Use a new flag that requires the netdev to be
UP and use it to check instead of coding the
check into all functions that require it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This makes nl80211 use the new genetlink
pre_doit/post_doit hooks for locking and
checking the interface/wiphy index.

This significantly reduces the code size
and the likelihood of locking errors.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Each family may have some amount of boilerplate
locking code that applies to most, or even all,
commands.

This allows a family to handle such things in
a more generic way, by allowing it to
 a) include private flags in each operation
 b) specify a pre_doit hook that is called,
    before an operation's doit() callback and
    may return an error directly,
 c) specify a post_doit hook that can undo
    locking or similar things done by pre_doit,
    and finally
 d) include two private pointers in each info
    struct passed between all these operations
    including doit(). (It's two because I'll
    need two in nl80211 -- can be extended.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If kzalloc() fails then return should return with -ENOMEM.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable WME QoS in IBSS mode by adding a WME information element to beacons and
probe respones and by checking for it and marking stations as WME capable if it
is present.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a frame is not meant to be sent as AMPDU or part of it the hw might
still decide to aggregate this frame if a previous frame started an
AMPDU. However, this will limit the usefulness of the reported tx rate
since the reported rate will be the one specified in the TXWI of the
first frame and thus it is not possible to reliably caculate the
number of retrys by substracting the reported tx rate from the tx rate
in the TXWI.

To fix this issue, only report the successful rate for frames that were
not meant to be aggregated but ended up in an aggregate.

Example:
Frame A (MCS7, AMPDU=1) B (MCS7, AMPDU=1) C (MCS12, AMDPU=0, PROBE_RATE)

Although frame C shoudn't be aggregated the hw might sill put it
into an AMPDU together with A and B. If the transmission succeeds the tx
status will contain MCS7 for all three frames. In that case we should
only report MCS7 as success rate and avoid reporting MCS12-MCS8 as
failed tx attempts as this will affect the future rate control
decisions.

This oddity might strike us in other scenarious as well but the most
common "wrong" report happened for frames used to probe a different tx
rate.

This improves the rate control decisions notable.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to lower the impact of probe rates don't send a frame as AMPDU
if the rate control algorithm sets IEEE80211_TX_CTL_RATE_CTRL_PROBE.
Otherwise a whole aggregate would be send with a probe rate which might
lead to numerous retries.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When rt2x00lib_enable_radio fails to enable the radio, rt2x00lib_start
will call rt2x00queue_uninitialize to uninitialize the queues. Since,
the queues are not initialized here but already in rt2x00lib_initialize
we shouldn't uninitialize the queues here. Otherwise, a consecutive call
to rt2x00lib_start will oops (see below) because it assumes the queues
are already initialized.

BUG: unable to handle kernel NULL pointer dereference at 00000010
IP: [<f8d2d901>] :rt2800pci:rt2800pci_clear_entry+0x1/0x40
*pde = 00000000
Oops: 0000 [#1] SMP
Modules linked in: ... rt2800pci ...

Pid: 5995, comm: hostapd Not tainted (2.6.27.8 #1)
EIP: 0060:[<f8d2d901>] EFLAGS: 00210246 CPU: 3
EIP is at rt2800pci_clear_entry+0x1/0x40 [rt2800pci]
EAX: 00000000 EBX: f698863c ECX: 00200296 EDX: f8d2dee0
ESI: f6988600 EDI: f5b6f000 EBP: 00000000 ESP: f6d75e4c
 DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process hostapd (pid: 5995, ti=f6d74000 task=f6ce2300 task.ti=f6d74000)
Stack: f698863c fa00eaec 00000000 f5b6f000 00000000 f7b67000 f5b6e280 fa00c629
      f5b6f000 00000000 fa00ca3d f7b67480 00000001 fa177d4c 01b6e890 f7b67000
      00000000 f7b67000 00000001 00001003 00001002 c066c366 f7b67000 c0668ad0
Call Trace:
 [<fa00eaec>] rt2x00queue_init_queues+0x5c/0x90 [rt2x00lib]
 [<fa00c629>] rt2x00lib_enable_radio+0x29/0xa0 [rt2x00lib]
 [<fa00ca3d>] rt2x00lib_start+0x5d/0xd0 [rt2x00lib]
 [<fa177d4c>] ieee80211_do_open+0x21c/0x510 [mac80211]
 [<c066c366>] dev_open+0x56/0xb0
 [<c0668ad0>] dev_set_rx_mode+0x20/0x40
 [<c066a67f>] dev_change_flags+0x7f/0x190
 [<c06b1495>] devinet_ioctl+0x515/0x690
 [<c0668d24>] __dev_get_by_name+0x74/0x90
 [<c065d3f0>] sock_ioctl+0xd0/0x240
 [<c065d320>] sock_ioctl+0x0/0x240
 [<c018179b>] vfs_ioctl+0x2b/0x90
 [<c0181a5b>] do_vfs_ioctl+0x25b/0x2a0
 [<c0181af6>] sys_ioctl+0x56/0x70
 [<c0103262>] syscall_call+0x7/0xb
 [<c0700000>] add_card+0xad0/0xba0
 =======================
Code: 83 78 08 0e 74 14 8b 02 8b 48 04 85 c9 0f 99 c0 0f b6 c0 c3 8d b6
      00 00 00 00 8b 02 8b 40 04 85 c0 0f 99 c0 0f b6 c0 c3 66 90 53 <8b>
      48 10 8b 58 08 8b 40 04 83 78 08 0e 74 15 8b 11 83 c2 04 8b
EIP: [<f8d2d901>] rt2800pci_clear_entry+0x1/0x40 [rt2800pci] SS:ESP 0068:f6d75e4c
---[ end trace cff9a5c094bb8837 ]---
Reported-by: NJoshua Smith <jesmith@kaon.com>
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During testing with AMPDUs it turned out that the rt2800 hw will aggregate
consecutive frames with the same RA and TID when the first frame in a
possible aggregate has set AMPDU=1 in the TXWI. If a following frame has
set AMPDU=0 in its TXWI it might sill end up in the aggregate of the
previous frame. Update the comment accordingly.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The TX_STA_FIFO contains some information for identifying
a outgoing frame, however matching by WCID and ACK status is
not sufficient to 100% identify the macthing queue_entry structure
(containing the SKB buffer) which belongs to the status report.

