Add struct kvm_vmx, which wraps struct kvm, and a helper to_kvm_vmx()
that retrieves 'struct kvm_vmx *' from 'struct kvm *'.  Move the VMX
specific variables out of kvm_arch and into kvm_vmx.
Signed-off-by: NSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Add kvm_x86_ops->set_identity_map_addr and set ept_identity_map_addr
in VMX specific code so that ept_identity_map_addr can be moved out
of 'struct kvm_arch' in a future patch.
Signed-off-by: NSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Define kvm_arch_[alloc|free]_vm in x86 as pass through functions
to new kvm_x86_ops vm_alloc and vm_free, and move the current
allocation logic as-is to SVM and VMX.  Vendor specific alloc/free
functions set the stage for SVM/VMX wrappers of 'struct kvm',
which will allow us to move the growing number of SVM/VMX specific
member variables out of 'struct kvm_arch'.
Signed-off-by: NSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Commit 2bb8cafe ("KVM: vVMX: signal failure for nested VMEntry if
emulation_required", 2018-03-12) introduces a new error path which does
not set *entry_failure_code.  Fix that to avoid a leak of L0 stack to L1.
Reported-by: NRadim Krčmář <rkrcmar@redhat.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

When L1 IOAPIC redirection-table is written, a request of
KVM_REQ_SCAN_IOAPIC is set on all vCPUs. This is done such that
all vCPUs will now recalc their IOAPIC handled vectors and load
it to their EOI-exitmap.

However, it could be that one of the vCPUs is currently running
L2. In this case, load_eoi_exitmap() will be called which would
write to vmcs02->eoi_exit_bitmap, which is wrong because
vmcs02->eoi_exit_bitmap should always be equal to
vmcs12->eoi_exit_bitmap. Furthermore, at this point
KVM_REQ_SCAN_IOAPIC was already consumed and therefore we will
never update vmcs01->eoi_exit_bitmap. This could lead to remote_irr
of some IOAPIC level-triggered entry to remain set forever.

Fix this issue by delaying the load of EOI-exitmap to when vCPU
is running L1.

One may wonder why not just delay entire KVM_REQ_SCAN_IOAPIC
processing to when vCPU is running L1. This is done in order to handle
correctly the case where LAPIC & IO-APIC of L1 is pass-throughed into
L2. In this case, vmcs12->virtual_interrupt_delivery should be 0. In
current nVMX implementation, that results in
vmcs02->virtual_interrupt_delivery to also be 0. Thus,
vmcs02->eoi_exit_bitmap is not used. Therefore, every L2 EOI cause
a #VMExit into L0 (either on MSR_WRITE to x2APIC MSR or
APIC_ACCESS/APIC_WRITE/EPT_MISCONFIG to APIC MMIO page).
In order for such L2 EOI to be broadcasted, if needed, from LAPIC
to IO-APIC, vcpu->arch.ioapic_handled_vectors must be updated
while L2 is running. Therefore, patch makes sure to delay only the
loading of EOI-exitmap but not the update of
vcpu->arch.ioapic_handled_vectors.
Reviewed-by: NArbel Moshe <arbel.moshe@oracle.com>
Reviewed-by: NKrish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: NLiran Alon <liran.alon@oracle.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

vmx_save_host_state() is only called from kvm_arch_vcpu_ioctl_run() so
the context is pretty well defined and as we're past 'swapgs' MSR_GS_BASE
should contain kernel's GS base which we point to irq_stack_union.

Add new kernelmode_gs_base() API, irq_stack_union needs to be exported
as KVM can be build as module.
Acked-by: NAndy Lutomirski <luto@kernel.org>
Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

vmx_save_host_state() is only called from kvm_arch_vcpu_ioctl_run() so
the context is pretty well defined. Read MSR_{FS,KERNEL_GS}_BASE from
current->thread after calling save_fsgs() which takes care of
X86_BUG_NULL_SEG case now and will do RD[FG,GS]BASE when FSGSBASE
extensions are exposed to userspace (currently they are not).
Acked-by: NAndy Lutomirski <luto@kernel.org>
Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Allow to disable pause loop exit/pause filtering on a per VM basis.

