Modify p9_virtio_request() and req_done() functions to support
additional payload sent down to the transport layer through
tc->pubuf and tc->pkbuf.
Signed-off-by: NVenkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: NEric Van Hensbergen <ericvh@gmail.com>

This will be used by the transport layer to determine the out going
request type. Transport layer uses this information to correctly
place the mapped pages in the PDU. Patches following this will make
use of this to achieve zero copy.
Signed-off-by: NVenkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: NEric Van Hensbergen <ericvh@gmail.com>

This patch prepares p9_fcall structure for zero copy. Added
fields send the payload buffer information to the transport layer.
In addition it adds a 'private' field for the transport layer to
store mapped/pinned page information so that it can be freed/unpinned
during req_done.

This patch also creates trans_common.[ch] to house helper functions.
It adds the following helper functions.

p9_release_req_pages - Release pages after the transaction.
p9_nr_pages - Return number of pages needed to accomodate the payload.
payload_gup - Translates user buffer into kernel pages.
Signed-off-by: NVenkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: NEric Van Hensbergen <ericvh@gmail.com>

Current code sets access=user as default for all protocol versions.
This patch chagnes it to "client" only for dotl.

User can always specify particular access mode with -o access= option.
No change there.
Signed-off-by: NVenkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: NEric Van Hensbergen <ericvh@gmail.com>

The mount option access=client is overloaded as it assumes acl too.
Adding posixacl option to enable POSIX ACLs makes it explicit and clear.
Also it is convenient in the future to add other types of acls like richacls.

Ideally, the access mode 'client' should be just like V9FS_ACCESS_USER
except it underscores the location of access check.
Traditional 9P protocol lets the server perform access checks but with
this mode, all the access checks will be performed on the client itself.
Server just follows the client's directive.
Signed-off-by: NVenkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: NEric Van Hensbergen <ericvh@gmail.com>

If the kernel is not compiled with CONFIG_9P_FS_POSIX_ACL and the
mount option is specified to enable ACLs current code fails the mount.
This patch brings the behavior inline with other filesystems like ext3
by proceeding with the mount and log a warning to syslog.
Signed-off-by: NVenkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: NEric Van Hensbergen <ericvh@gmail.com>

With create/mkdir/mknod in non cached mode we initialize the inode using
v9fs_get_inode. v9fs_get_inode doesn't initialize the cache inode value
to NULL.  This is causing to trip on BUG_ON in v9fs_get_cached_acl.
Fix is to initialize acls to NULL and not to leave them in ACL_NOT_CACHED
state.
Signed-off-by: NVenkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: NEric Van Hensbergen <ericvh@gmail.com>
Reviewed-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>

In v9fs_get_acl() if __v9fs_get_acl() gets only one of the
dacl/pacl we are not releasing it.
Signed-off-by: NVenkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: NEric Van Hensbergen <ericvh@gmail.com>
Reviewed-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300:
  MN10300: atomic_read() should ensure it emits a load
  MN10300: The SMP_ICACHE_INV_FLUSH_RANGE IPI command does not exist
  MN10300: Proper use of macros get_user() in the case of incremented pointers

* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
  MIPS: Alchemy: Fix reset for MTX-1 and XXS1500
  MIPS: MTX-1: Make au1000_eth probe all PHY addresses
  MIPS: Jz4740: Add HAVE_CLK
  MIPS: Move idle task creation to work queue
  MIPS, Perf-events: Use unsigned delta for right shift in event update
  MIPS, Perf-events: Work with the new callchain interface
  MIPS, Perf-events: Fix event check in validate_event()
  MIPS, Perf-events: Work with the new PMU interface
  MIPS, Perf-events: Work with irq_work
  MIPS: Fix always CONFIG_LOONGSON_UART_BASE=y
  MIPS: Loongson: Fix potentially wrong string handling
  MIPS: Fix GCC-4.6 'set but not used' warning in arch/mips/mm/init.c
  MIPS: Fix GCC-4.6 'set but not used' warning in ieee754int.h
  MIPS: Remove unused code from arch/mips/kernel/syscall.c
  MIPS: Fix GCC-4.6 'set but not used' warning in signal*.c
  MIPS: MSP: Fix MSP71xx bpci interrupt handler return value
  MIPS: Select R4K timer lib for all MSP platforms
  MIPS: Loongson: Remove ad-hoc cmdline default
  MIPS: Clear the correct flag in sysmips(MIPS_FIXADE, ...).
  MIPS: Add an unreachable return statement to satisfy buggy GCCs.
  ...