Within TX_STA_FIFO we have a 4-bit field named PACKETID, which is
currently used to encode the queue id. The queue ID is however
limited to values from 0 to 3, which means 2 bits are sufficient
to encode the value. With the remaining 2 bits we can encode a
partial queue_entry index number. The value of PACKETID is not
allowed to become 0, with the queue ID ranging from 0 to 3, at least
one of the bits for the entry identification must be 1.

That leaves us with 3 possible values we can still encode in the
bits. Altough this doesn't allow 100% accurate matching of the
TX_STA_FIFO queue to a queue_entry structure, it at least improves
the accuracy. This allows us to better detect if we have missed the
TX_STA_FIFO report, which in turn reduces the number of watchdog
warnings regarding the TX status timeout.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt61pci and rt2800 devices can use up to 7 different rates per tx frame.
However, the device uses a global fallback table. Hence, the rc
algortihm cannot specify multiple rates to try but the device is able to
report multiple rates (based on the retry table). Specify that behavior
by correctly setting max_report_rates and max_rates.

This makes rt2x00 and minstrel play nicer together.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some drivers cannot handle multiple retry rates specified by the rc
algorithm but instead use their own retry table (for example rt2800).
However, if such a device registers itself with a max_rates value of 1
the rc algorithm cannot make use of the extended information the device
can provide about retried rates. On the other hand, if a device
registers itself with a max_rates value > 1 the rc algorithm assumes
that the device can handle multi rate retries.

Fix this issue by introducing another hw parameter max_report_rates that
can be set to a different value then max_rates to indicate if a device
is capable of reporting more rates then specified in max_rates.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since rt2x00 USB devices have no chance to know when a beacon was sent
out in AP mode currently all broad- and multicast traffic is buffered in
mac80211 but never sent out at all.

Unfortunately we have no chance in sending the traffic out after a
DTIM beacon due to hw limitations. Hence, instead of never sending the
buffered traffic out better send it out immediately.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Reported-by: NLauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add the register definition CH_BUSY_STA_SEC for reading the busy time
on the secondary channel in HT40 mode. Also update the comments about
channel busy/idle time registers to express the used unit.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make use of the IEEE80211_TX_RC_DUP_DATA flag to duplicate a
transmission with legacy rates to both 20Mhz channels if set.
Also update the related comment in rt2800.h to describe the
behavior of the BW_40 flag for legacy rates.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During rx, rt2x00lib calls rt2800pci_fill_rxdone to read the RX
descriptor. At that time the skb is already dma unmapped but no new skb
was dma mapped for this entry again. However, rt2800pci_fill_rxdone also
moves the hw rx queue index, marking this entry to be available for
reuse. Since no new skb was dma mapped and also the previous skb was
unmapped this might lead to strange hw behavior.

To fix this issue move the hw rx queue index increment to
rt2800pci_clear_entry where a new skb was already dma mapped and can be
safely used by the hw.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since HT protection is now configurable via mac80211 we don't need this
special case for PCI devices anymore. The HT protection config will be
overwritten as soon as mac80211 sends us a HT operation mode. Hence,
bring the HT MM40 protection config in sync with the other HT protection
registers and initialize it to no protection.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the HT operation mode when mac80211 sends it to us and set
the different HT protection modes and rates accordingly. For now
only use CTS-to-self with OFDM 24M or CCK 11M when protection is
required.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix a check for dynamic SM PS mode in the STAs HT caps. Since a
value of 3 means "SM PS disabled" the previous check assumed in
that case that "dynamic SM PS" was enabled and as such prefixed
every MCS>7 frame with a unnecessary RTS/CTS exchange. Also,
the bit shift was done in the wrong direction.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch changes the way tx status reports are handled by rt2800pci.
Previously rt2800pci would sometimes lose tx status reports as the
TX_STA_FIFO register is a fifo of 16 entries that can overflow in case
we don't read it often/fast enough. Since interrupts are disabled in the
device during the execution of the interrupt thread it happend sometimes
under high network and CPU load that processing took too long and a few
tx status reports were dropped by the hw.