If some VMs have dedicated host CPUs, they won't be negatively affected
due to needlessly intercepted PAUSE instructions.

Thanks to Jan H. Schönherr's initial patch.

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: NWanpeng Li <wanpengli@tencent.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

If host CPUs are dedicated to a VM, we can avoid VM exits on HLT.
This patch adds the per-VM capability to disable them.

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: NWanpeng Li <wanpengli@tencent.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Allowing a guest to execute MWAIT without interception enables a guest
to put a (physical) CPU into a power saving state, where it takes
longer to return from than what may be desired by the host.

Don't give a guest that power over a host by default. (Especially,
since nothing prevents a guest from using MWAIT even when it is not
advertised via CPUID.)

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: NWanpeng Li <wanpengli@tencent.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

VMware exposes the following Pseudo PMCs:
0x10000: Physical host TSC
0x10001: Elapsed real time in ns
0x10002: Elapsed apparent time in ns

For more info refer to:
https://www.vmware.com/files/pdf/techpaper/Timekeeping-In-VirtualMachines.pdf

VMware allows access to these Pseduo-PMCs even when read via RDPMC
in Ring3 and CR4.PCE=0. Therefore, commit modifies x86 emulator
to allow access to these PMCs in this situation. In addition,
emulation of these PMCs were added to kvm_pmu_rdpmc().
Signed-off-by: NArbel Moshe <arbel.moshe@oracle.com>
Signed-off-by: NLiran Alon <liran.alon@oracle.com>
Reviewed-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

If KVM enable_vmware_backdoor module parameter is set,
the commit change VMX to now intercept #GP instead of being directly
deliviered from CPU to guest.

It is done to support access to VMware Backdoor I/O ports
even if TSS I/O permission denies it.
In that case:
1. A #GP will be raised and intercepted.
2. #GP intercept handler will simulate I/O port access instruction.
3. I/O port access instruction simulation will allow access to VMware
backdoor ports specifically even if TSS I/O permission bitmap denies it.

Note that the above change introduce slight performance hit as now #GPs
are now not deliviered directly from CPU to guest but instead
cause #VMExit and instruction emulation.
However, this behavior is introduced only when enable_vmware_backdoor
KVM module parameter is set.
Signed-off-by: NLiran Alon <liran.alon@oracle.com>
Reviewed-by: NNikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

If KVM enable_vmware_backdoor module parameter is set,
the commit change VMX to now intercept #GP instead of being directly
deliviered from CPU to guest.

It is done to support access to VMware backdoor I/O ports
even if TSS I/O permission denies it.
In that case:
1. A #GP will be raised and intercepted.
2. #GP intercept handler will simulate I/O port access instruction.
3. I/O port access instruction simulation will allow access to VMware
backdoor ports specifically even if TSS I/O permission bitmap denies it.

Note that the above change introduce slight performance hit as now #GPs
are not deliviered directly from CPU to guest but instead
cause #VMExit and instruction emulation.
However, this behavior is introduced only when enable_vmware_backdoor
KVM module parameter is set.
Signed-off-by: NLiran Alon <liran.alon@oracle.com>
Reviewed-by: NNikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Access to VMware backdoor ports is done by one of the IN/OUT/INS/OUTS
instructions. These ports must be allowed access even if TSS I/O
permission bitmap don't allow it.

To handle this, VMX/SVM will be changed in future commits
to intercept #GP which was raised by such access and
handle it by calling x86 emulator to emulate instruction.
If it was one of these instructions, the x86 emulator already handles
it correctly (Since commit "KVM: x86: Always allow access to VMware
backdoor I/O ports") by not checking these ports against TSS I/O
permission bitmap.

One may wonder why checking for specific instructions is necessary
as we can just forward all #GPs to the x86 emulator.
There are multiple reasons for doing so:

1. We don't want the x86 emulator to be reached easily
by guest by just executing an instruction that raises #GP as that
exposes the x86 emulator as a bigger attack surface.

