healthy. This is needed for the following scenario:
- SQ has an un-recovered error reported to the devlink health, resulting tx
  reporter state to be error.
- Current channels (including this SQ) are closed
- New channels are opened
After that flow, the original error was "solved", and tx reporter state
should be healthy. However, as it was resolved as a side effect, and not
via tx reporter recover method, driver needs to inform devlink health
about it.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When team is used in loadbalance mode a BPF filter can be used to
provide a hash which will determine the Tx port.

When the netdev is later unregistered the filter is not freed which
results in memory leaks [1].

Fix by freeing the program and the corresponding filter when
unregistering the netdev.

[1]
unreferenced object 0xffff8881dbc47cc8 (size 16):
  comm "teamd", pid 3068, jiffies 4294997779 (age 438.247s)
  hex dump (first 16 bytes):
    a3 00 6b 6b 6b 6b 6b 6b 88 a5 82 e1 81 88 ff ff  ..kkkkkk........
  backtrace:
    [<000000008a3b47e3>] team_nl_cmd_options_set+0x88f/0x11b0
    [<00000000c4f4f27e>] genl_family_rcv_msg+0x78f/0x1080
    [<00000000610ef838>] genl_rcv_msg+0xca/0x170
    [<00000000a281df93>] netlink_rcv_skb+0x132/0x380
    [<000000004d9448a2>] genl_rcv+0x29/0x40
    [<000000000321b2f4>] netlink_unicast+0x4c0/0x690
    [<000000008c25dffb>] netlink_sendmsg+0x929/0xe10
    [<00000000068298c5>] sock_sendmsg+0xc8/0x110
    [<0000000082a61ff0>] ___sys_sendmsg+0x77a/0x8f0
    [<00000000663ae29d>] __sys_sendmsg+0xf7/0x250
    [<0000000027c5f11a>] do_syscall_64+0x14d/0x610
    [<000000006cfbc8d3>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
    [<00000000e23197e2>] 0xffffffffffffffff
unreferenced object 0xffff8881e182a588 (size 2048):
  comm "teamd", pid 3068, jiffies 4294997780 (age 438.247s)
  hex dump (first 32 bytes):
    20 00 00 00 02 00 00 00 30 00 00 00 28 f0 ff ff   .......0...(...
    07 00 00 00 00 00 00 00 28 00 00 00 00 00 00 00  ........(.......
  backtrace:
    [<000000002daf01fb>] lb_bpf_func_set+0x45c/0x6d0
    [<000000008a3b47e3>] team_nl_cmd_options_set+0x88f/0x11b0
    [<00000000c4f4f27e>] genl_family_rcv_msg+0x78f/0x1080
    [<00000000610ef838>] genl_rcv_msg+0xca/0x170
    [<00000000a281df93>] netlink_rcv_skb+0x132/0x380
    [<000000004d9448a2>] genl_rcv+0x29/0x40
    [<000000000321b2f4>] netlink_unicast+0x4c0/0x690
    [<000000008c25dffb>] netlink_sendmsg+0x929/0xe10
    [<00000000068298c5>] sock_sendmsg+0xc8/0x110
    [<0000000082a61ff0>] ___sys_sendmsg+0x77a/0x8f0
    [<00000000663ae29d>] __sys_sendmsg+0xf7/0x250
    [<0000000027c5f11a>] do_syscall_64+0x14d/0x610
    [<000000006cfbc8d3>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
    [<00000000e23197e2>] 0xffffffffffffffff

Fixes: 01d7f30a ("team: add loadbalance mode")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If an external PHY is connected via SGMII and uses in-band signalling
then the auto-negotiated values aren't propagated to the port,
resulting in a broken link. See discussion in [0]. This patch adds
this propagation. We need to call mv88e6xxx_port_setup_mac(),
therefore export it from chip.c.

Successfully tested on a ZII DTU with 88E6390 switch and an
Aquantia AQCS109 PHY connected via SGMII to port 9.

[0] https://marc.info/?t=155130287200001&r=1&w=2Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of these macros were conflicting with global namespace,
hence prefixing them with CXGB4.
Signed-off-by: NArjun Vynipadath <arjun@chelsio.com>
Signed-off-by: NVishal Kulkarni <vishal@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend initialization flow by query requests for chip resources data in
order to obtain chip's specific capabilities, like the number of ports.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend input parameters list of command API in mlxsw_i2c_cmd() in order
to support initialization commands. Up until now, only access commands
were supported by I2C driver.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change input parameter name "resource" to "res" in mlxsw_i2c_init() in
order to align it with mlxsw_pci_init().
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix comment for mlxsw_i2c_write_cmd().
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move mlxsw_pci_resources_query() to a common location to allow reuse by
the different drivers and over all the supported physical buses. Rename
it to mlxsw_core_resources_query().
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The minimal driver is chip independent and uses I2C bus for chip access.
Its purpose is to support chassis management on systems equipped with
Mellanox switch ASICs. For example from BMC (Board Management
Controller) device.

