Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 03 4月, 2017 2 次提交
  3. 26 3月, 2017 1 次提交
  5. 17 3月, 2017 1 次提交
  7. 26 1月, 2017 2 次提交
  9. 19 1月, 2017 1 次提交
    • T
      net: Remove usage of net_device last_rx member · 4a7c9726
      由 Tobias Klauser 提交于 
      The network stack no longer uses the last_rx member of struct net_device
since the bonding driver switched to use its own private last_rx in
commit 9f242738 ("bonding: use last_arp_rx in slave_last_rx()").

However, some drivers still (ab)use the field for their own purposes and
some driver just update it without actually using it.

Previously, there was an accompanying comment for the last_rx member
added in commit 4dc89133 ("net: add a comment on netdev->last_rx")
which asked drivers not to update is, unless really needed. However,
this commend was removed in commit f8ff080d ("bonding: remove
useless updating of slave->dev->last_rx"), so some drivers added later
on still did update last_rx.

Remove all usage of last_rx and switch three drivers (sky2, atp and
smc91c92_cs) which actually read and write it to use their own private
copy in netdev_priv.

Compile-tested with allyesconfig and allmodconfig on x86 and arm.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NEric Dumazet <edumazet@google.com>
Reviewed-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4a7c9726
  11. 30 10月, 2016 3 次提交
  13. 27 10月, 2016 1 次提交
    • S
      batman-adv: Revert "use core MTU range checking in misc drivers" · 701470ba
      由 Sven Eckelmann 提交于 
      The maximum MTU is defined via the slave devices of an batman-adv
interface. Thus it is not possible to calculate the max_mtu during the
creation of the batman-adv device when no slave devices are attached. Doing
so would for example break non-fragmentation setups which then
(incorrectly) allow an MTU of 1500 even when underlying device cannot
transport 1500 bytes + batman-adv headers.

Checking the dynamically calculated max_mtu via the minimum of the slave
devices MTU during .ndo_change_mtu is also used by the bridge interface.

Cc: Jarod Wilson <jarod@redhat.com>
Fixes: b3e3893e ("net: use core MTU range checking in misc drivers")
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      701470ba
  15. 21 10月, 2016 1 次提交
    • J
      net: use core MTU range checking in misc drivers · b3e3893e
      由 Jarod Wilson 提交于 
      firewire-net:
- set min/max_mtu
- remove fwnet_change_mtu

nes:
- set max_mtu
- clean up nes_netdev_change_mtu

xpnet:
- set min/max_mtu
- remove xpnet_dev_change_mtu

hippi:
- set min/max_mtu
- remove hippi_change_mtu

batman-adv:
- set max_mtu
- remove batadv_interface_change_mtu
- initialization is a little async, not 100% certain that max_mtu is set
  in the optimal place, don't have hardware to test with

rionet:
- set min/max_mtu
- remove rionet_change_mtu

slip:
- set min/max_mtu
- streamline sl_change_mtu

um/net_kern:
- remove pointless ndo_change_mtu

hsi/clients/ssi_protocol:
- use core MTU range checking
- remove now redundant ssip_pn_set_mtu

ipoib:
- set a default max MTU value
- Note: ipoib's actual max MTU can vary, depending on if the device is in
  connected mode or not, so we'll just set the max_mtu value to the max
  possible, and let the ndo_change_mtu function continue to validate any new
  MTU change requests with checks for CM or not. Note that ipoib has no
  min_mtu set, and thus, the network core's mtu > 0 check is the only lower
  bounds here.

mptlan:
- use net core MTU range checking
- remove now redundant mpt_lan_change_mtu

fddi:
- min_mtu = 21, max_mtu = 4470
- remove now redundant fddi_change_mtu (including export)

fjes:
- min_mtu = 8192, max_mtu = 65536
- The max_mtu value is actually one over IP_MAX_MTU here, but the idea is to
  get past the core net MTU range checks so fjes_change_mtu can validate a
  new MTU against what it supports (see fjes_support_mtu in fjes_hw.c)

hsr:
- min_mtu = 0 (calls ether_setup, max_mtu is 1500)

f_phonet:
- min_mtu = 6, max_mtu = 65541

u_ether:
- min_mtu = 14, max_mtu = 15412

phonet/pep-gprs:
- min_mtu = 576, max_mtu = 65530
- remove redundant gprs_set_mtu

CC: netdev@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: Stefan Richter <stefanr@s5r6.in-berlin.de>
CC: Faisal Latif <faisal.latif@intel.com>
CC: linux-rdma@vger.kernel.org
CC: Cliff Whickman <cpw@sgi.com>
CC: Robin Holt <robinmholt@gmail.com>
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Marek Lindner <mareklindner@neomailbox.ch>
CC: Simon Wunderlich <sw@simonwunderlich.de>
CC: Antonio Quartulli <a@unstable.cc>
CC: Sathya Prakash <sathya.prakash@broadcom.com>
CC: Chaitra P B <chaitra.basappa@broadcom.com>
CC: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
CC: MPT-FusionLinux.pdl@broadcom.com
CC: Sebastian Reichel <sre@kernel.org>
CC: Felipe Balbi <balbi@kernel.org>
CC: Arvid Brodin <arvid.brodin@alten.se>
CC: Remi Denis-Courmont <courmisch@gmail.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b3e3893e
  17. 17 10月, 2016 1 次提交
  19. 09 8月, 2016 3 次提交
  21. 04 7月, 2016 1 次提交
  23. 30 6月, 2016 3 次提交
  25. 29 6月, 2016 1 次提交
  27. 10 5月, 2016 6 次提交
  29. 05 5月, 2016 1 次提交
  31. 04 5月, 2016 2 次提交
  33. 24 4月, 2016 1 次提交
  35. 23 2月, 2016 2 次提交
  37. 10 2月, 2016 1 次提交
  39. 02 2月, 2016 4 次提交
  41. 28 8月, 2015 1 次提交
  43. 25 8月, 2015 1 次提交