2. The x86 emulator is incomplete and therefore certain instructions
that can cause #GP cannot be emulated. Such an example is "INT x"
(opcode 0xcd) which reaches emulate_int() which can only emulate
the instruction if vCPU is in real-mode.
Signed-off-by: NLiran Alon <liran.alon@oracle.com>
Reviewed-by: NNikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Next commits are going introduce support for accessing VMware backdoor
ports even though guest's TSS I/O permissions bitmap doesn't allow
access. This mimic VMware hypervisor behavior.

In order to support this, next commits will change VMX/SVM to
intercept #GP which was raised by such access and handle it by calling
the x86 emulator to emulate instruction. Since commit "KVM: x86:
Always allow access to VMware backdoor I/O ports", the x86 emulator
handles access to these I/O ports by not checking these ports against
the TSS I/O permission bitmap.

However, there could be cases that CPU rasies a #GP on instruction
that fails to be disassembled by the x86 emulator (Because of
incomplete implementation for example).

In those cases, we would like the #GP intercept to just forward #GP
as-is to guest as if there was no intercept to begin with.
However, current emulator code always queues #UD exception in case
emulator fails (including disassembly failures) which is not what is
wanted in this flow.

This commit addresses this issue by adding a new emulation_type flag
that will allow the #GP intercept handler to specify that it wishes
to be aware when instruction emulation fails and doesn't want #UD
exception to be queued.
Signed-off-by: NLiran Alon <liran.alon@oracle.com>
Reviewed-by: NNikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

VMware allows access to these ports even if denied
by TSS I/O permission bitmap. Mimic behavior.
Signed-off-by: NLiran Alon <liran.alon@oracle.com>
Reviewed-by: NNikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Support access to VMware backdoor requires KVM to intercept #GP
exceptions from guest which introduce slight performance hit.
Therefore, control this support by module parameter.

Note that module parameter is exported as it should be consumed by
kvm_intel & kvm_amd to determine if they should intercept #GP or not.

This commit doesn't change semantics.
It is done as a preparation for future commits.
Signed-off-by: NLiran Alon <liran.alon@oracle.com>
Reviewed-by: NNikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Add kvm_fast_pio() to consolidate duplicate code in VMX and SVM.
Unexport kvm_fast_pio_in() and kvm_fast_pio_out().
Suggested-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Fast emulation of processor I/O for IN was disabled on x86 (both VMX
and SVM) some years ago due to a buggy implementation.  The addition
of kvm_fast_pio_in(), used by SVM, re-introduced (functional!) fast
emulation of IN.  Piggyback SVM's work and use kvm_fast_pio_in() on
VMX instead of performing full emulation of IN.
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Fail a nested VMEntry with EXIT_REASON_INVALID_STATE if L2 guest state
is invalid, i.e. vmcs12 contained invalid guest state, and unrestricted
guest is disabled in L0 (and by extension disabled in L1).

WARN_ON_ONCE in handle_invalid_guest_state() if we're attempting to
emulate L2, i.e. nested_run_pending is true, to aid debug in the
(hopefully unlikely) scenario that we somehow skip the nested VMEntry
consistency check, e.g. due to a L0 bug.

Note: KVM relies on hardware to detect the scenario where unrestricted
guest is enabled in L0 but disabled in L1 and vmcs12 contains invalid
guest state, i.e. checking emulation_required in prepare_vmcs02 is
required only to handle the case were unrestricted guest is disabled
in L0 since L0 never actually attempts VMLAUNCH/VMRESUME with vmcs02.
Signed-off-by: NSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

CR3 load/store exiting are always off when unrestricted guest
is enabled.  WARN on the associated CR3 VMEXIT to detect code
that would re-introduce CR3 load/store exiting for unrestricted
guest.
Signed-off-by: NSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

Now CR3 is not forced to a host-controlled value when paging is
disabled in an unrestricted guest, CR3 load/store exiting can be
left disabled (for an unrestricted guest).  And because CR0.WP
and CR4.PAE/PSE are also not force to host-controlled values,
all of ept_update_paging_mode_cr0() is no longer needed, i.e.
skip ept_update_paging_mode_cr0() for an unrestricted guest.

