One of OCE's optimizations is acception of broadcast probe responses.
Accept broadcast probe responses but don't set
NL80211_EXT_FEATURE_ACCEPT_BCAST_PROBE_RESP. Because a device's firmware
may filter out the broadcast probe resp - drivers should set this flag.
Signed-off-by: NRoee Zamir <roee.zamir@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
[johannes: make accepting broadcast conditional on the nl80211 scan
 flag that was added for that specific purpose]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add Optimized Connectivity Experience (OCE) scan and capability flags.
Some of them unique to OCE and some are stand alone.
And add scan flags to enable/disable them.
Signed-off-by: NRoee Zamir <roee.zamir@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When NL80211_ATTR_WIPHY_CHANNEL_TYPE is given, nl80211 would parse the
channel definition the old way, discarding NL80211_ATTR_CENTER_FREQ1,
NL80211_ATTR_CENTER_FREQ2 etc. However, it is possible that user space
added both NL80211_ATTR_WIPHY_CHANNEL_TYPE and NL80211_ATTR_CENTER_FREQ1
or NL80211_ATTR_CENTER_FREQ2 assuming that all settings would be honored.

In such a case, validate that NL80211_ATTR_CENTER_FREQ1 and
NL80211_ATTR_CENTER_FREQ2 values match the channel configuration,
as otherwise user space would assume that the desired configuration was
applied.

For example, when trying to start ap with
NL80211_ATTR_WIPHY_CHANNEL_TYPE = NL80211_CHAN_HT40MINUS,
NL80211_ATTR_WIPHY_FREQ = 5180 and NL80211_ATTR_CENTER_FREQ1 = 5250
without this fix, the ap will start on channel 36 (center_freq1 will be
corrected to 5180).  With this fix, we will throw an error instead.
Signed-off-by: NTova Mussai <tova.mussai@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to split off IEs from the ones obtained
from userspace, if they were already split off, so for
example IEs that went before HT don't have to be listed
again to go before VHT. Simplify the code here so it's
clearer.

While at it, also clarify the comments regarding the DMG
(60 GHz) elements.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Current ieee80211_ie_split() implementation doesn't
account for elements that are sub-elements of the
EXTENSION IE. To extend support to these IEs as well,
treat the WLAN_EID_EXTENSION ids in the %ids array
as indicating that the next id in the array is a
sub-element of the EXTENSION IE.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

For AP_VLAN and monitor interfaces we'll never use the TXQs
we allocated, so avoid doing so.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

HTB qdisc overlimits counter is properly increased, but we have no per
class counter, meaning it is difficult to diagnose HTB problems.

This patch adds this counter, visible in "tc -s class show dev eth0",
with current iproute2.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NDenys Fedoryshchenko <nuclearcat@nuclearcat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pointer tcm is being initialized and is never read, it is only being used
to determine the size of struct tcmsg.  Clean this up by removing
variable tcm and explicitly using the sizeof struct tcmsg rather than *tcm.
Cleans up clang warning:

warning: Value stored to 'tcm' during its initialization is never read
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Roman Yeryomin says:

====================
korina: performance fixes and cleanup

Changes from v1:
- use GRO instead of increasing ring size
- use NAPI_POLL_WEIGHT instead of defining own NAPI_WEIGHT
- optimize rx descriptor flags processing
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRoman Yeryomin <roman@advem.lv>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRoman Yeryomin <roman@advem.lv>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRoman Yeryomin <roman@advem.lv>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Performance gain when receiving locally is 55->95Mbps and 50->65Mbps for NAT.
Signed-off-by: NRoman Yeryomin <roman@advem.lv>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRoman Yeryomin <roman@advem.lv>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRoman Yeryomin <roman@advem.lv>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When such interrupts occur there is not much we can do.
Dropping the whole ring doesn't help and only produces high packet loss.
If we just ignore the interrupt the mac will drop one or few packets instead of the whole ring.
Also this will lower the irq handling load and increase performance.
Signed-off-by: NRoman Yeryomin <roman@advem.lv>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modify baycom driver to use the new parallel port device model.
Signed-off-by: NSudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-By: NThomas Sailer <t.sailer@alumni.ethz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

uf_info.regs is resource_size_t i.e. phys_addr_t that can be either u32
or u64 according to CONFIG_PHYS_ADDR_T_64BIT.