Expose a dummy netdev for each front panel port and implement basic
ethtool operations to obtain QSFP/SFP module info through ethtool.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace "mlxsw_minimal" by "mlxsw_m" in order to improve code
readability.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the implementation of ethtool module callbacks - .get_module_info()
and .get_module_eeprom() - to a common location to allow reuse by the
different mlxsw drivers.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

genphy_no_soft_reset and gen10g_no_soft_reset are both the same no-ops,
one is enough.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gen10g_read_status is deprecated, therefore stop exporting it.
We don't want to encourage anybody to use it.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ETHTOOL_LINK_MODE_10000baseT_Full_BIT is set anyway in the supported
and advertising bitmap because it's part of PHY_10GBIT_FEATURES.
And all users of gen10g_config_init use PHY_10GBIT_FEATURES.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

phy_suspend() and phy_resume() are no-ops anyway if no callback is
defined. Therefore we don't need these stubs.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we have it let's use genphy_c45_aneg_done() in phy_aneg_done().
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Quectel EG12 (module)/EM12 (M.2 card) is a Cat. 12 LTE modem. The modem
behaves in the same way as the EP06, so the "set DTR"-quirk must be
applied and the diagnostic-interface check performed. Since the
diagnostic-check now applies to more modems, I have renamed the function
from quectel_ep06_diag_detected() to quectel_diag_detected().
Signed-off-by: NKristian Evensen <kristian.evensen@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ports 9 and 10 don't have internal PHY's but are (dependent on the
version) SERDES/SGMII/XAUI/RXAUI ports.

v2:
- fix it for all 88E6x90 family members

Fixes: bc393155 ("net: dsa: mv88e6xxx: Add number of internal PHYs")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make logging of an ethernet address more consistent with
the rest of the kernel.

Miscellanea:

The %02hx use also did not quite match the u8 definition
of addr though that did not actually matter given normal
integer promotion rules.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When testing another issue I faced the problem that
mv88e6xxx_port_setup_mac() failed due to DUPLEX_UNKNOWN being passed
as argument to mv88e6xxx_port_set_duplex(). We should handle this case
gracefully and return -EOPNOTSUPP, like e.g. mv88e6xxx_port_set_speed()
is doing it.

Fixes: 7f1ae07b ("net: dsa: mv88e6xxx: add port duplex setter")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement support for the XDP_REDIRECT action.

The redirected frame is transmitted and confirmed on the regular Tx/Tx
conf queues. Frame is marked with the "XDP" type in the software
annotation, since it requires special treatment.

We don't have good hardware support for TX batching, so the
XDP_XMIT_FLUSH flag doesn't make a difference for now; ndo_xdp_xmit
performs the actual Tx operation on the spot.
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We write different metadata information in the software annotation
area of Tx frames, depending on frame type. Make this more explicit
by introducing a type field and separate structures for single buffer
and scatter-gather frames.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When macb device is suspended and system is powered down, the clocks
are removed and hence macb should be closed gracefully and restored
upon resume. This patch does the same by switching off the net device,
suspending phy and performing necessary cleanup of interrupts and BDs.
Upon resume, all these are reinitialized again.

Reset of macb device is done only when GEM is not a wake device.
Even when gem is a wake device, tx queues can be stopped and ptp device
can be closed (tsu clock will be disabled in pm_runtime_suspend) as
wake event detection has no dependency on this.
Signed-off-by: NKedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: NHarini Katakam <harini.katakam@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add runtime pm functions and move clock handling there.
Add runtime PM calls to mdio functions to allow for active mdio bus.
Signed-off-by: NShubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: NHarini Katakam <harini.katakam@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TSU clock needs to be enabled/disabled as per support in devicetree
and it should also be controlled during suspend/resume (WOL has no
dependency on this clock).
Signed-off-by: NHarini Katakam <harini.katakam@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the while loop in MDIO read/write functions with a timeout.
In addition, add a check for MDIO bus busy before initiating a new
operation as well to make sure there is no ongoing MDIO operation.
Signed-off-by: NShubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: NSai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: NHarini Katakam <harini.katakam@xilinx.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add KSZ9893 switch support in KSZ9477 driver.  This switch is similar to
KSZ9477 except the ingress tail tag has 1 byte instead of 2 bytes, so
KSZ9893 tagging will be used.

The XMII register that governs how the host port communicates with the
MAC also has different register definitions.
Signed-off-by: NTristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When Ocelot phy-mode is QSGMII, all 4 ports involved in
QSGMII shall be kept out of reset and
Tx lanes shall be enabled to pass the data.

Fixes: a556c76a ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: NKavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: NSteen Hegelund <Steen.Hegelund@microchip.com>
Co-developed-by: NSteen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Despite what the datesheet says, the silicon implements the older way
of snapshoting the statistics. Change the op.

Reported-by: Chris.Healy@zii.aero
Tested-by: Chris.Healy@zii.aero
Fixes: 0ac64c39 ("net: dsa: mv88e6xxx: mv88e6161 uses mv88e6320 stats snapshot")
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds calls in the stop() helper to ensure both MACs and
both PCS blocks are set in reset when the user manually sets a port
down. This is done so that we have the exact same block reset states at
boot time and when a port is set down.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch sets both the XPCS and MPCS blocks in reset when they aren't
used. This is done both at boot time and when reconfiguring a port mode.
The advantage now is that only the PCS used is set out of reset when the
port is configured (10GKR uses the MCPS while RXAUI uses the XPCS).
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes sure both PPv2 MACs (GMAC + XLG MAC) are set in reset
while a port is reconfigured. This is done so that we make sure a MAC is
in a reset state when not used, as only one of the two will be set out
of reset after the port is configured properly.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reworks the way the XLG MAC is set in reset: the XLG MAC is
set in reset at probe time and taken out of this state only when used.
The idea is to move forward a situation where only the blocks used are
taken out of reset. This also has the effect to handle the GMAC and the
XLG MAC in a similar way (the GMAC already is set in reset at boot
time).
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch force the XLG MAC link state in the phylink link_up() and
link_down() helpers when not using in-band auto-negotiation. This mimics
what's already done for the GMAC and follows what's advised in the
phylink documentation.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>