Because MOV CR3 no longer exits when paging is disabled for an
unrestricted guest, vmx_decache_cr3() must always read GUEST_CR3
from the VMCS for an unrestricted guest.
Signed-off-by: NSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

CR4.PAE - Unrestricted guest can only be enabled when EPT is
enabled, and vmx_set_cr4() clears hardware CR0.PAE based on
the guest's CR4.PAE, i.e. CR4.PAE always follows the guest's
value when unrestricted guest is enabled.

CR4.PSE - Unrestricted guest no longer uses the identity mapped
IA32 page tables since CR0.PG can be cleared in hardware, thus
there is no need to set CR4.PSE when paging is disabled in the
guest (and EPT is enabled).

Define KVM_VM_CR4_ALWAYS_ON_UNRESTRICTED_GUEST (to X86_CR4_VMXE)
and use it in lieu of KVM_*MODE_VM_CR4_ALWAYS_ON when unrestricted
guest is enabled, which removes the forcing of CR4.PAE.

Skip the manipulation of CR4.PAE/PSE for EPT when unrestricted
guest is enabled, as CR4.PAE isn't forced and so doesn't need to
be manually cleared, and CR4.PSE does not need to be set when
paging is disabled since the identity mapped IA32 page tables
are not used.
Signed-off-by: NSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

Unrestricted guest can only be enabled when EPT is enabled, and
when EPT is enabled, ept_update_paging_mode_cr0() will clear
hardware CR0.WP based on the guest's CR0.WP, i.e. CR0.WP always
follows the guest's value when unrestricted guest is enabled.
Signed-off-by: NSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

An unrestricted guest can run with hardware CR0.PG==0, i.e.
IA32 paging disabled, in which case there is no need to load
the guest's CR3 with identity mapped IA32 page tables since
hardware will effectively ignore CR3.  If unrestricted guest
is enabled, don't configure the identity mapped IA32 page
table and always load the guest's desired CR3.
Signed-off-by: NSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

An unrestricted guest can run with CR0.PG==0 and/or CR0.PE==0,
e.g. it can run in Real Mode without requiring host emulation.
The RM TSS is only used for emulating RM, i.e. it will never
be used when unrestricted guest is enabled and so doesn't need
to be configured.
Signed-off-by: NSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

Hyper-V 2016 on KVM with SynIC enabled doesn't boot with the following
trace:

    kvm_entry:            vcpu 0
    kvm_exit:             reason MSR_WRITE rip 0xfffff8000131c1e5 info 0 0
    kvm_hv_synic_set_msr: vcpu_id 0 msr 0x40000090 data 0x10000 host 0
    kvm_msr:              msr_write 40000090 = 0x10000 (#GP)
    kvm_inj_exception:    #GP (0x0)

KVM acts according to the following statement from TLFS:

"
11.8.4 SINTx Registers
...
Valid values for vector are 16-255 inclusive. Specifying an invalid
vector number results in #GP.
"

However, I checked and genuine Hyper-V doesn't #GP when we write 0x10000
to SINTx. I checked with Microsoft and they confirmed that if either the
Masked bit (bit 16) or the Polling bit (bit 18) is set to 1, then they
ignore the value of Vector. Make KVM act accordingly.
Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

When a new vector is written to SINx we update vec_bitmap/auto_eoi_bitmap
but we forget to remove old vector from these masks (in case it is not
present in some other SINTx).
Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

Nested Hyper-V/Windows guest running on top of KVM will use TSC page
clocksource in two cases:
- L0 exposes invariant TSC (CPUID.80000007H:EDX[8]).
- L0 provides Hyper-V Reenlightenment support (CPUID.40000003H:EAX[13]).

Exposing invariant TSC effectively blocks migration to hosts with different
TSC frequencies, providing reenlightenment support will be needed when we
start migrating nested workloads.