The printk format is thus adaptet to u64 and the regs value cast to u64
to take both u32 and u64 into account.
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pci_map_single functions are obsolete. So replace them with
dma_map_single functions.
Signed-off-by: NZhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: updates 2017-09-18

first batch of patches for 4.15. One larger item in there is Hans'
addition of new configuration options for flexible packet processing
('VNIC characteristics'). The patch descriptions have all the details.
Please apply.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cppcheck reports the following for drivers/s390/net/qeth_core.h:

    warning - line 1560 - Function 'qeth_do_send_packet' argument order
    different:
    declaration 'card, queue, skb, hdr, hd_len, offset, elements'
    definition  'card, queue, skb, hdr, offset, hd_len, elements_needed'.

Match the naming in the function's declaration against its definition.
Signed-off-by: NJens Remus <jremus@linux.vnet.ibm.com>
Reviewed-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the overly complicated VLAN processing from the L3 RX handler into
its l3_rebuild_skb() helper. No change in functionality.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Properly return any error encountered during VLAN processing to the
the caller.
Resulting change in behaviour: if SETVLAN fails while registering a
new VLAN ID, the stack no longer creates the corresponding vlan device.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the right helpers to create/remove all attribute groups in one go.
Suggested-by: NHans Wippel <hwippel@linux.vnet.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Locking the output queue prior to TX is needed on OSA devices,
to synchronize against a packing flush from the TX completion code
(via qeth_check_outbound_queue()).
But send_packet_fast() is only used for IQDs, which don't do packing.
So remove the locking, and apply some easy cleanups.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Storing the number of input buffers into 'i' has no effect, it is
immediately re-assigned in the next line.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HiperSockets allow configuring so called VNIC Characteristics (VNICC)
that influence how the underlying hardware handles packets. For VNICCs,
additional commands for getting and setting timeouts are available.
Currently, the learning VNICC uses these commands.

* Learning VNICC: If learning is enabled on a qeth device, the device
  learns the source MAC addresses of outgoing packets and incoming
  packets to those learned MAC addresses are received.

For learning, the timeout specifies the idle period in seconds, after
which the underlying hardware removes a learned MAC address again.

This patch adds support for the IPA commands that are required to get
and set the current timeout values for the learning VNIC characteristic.
Also, it introduces the sysfs interface that allows users to configure
the timeout.
Signed-off-by: NHans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HiperSocket devices allow enabling and disabling so called VNIC
Characteristics (VNICC) that influence how the underlying hardware
handles packets. These VNICCs are:

* Flooding VNICC: Flooding allows specifying if packets to unknown
  destination MAC addresses are received by the qeth device.

* Multicast flooding VNICC: Multicast flooding allows specifying if
  packets to multicast MAC addresses are received by the qeth device.

* Learning VNICC: If learning is enabled on a qeth device, the device
  learns the source MAC addresses of outgoing packets and incoming
  packets to those learned MAC addresses are received.

* Takeover setvmac VNICC: If takeover setvmac is configured on a qeth
  device, the MAC address of this device can be configured on a
  different qeth device with the setvmac IPA command.

* Takeover by learning VNICC: If takeover learning is enabled on a qeth
  device, the MAC address of this device can be learned (learning VNICC)
  on a different qeth device.

* BridgePort invisible VNICC: If BridgePort invisible is enabled on a
  qeth device, (1) packets from this device are not sent to a BridgePort
  enabled qeth device and (2) packets coming from a BridgePort enabled
  qeth device are not received by this device.

* Receive broadcast VNICC: Receive broadcast allows configuring if a
  qeth device receives packets with the broadcast destination MAC
  address.

This patch adds support for the IPA commands that are required to enable
and disable these VNIC characteristics on qeth devices. As a
prerequisite, it also adds the query commands IPA command.

The query commands IPA command allows requesting the supported commands
for each characteristic from the underlying hardware.

Additionally, this patch provides users with a sysfs user interface to
enable/disable the VNICCs mentioned above.
Signed-off-by: NHans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VNIC Characteristics (VNICC) are features of HiperSockets that define
how packets are handled by the underlying network hardware. For example,
if the VNICC flooding is configured on a qeth device, ethernet frames to
unknown destination MAC addresses are received.

Currently, there is support for seven VNICCs: flooding, multicast
flooding, receive broadcast, learning, takeover learning, takeover
setvmac, bridge invisible. Also, six IPA commands exist for configuring
VNICCs on a qeth device: query characteristics, query commands, enable
characteristic, disable characteristic, set timeout, get timeout.

This patch adds the basic code infrastructure for VNICC support to qeth.
It allows querying VNICC support from the underlying hardware. To this
end, it adds:

* basic message formats for IPA commands
* basic data structures
* basic error handling
* query characteristics IPA command support

The query characteristics IPA command allows requesting the currently
supported and currently enabled VNIC characteristics from the underlying
hardware.