To fix this issue the TX_STA_FIFO register is read directly in the
interrupt handler and stored in a kfifo which is large enough to hold
all status reports of all used tx queues.

To process the status reports a new tasklet txstatus_tasklet is used.
Using the already used interrupt thread is not possible since we don't
want to disable the TX_FIFO_STATUS interrupt while processing them and
it is not possible to schedule the interrupt thread multiple times for
execution. A tasklet instead can be scheduled multiple times which
allows to leave the TX_FIFO_STATUS interrupt enabled while a previously
scheduled tasklet is still executing.

In short: All other interrupts are handled in the interrupt thread as
before. Only the TX_FIFO_STATUS interrupt is partly handled in the
interrupt handler and finished in the according tasklet.

One drawback of this patch is that it duplicates some code from
rt2800lib. However, that can be cleaned up in the future once the
rt2800usb and rt2800pci tx status handling converge more.

Using this patch on a Ralink RT3052 embedded board gives me a reliable
wireless connection even under high CPU and network load. I've
transferred several gigabytes without any queue lockups.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2800 devices use parts of the pariwise key table to store the beacon
frames for beacon 6 and 7. To not overwrite the beacon frame buffers
limit the number of entries we store in the pairwise key table to 222.

Also add some descriptive comments about this shared memory usage.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Source:
http://www.wikidevi.com/wiki/Intersil/p54/usb/windows

Cc: <stable@kernel.org>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Includes pkts/bytes that may have had errors, and includes
wireless headers when counting bytes.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds counters for tx and rx bytes, including any
errored packets as well as all wireless headers.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Acked-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Initialize the rate table for WDS interfaces, and
add cases to allow WDS packets to pass the xmit and receive
tests.
Signed-off-by: NBill Jordan <bjordan@rajant.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added a nl interface to set the peer bssid of a WDS interface.
Signed-off-by: NBill Jordan <bjordan@rajant.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable WDS for the ath9k driver.
Signed-off-by: NBill Jordan <bjordan@rajant.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On association to an AP, after receiving beacons, the beacon_crc value is set.
The beacon_crc value is not reset in disassociation, but the BSS data may be
expired at a later point. When associating again, it's possible that a
beacon for the AP is not received, resulting in the beacon_ies to remain NULL.

After association, further beacons will not update the beacon data, as the
crc value of the beacon has not changed, and the beacon_crc still holds a
value matching the beacon. The beacon_ies will remain forever null.

One of the results of this is that WLAN power save cannot be entered, the STA
will remain foreven in active mode.

Fix this by adding a validation flag for the beacon_crc, which is cleared on
association.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move ieee80211_scan_cancel() and all other related code to
ieee80211_restart_work() as ieee80211_restart_hw() is intended to be
callable from any context.

Fix a bug that RTNL lock is not taken during ieee80211_cancel_scan().

Take local->mtx before WARN(test_bit(SCAN_HW_SCANNING, &local->scanning)
to prevent the race condition with __ieee80211_start_scan() described
here: http://marc.info/?l=linux-wireless&m=128516716810537&w=2Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the ath9k debugging feature 'wiphy' the current channel used by the
station is incorrectly displayed.This is because the channels available
are sequentially mapped from numbers 0 to 37.This mapping cannot be
changed as the channel number is also used as an array index
          This fix solves the above problem by calculating the channel
number from center frequency.
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The percal struct and bitmask for the initial DC calibration are not
used anywhere, so they can be removed.

Signed-off-by: Felix Fietkau <nbd@openwrt.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since the regulatory code touches the channel array, it needs to be
copied for each device instance. That way the original channel array
can also be made const.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org [all]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add missing unlocking of the wiphy in set_channel,
and don't try to unlock a non-existing wiphy in
set_cqm.

Cc: stable@kernel.org [2.6.35+]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Support up to 4 virtual APs and as many virtual STA interfaces
as desired.

This patch is ported forward from a patch that Patrick McHardy
did for me against 2.6.31.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Acked-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The net/cfg80211.h header file isn't exported to
userspace, so there's no need for any kind of
__KERNEL__ protection in it. If it was exported,
everything else in it would need protection as
well, not just the logging stuff ...

Cc:Joe Perches <joe@perches.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable management frame transmission and subscribing
to management frames through nl80211 in both cfg80211
and mac80211. Also update a few places that I forgot
to update for P2P-client mode previously, and fix a
small bug with non-action frames in this API.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>