Implement rudimentary support for reenlightenment MSRs. For now, these are
just read/write MSRs with no effect.
Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

... to avoid having a stale value when handling an EPT misconfig for MMIO
regions.

MMIO regions that are not passed-through to the guest are handled through
EPT misconfigs. The first time a certain MMIO page is touched it causes an
EPT violation, then KVM marks the EPT entry to cause an EPT misconfig
instead. Any subsequent accesses to the entry will generate an EPT
misconfig.

Things gets slightly complicated with nested guest handling for MMIO
regions that are not passed through from L0 (i.e. emulated by L0
user-space).

An EPT violation for one of these MMIO regions from L2, exits to L0
hypervisor. L0 would then look at the EPT12 mapping for L1 hypervisor and
realize it is not present (or not sufficient to serve the request). Then L0
injects an EPT violation to L1. L1 would then update its EPT mappings. The
EXIT_QUALIFICATION value for L1 would come from exit_qualification variable
in "struct vcpu". The problem is that this variable is only updated on EPT
violation and not on EPT misconfig. So if an EPT violation because of a
read happened first, then an EPT misconfig because of a write happened
afterwards. The L0 hypervisor will still contain exit_qualification value
from the previous read instead of the write and end up injecting an EPT
violation to the L1 hypervisor with an out of date EXIT_QUALIFICATION.

The EPT violation that is injected from L0 to L1 needs to have the correct
EXIT_QUALIFICATION specially for the access bits because the individual
access bits for MMIO EPTs are updated only on actual access of this
specific type. So for the example above, the L1 hypervisor will keep
updating only the read bit in the EPT then resume the L2 guest. The L2
guest would end up causing another exit where the L0 *again* will inject
another EPT violation to L1 hypervisor with *again* an out of date
exit_qualification which indicates a read and not a write. Then this
ping-pong just keeps happening without making any forward progress.

The behavior of mapping MMIO regions changed in:

   commit a340b3e2 ("kvm: Map PFN-type memory regions as writable (if possible)")

... where an EPT violation for a read would also fixup the write bits to
avoid another EPT violation which by acciddent would fix the bug mentioned
above.

This commit fixes this situation and ensures that the access bits for the
exit_qualifcation is up to date. That ensures that even L1 hypervisor
running with a KVM version before the commit mentioned above would still
work.

( The description above assumes EPT to be available and used by L1
  hypervisor + the L1 hypervisor is passing through the MMIO region to the L2
  guest while this MMIO region is emulated by the L0 user-space ).

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: x86@kernel.org
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NKarimAllah Ahmed <karahmed@amazon.de>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

The type 'enum kvm_reg_ex' is an extension of 'enum kvm_reg', however
the extension is only semantical and the compiler doesn't know about the
relationship between the two types. In kvm_pdptr_read() a value of the
extended type is passed to kvm_x86_ops->cache_reg(), which expects a
value of the base type. Clang raises the following warning about the
type mismatch:

arch/x86/kvm/kvm_cache_regs.h:44:32: warning: implicit conversion from
  enumeration type 'enum kvm_reg_ex' to different enumeration type
  'enum kvm_reg' [-Wenum-conversion]
    kvm_x86_ops->cache_reg(vcpu, VCPU_EXREG_PDPTR);

Cast VCPU_EXREG_PDPTR to 'enum kvm_reg' to make the compiler happy.
Signed-off-by: NMatthias Kaehlcke <mka@chromium.org>
Reviewed-by: NGuenter Roeck <groeck@chromium.org>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

Devices which use level-triggered interrupts under Windows 2016 with
Hyper-V role enabled don't work: Windows disables EOI broadcast in SPIV
unconditionally. Our in-kernel IOAPIC implementation emulates an old IOAPIC
version which has no EOI register so EOI never happens.