Support for the other IPA commands and for the configuration of VNICCs
is added in follow-up patches together with the respective user
interface functions.
Signed-off-by: NHans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new compatible string for the R8A77995 (R-Car D3) RAVB.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Global function ipv6_rcv_saddr_equal and static functions
ipv6_rcv_saddr_equal and ipv4_rcv_saddr_equal currently return int.

bool is slightly more descriptive for these functions so change
their return type from int to bool.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

R-Car V3M (R8A77970) SoC also has the R-Car gen3 compatible EtherAVB
device, so document  the SoC specific bindings.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add RTL8201F phy-id and the related functions to the driver.

The original patch is as follows:
https://patchwork.kernel.org/patch/2538341/Signed-off-by: NJongsung Kim <neidhard.kim@lge.com>
Signed-off-by: NJassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: NKunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This renames the definition of page select register from
RTL8211F_PAGE_SELECT to RTL821x_PAGE_SELECT to use it across models.
Signed-off-by: NKunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dummy device name is enumerated by the kernel, let user space be aware
of the naming scheme used by dummy devices:
(visible in /sys/class/net/<iface>/name_assign_type).
Signed-off-by: NZhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the #ifdef into the static void function so that the use
of DBGUNDO is validated when FASTRETRANS_DEBUG <= 1.

Remove the now unnecessary #else and #define DBGUNDO.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull UBI updates from Richard Weinberger:
 "Minor improvements"

* tag 'upstream-4.14-rc1' of git://git.infradead.org/linux-ubifs:
  UBI: Fix two typos in comments
  ubi: fastmap: fix spelling mistake: "invalidiate" -> "invalidate"
  ubi: pr_err() strings should end with newlines
  ubi: pr_err() strings should end with newlines
  ubi: pr_err() strings should end with newlines

Pull UML updates from Richard Weinberger:

 - minor improvements

 - fixes for Debian's new gcc defaults (pie enabled by default)

 - fixes for XSTATE/XSAVE to make UML work again on modern systems

* 'for-linus-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: return negative in tuntap_open_tramp()
  um: remove a stray tab
  um: Use relative modversions with LD_SCRIPT_DYN
  um: link vmlinux with -no-pie
  um: Fix CONFIG_GCOV for modules.
  Fix minor typos and grammar in UML start_up help
  um: defconfig: Cleanup from old Kconfig options
  um: Fix FP register size for XSTATE/XSAVE

Pull networking fixes from David Miller:

 1) Fix hotplug deadlock in hv_netvsc, from Stephen Hemminger.

 2) Fix double-free in rmnet driver, from Dan Carpenter.

 3) INET connection socket layer can double put request sockets, fix
    from Eric Dumazet.

 4) Don't match collect metadata-mode tunnels if the device is down,
    from Haishuang Yan.

 5) Do not perform TSO6/GSO on ipv6 packets with extensions headers in
    be2net driver, from Suresh Reddy.

 6) Fix scaling error in gen_estimator, from Eric Dumazet.

 7) Fix 64-bit statistics deadlock in systemport driver, from Florian
    Fainelli.

 8) Fix use-after-free in sctp_sock_dump, from Xin Long.

 9) Reject invalid BPF_END instructions in verifier, from Edward Cree.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
  mlxsw: spectrum_router: Only handle IPv4 and IPv6 events
  Documentation: link in networking docs
  tcp: fix data delivery rate
  bpf/verifier: reject BPF_ALU64|BPF_END
  sctp: do not mark sk dumped when inet_sctp_diag_fill returns err
  sctp: fix an use-after-free issue in sctp_sock_dump
  netvsc: increase default receive buffer size
  tcp: update skb->skb_mstamp more carefully
  net: ipv4: fix l3slave check for index returned in IP_PKTINFO
  net: smsc911x: Quieten netif during suspend
  net: systemport: Fix 64-bit stats deadlock
  net: vrf: avoid gcc-4.6 warning
  qed: remove unnecessary call to memset
  tg3: clean up redundant initialization of tnapi
  tls: make tls_sw_free_resources static
  sctp: potential read out of bounds in sctp_ulpevent_type_enabled()
  MAINTAINERS: review Renesas DT bindings as well
  net_sched: gen_estimator: fix scaling error in bytes/packets samples
  nfp: wait for the NSP resource to appear on boot
  nfp: wait for board state before talking to the NSP
  ...