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: ce4100: Set pci ops via callback instead of module init
  x86/mm: Fix pgd_lock deadlock
  x86/mm: Handle mm_fault_error() in kernel space
  x86: Don't check for BIOS corruption in first 64K when there's no need to

This reverts the parent commit.  I hate doing that, but it's generating
some discussion ("half of it is right"), and since I am planning on
doing the 2.6.38 release later today we can punt it to stable if
required. Let's not rock the boat right now.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

oom_kill_process() starts with victim_points == 0.  This means that
(most likely) any child has more points and can be killed erroneously.

Also, "children has a different mm" doesn't match the reality, we should
check child->mm != t->mm.  This check is not exactly correct if t->mm ==
NULL but this doesn't really matter, oom_kill_task() will kill them
anyway.

Note: "Kill all processes sharing p->mm" in oom_kill_task() is wrong
too.
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since commit 32fd6901 (MIPS: Alchemy: get rid of common/reset.c)
Alchemy-based boards use their own reset function. For MTX-1 and XXS1500,
the reset function pokes at the BCSR.SYSTEM_RESET register, but this does
not work. According to Bruno Randolf, this was not tested when written.

Previously, the generic au1000_restart() routine called the board specific
reset function, which for MTX-1 and XXS1500 did not work, but finally made
a jump to the reset vector, which really triggers a system restart. Fix
reboot for both targets by jumping to the reset vector.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2093/Acked-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When au1000_eth probes the MII bus for PHY address, if we do not set
au1000_eth platform data's phy_search_highest_address, the MII probing
logic will exit early and will assume a valid PHY is found at address 0.
For MTX-1, the PHY is at address 31, and without this patch, the link
detection/speed/duplex would not work correctly.

CC: stable@kernel.org
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2111/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Jz4740 supports the clock framework but doesn't have HAVE_CLK defined,
so define it!
Signed-off-by: NMaurus Cuelenaere <mcuelenaere@gmail.com>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2112/Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

To avoid forking usermode thread when creating an idle task, move fork_idle
to a work queue.

If kernel starts with maxcpus= option which does not bring all available
cpus online at boot time, idle tasks for offline cpus are not created. If
later offline cpus are hotplugged through sysfs, __cpu_up is called in
the context of the user task, and fork_idle copies its non-zero mm
pointer.  This causes BUG() in per_cpu_trap_init.

This also avoids issues with resource limits of the CPU writing to sysfs,
containers, maybe others.
Signed-off-by: NMaksim Rayskiy <mrayskiy@broadcom.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2070/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Leverage the commit for ARM by Will Deacon:

- 446a5a8b
    ARM: 6205/1: perf: ensure counter delta is treated as unsigned

    Hardware performance counters on ARM are 32-bits wide but atomic64_t
    variables are used to represent counter data in the hw_perf_event structure.

    The armpmu_event_update function right-shifts a signed 64-bit delta variable
    and adds the result to the event count. This can lead to shifting in sign-bits
    if the MSB of the 32-bit counter value is set. This results in perf output
    such as:

     Performance counter stats for 'sleep 20':

     18446744073460670464  cycles             <-- 0xFFFFFFFFF12A6000
            7783773  instructions             #      0.000 IPC
                465  context-switches
                161  page-faults
            1172393  branches

       20.154242147  seconds time elapsed

    This patch ensures that the delta value is treated as unsigned so that the
    right shift sets the upper bits to zero.
Acked-by: NWill Deacon <will.deacon@arm.com>
Acked-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NDeng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: a.p.zijlstra@chello.nl
To: fweisbec@gmail.com
To: will.deacon@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: wuzhangjin@gmail.com
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: matt@console-pimps.org
Cc: sshtylyov@mvista.com
Patchwork: http://patchwork.linux-mips.org/patch/2015/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This is the MIPS part of the following commits by Frederic Weisbecker:

- f72c1a93
    perf: Factorize callchain context handling

    Store the kernel and user contexts from the generic layer instead
    of archs, this gathers some repetitive code.

- 56962b44
    perf: Generalize some arch callchain code

    - Most archs use one callchain buffer per cpu, except x86 that needs
      to deal with NMIs. Provide a default perf_callchain_buffer()
      implementation that x86 overrides.

