This patch makes the various mach dirs that use the plat-orion time
code pass in timer and bridge addresses explicitly, instead of having
plat-orion get those values by including a mach dir include file --
the latter mechanism is problematic if you want to support multiple
ARM platforms in the same kernel image.
Signed-off-by: NLennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

Add support for the QNAP NAS devices based on Marvell's 6282 Kirkwood
chip (TS-119P+, TS-219P+ and TS-419P+).  The differences to the 6281
based devices are:
 - Ethernet PHY address
 - GPIOs used for buttons (TS-119P+/TS-219P+)
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Acked-by: NSaeed Bishara <saeed.bishara@gmail.com>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.

The various declarations were removed using the following script:

  grep -rl MACHINE_START arch/arm | xargs \
  sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'

[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>

This patch extends the kirkwood's PCIe support up to 2 controllers as in the 6282 devices.
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

MPP44 can be used to differentiate between one-bay (TS-11x) and
two-bay (TS-21x) devices.

According to an engineer from QNAP, the setting of MPP44 depends
on the firmware rather than hardware.  Presumably, this means
that you could fake the MPP44 value by changing the boot loader.
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

Add MPP definitions for Marvell Kirkwood 88F6282 revision.
Update some defines to reflect datasheet's MPP names.
Signed-off-by: NBenjamin Zores <benjamin.zores@alcatel-lucent.com>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

Remove the code duplication found in the setup files of TS-219 and
TS-41x.
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Add two new models from QNAP to the help text.  They are compatible
with the TS-119/TS-219 and therefore supported by the current code.
The only difference is that they have less RAM (256 MB instead of
512 MB), a slower CPU (800 MHz vs 1.2 GHz) and a plastic case.
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

MPP36 is used on the QNAP TS-11x/TS-21x devices to indicate how
much RAM there is: it's high for 512 MB RAM (TS-x19) and low for
256 MB (TS-x10).  While this may not be very useful, let's add
it for completeness.
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Initialize PCI/PCIe on the QNAP TS-119, TS-219 and TS-219P hardware
allowing the use of the discrete eSATA controller connected to the PCIe
bus in the TS-219P.
Signed-off-by: NJohn Holland <john.holland@cellent-fs.de>
Tested-by: NThomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

For the QNAP TS-119 and TS-219 the wrong MPPs were used for the SATA
activity/presence LEDs. The new settings make these LEDs work as
expected.
Signed-off-by: NThomas Reitmayr <treitmayr@devbase.at>
Tested-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Add support for the QNAP TS-119 and TS-219 Turbo NAS devices.
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>