The issue was discovered and discussed a while ago:
https://www.spinics.net/lists/kvm/msg148098.html

While this is a guest OS bug (it should check that IOAPIC has the required
capabilities before disabling EOI broadcast) we can workaround it in KVM:
advertising DIRECTED_EOI with in-kernel IOAPIC makes little sense anyway.
Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

Add support for AMD Core Performance counters in the guest. The base
event select and counter MSRs are changed. In addition, with the core
extension, there are 2 extra counters available for performance
measurements for a total of 6.

With the new MSRs, the logic to map them to the gp_counters[] is changed.
New functions are added to check the validity of the get/set MSRs.

If the guest has the X86_FEATURE_PERFCTR_CORE cpuid flag set, the number
of counters available to the vcpu is set to 6. It the flag is not set
then it is 4.
Signed-off-by: NJanakarajan Natarajan <Janakarajan.Natarajan@amd.com>
[Squashed "Expose AMD Core Perf Extension flag to guests" - Radim.]
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

Add the EventSelect and Counter MSRs for AMD Core Perf Extension.
Signed-off-by: NJanakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

For testing the exitless interrupt support it turned out useful to
have separate counters for inject and delivery of I/O interrupt.
While at it do the same for all interrupt types. For timer
related interrupts (clock comparator and cpu timer) we even had
no delivery counters. Fix this as well. On this way some counters
are being renamed to have a similar name.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: NCornelia Huck <cohuck@redhat.com>

This counter can be used for administration, debug or test purposes.
Suggested-by: NVladislav Mironov <mironov@de.ibm.com>
Signed-off-by: NQingFeng Hao <haoqf@linux.vnet.ibm.com>
Reviewed-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: NCornelia Huck <cohuck@redhat.com>
Reviewed-by: NDavid Hildenbrand <david@redhat.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>

The S390 architecture does not support any graphics hardware,
but with the latest support for Virtio GPU in Linux and Virtio
GPU emulation in QEMU, it's possible to enable graphics for
S390 using the Virtio GPU device.

To enable display we need to enable the Linux Virtual Terminal (VT)
layer for S390. But the VT subsystem initializes quite early
at boot so we need a dummy console driver till the Virtio GPU
driver is initialized and we can run the framebuffer console.

The framebuffer console over a Virtio GPU device can be run
in combination with the serial SCLP console (default on S390).
The SCLP console can still be accessed by management applications
(eg: via Libvirt's virsh console).
Signed-off-by: NFarhan Ali <alifm@linux.vnet.ibm.com>
Acked-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: NThomas Huth <thuth@redhat.com>
Message-Id: <e23b61f4f599ba23881727a1e8880e9d60cc6a48.1519315352.git.alifm@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A case statement in kvm_s390_shadow_tables uses fallthrough annotations
which are not recognized by gcc because they are hidden within a block.
Move these annotations out of the block to fix (W=1) warnings like below:

arch/s390/kvm/gaccess.c: In function 'kvm_s390_shadow_tables':
arch/s390/kvm/gaccess.c:1029:26: warning: this statement may fall through [-Wimplicit-fallthrough=]
  case ASCE_TYPE_REGION1: {
                          ^
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: NCornelia Huck <cohuck@redhat.com>
Reviewed-by: NDavid Hildenbrand <david@redhat.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>

We want to count IO exit requests in kvm_stat. At the same time
we can get rid of the handle_noop function.
Reviewed-by: NDavid Hildenbrand <david@redhat.com>
Reviewed-by: NCornelia Huck <cohuck@redhat.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>

use_cmma in kvm_arch means that the KVM hypervisor is allowed to use
cmma, whereas use_cmma in the mm context means cmm has been used before.
Let's rename the context one to uses_cmm, as the vm does use
collaborative memory management but the host uses the cmm assist
(interpretation facility).

Also let's introduce use_pfmfi, so we can remove the pfmfi disablement
when we activate cmma and rather not activate it in the first place.
Signed-off-by: NJanosch Frank <frankja@linux.vnet.ibm.com>
Message-Id: <1518779775-256056-2-git-send-email-frankja@linux.vnet.ibm.com>
Reviewed-by: NDavid Hildenbrand <david@redhat.com>
Reviewed-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>