Skip to content

K
Kernel

openeuler / Kernel
接近 2 年 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 08 8月, 2018 1 次提交
  3. 07 2月, 2018 1 次提交
    • S
      be2net: Handle transmit completion errors in Lancer · ffc39620
      由 Suresh Reddy 提交于 
      If the driver receives a TX CQE with status as 0x1 or 0x9 or 0xb,
the completion indexes should not be used. The driver must stop
consuming CQEs from this TXQ/CQ. The TXQ from this point on-wards
to be in a bad state. Driver should destroy and recreate the TXQ.

0x1: LANCER_TX_COMP_LSO_ERR
0x9 LANCER_TX_COMP_SGE_ERR
0xb: LANCER_TX_COMP_PARITY_ERR

Reset the adapter if driver sees this error in TX completion. Also
adding sge error counter in ethtool stats.
Signed-off-by: NSuresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ffc39620
  5. 03 1月, 2017 1 次提交
  7. 08 9月, 2016 1 次提交
    • S
      be2net: Support UE recovery in BEx/Skyhawk adapters · 710f3e59
      由 Sriharsha Basavapatna 提交于 
      This patch supports recovery from UEs caused due to Transient Parity
Errors (TPE), in BE2, BE3 and Skyhawk adapters. This change avoids
system reboot when such errors occur. The driver recovers from these
errors such that the adapter resumes full operational status as prior
to the UE.

Following is the list of changes in the driver to support this:

o The driver registers its UE recoverable capability with ARM FW at init
time. This also allows the driver to know if the feature is supported in
the FW.

o As the UE recovery requires precise time bound processing, the driver
creates its own error recovery work queue with a single worker thread (per
module, shared across functions).

o Each function runs an error detection task at an interval of 1 second as
required by the FW. The error detection logic already exists for BEx/SH,
but it now runs in the context of a separate worker thread.

o When an error is detected by the task, if it is recoverable, the PF0
driver instance initiates a soft reset, while other PF driver instances
wait for the reset to complete and the chip to become ready. Once
the chip is ready, all driver instances including PF0, resume to
reinitialize the respective functions.

o The PF0 driver checks for some recovery criteria, to determine if the
recovery can be initiated. If the criteria is not met, the PF0 driver does
not initiate a soft reset, it retains the existing behavior to stop
further processing and requires a reboot to get the chip to operational
state again.

o To allow each function to share the workq, while also making progress in
its recovery process, a per-function recovery state machine is used.
The per-function tasks avoid blocking operations like msleep() while in
this state machine (until reinit state) and instead reschedule for the
required delay.

o With these changes, the existing error recovery code for Lancer also
runs in the context of the new worker thread.
Signed-off-by: NSriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      710f3e59
  9. 27 6月, 2016 2 次提交
  11. 08 6月, 2016 1 次提交
    • S
      be2net: Enable Wake-On-LAN from shutdown for Skyhawk · 45f13df7
      由 Sriharsha Basavapatna 提交于 
      Skyhawk does support wake-up from ACPI shutdown state - S5, provided the
platform supports it (like Auxiliary power source etc). The changes listed
below are done to fix this.

1) There's no need to defer the HW configuration of WOL to be_suspend().
Remove this in be_suspend() and move it to be_set_wol() ethtool function
so it is configured directly in the context of ethtool. This automatically
takes care of the shutdown case.

2) The driver incorrectly uses WOL_CAP field in the FW response to
get_acpi_wol_cap() command, to determine if WOL is enabled. Instead the
driver must rely on the macaddr field in the response to infer WOL state.

3) In be_get_config() during init, if we find that WOL is enabled in FW,
call pci_enable_wake() to enable pmcsr.pme_en bit. This is needed to
support persistent WOL configuration provided by the FW in some platforms.

4) Remove code in be_set_wol() that writes to PCICFG_PM_CONTROL_OFFSET
to set pme_en bit; pci_enable_wake() sets that.

Fixes: 028991e4 ("Enabling Wake-on-LAN is not supported in S5 state")
Signed-off-by: NSriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      45f13df7
  13. 08 2月, 2016 1 次提交
  15. 31 12月, 2015 1 次提交
  17. 19 11月, 2015 1 次提交
  19. 17 11月, 2015 2 次提交
  21. 16 10月, 2015 1 次提交
  23. 30 7月, 2015 1 次提交
  25. 11 7月, 2015 1 次提交
  27. 08 6月, 2015 1 次提交
  29. 15 5月, 2015 1 次提交
  31. 10 5月, 2015 2 次提交
  33. 05 3月, 2015 1 次提交
  35. 25 1月, 2015 1 次提交
  37. 06 1月, 2015 1 次提交
    • S
      be2net: support TX batching using skb->xmit_more flag · 5f07b3c5
      由 Sathya Perla 提交于 
      This patch uses skb->xmit_more flag to batch TX requests.
TX is flushed either when xmit_more is false or there is
no more space in the TXQ.

Skyhawk-R and BEx chips require an even number of wrbs to be posted.
So, when a batch of TX requests is accumulated, the last header wrb
may need to be fixed with an extra dummy wrb.

This patch refactors be_xmit() routine as a sequence of be_xmit_enqueue()
and be_xmit_flush() calls. The Tx completion code is also
updated to be able to unmap/free a batch of skbs rather than a single
skb.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      5f07b3c5
  39. 09 12月, 2014 1 次提交
    • E
      ethtool: Support for configurable RSS hash function · 892311f6
      由 Eyal Perry 提交于 
      This patch extends the set/get_rxfh ethtool-options for getting or
setting the RSS hash function.

It modifies drivers implementation of set/get_rxfh accordingly.

This change also delegates the responsibility of checking whether a
modification to a certain RX flow hash parameter is supported to the
driver implementation of set_rxfh.

User-kernel API is done through the new hfunc bitmask field in the
ethtool_rxfh struct. A bit set in the hfunc field is corresponding to an
index in the new string-set ETH_SS_RSS_HASH_FUNCS.

Got approval from most of the relevant driver maintainers that their
driver is using Toeplitz, and for the few that didn't answered, also
assumed it is Toeplitz.

Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Shradha Shah <sshah@solarflare.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      892311f6
  41. 23 9月, 2014 8 次提交
  43. 14 9月, 2014 3 次提交
  45. 03 9月, 2014 3 次提交
  47. 03 8月, 2014 1 次提交
  49. 18 7月, 2014 1 次提交
  51. 19 5月, 2014 1 次提交