    - Centralize all the kernel/user regs handling and invoke new arch
      handlers from there: perf_callchain_user() / perf_callchain_kernel()
      That avoid all the user_mode(), current->mm checks and so...

    - Invert some parameters in perf_callchain_*() helpers: entry to the
      left, regs to the right, following the traditional (dst, src).

- 70791ce9
    perf: Generalize callchain_store()

    callchain_store() is the same on every archs, inline it in
    perf_event.h and rename it to perf_callchain_store() to avoid
    any collision.

    This removes repetitive code.

- c1a65932
    perf: Drop unappropriate tests on arch callchains

    Drop the TASK_RUNNING test on user tasks for callchains as
    this check doesn't seem to make any sense.

    Also remove the tests for !current that is not supposed to
    happen and current->pid as this should be handled at the
    generic level, with exclude_idle attribute.
Reported-by: NWu Zhangjin <wuzhangjin@gmail.com>
Acked-by: NFrederic Weisbecker <fweisbec@gmail.com>
Acked-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NDeng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: a.p.zijlstra@chello.nl
To: will.deacon@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: dengcheng.zhu@gmail.com
Cc: matt@console-pimps.org
Cc: sshtylyov@mvista.com
Patchwork: http://patchwork.linux-mips.org/patch/2014/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Ignore events that are in off/error state or belong to a different PMU.

This patch originates from the following commit for ARM by Will Deacon:

- 65b4711f
    ARM: 6352/1: perf: fix event validation

    The validate_event function in the ARM perf events backend has the
    following problems:

    1.) Events that are disabled count towards the cost.
    2.) Events associated with other PMUs [for example, software events or
        breakpoints] do not count towards the cost, but do fail validation,
        causing the group to fail.

    This patch changes validate_event so that it ignores events in the
    PERF_EVENT_STATE_OFF state or that are scheduled for other PMUs.
Acked-by: NWill Deacon <will.deacon@arm.com>
Acked-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NDeng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: a.p.zijlstra@chello.nl
To: fweisbec@gmail.com
To: will.deacon@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: wuzhangjin@gmail.com
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: dengcheng.zhu@gmail.com
Cc: matt@console-pimps.org
Cc: sshtylyov@mvista.com
Cc: ddaney@caviumnetworks.com
Patchwork: http://patchwork.linux-mips.org/patch/2013/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This is the MIPS part of the following commits by Peter Zijlstra:

- a4eaf7f1
    perf: Rework the PMU methods

    Replace pmu::{enable,disable,start,stop,unthrottle} with
    pmu::{add,del,start,stop}, all of which take a flags argument.

    The new interface extends the capability to stop a counter while
    keeping it scheduled on the PMU. We replace the throttled state with
    the generic stopped state.

    This also allows us to efficiently stop/start counters over certain
    code paths (like IRQ handlers).

    It also allows scheduling a counter without it starting, allowing for
    a generic frozen state (useful for rotating stopped counters).

    The stopped state is implemented in two different ways, depending on
    how the architecture implemented the throttled state:

     1) We disable the counter:
        a) the pmu has per-counter enable bits, we flip that
        b) we program a NOP event, preserving the counter state

     2) We store the counter state and ignore all read/overflow events

For MIPSXX, the stopped state is implemented in the way of 1.b as above.

- 33696fc0
    perf: Per PMU disable

    Changes perf_disable() into perf_pmu_disable().

- 24cd7f54
    perf: Reduce perf_disable() usage

    Since the current perf_disable() usage is only an optimization,
    remove it for now. This eases the removal of the __weak
    hw_perf_enable() interface.

- b0a873eb
    perf: Register PMU implementations

    Simple registration interface for struct pmu, this provides the
    infrastructure for removing all the weak functions.

- 51b0fe39
    perf: Deconstify struct pmu

    sed -ie 's/const struct pmu\>/struct pmu/g' `git grep -l "const struct pmu\>"`
Reported-by: NWu Zhangjin <wuzhangjin@gmail.com>
Acked-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NDeng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: a.p.zijlstra@chello.nl
To: fweisbec@gmail.com
To: will.deacon@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: wuzhangjin@gmail.com
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: dengcheng.zhu@gmail.com
Cc: matt@console-pimps.org
Cc: sshtylyov@mvista.com
Cc: ddaney@caviumnetworks.com
Patchwork: http://patchwork.linux-mips.org/patch/2012/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This is the MIPS part of the following commit by Peter Zijlstra:

- e360adbe
    irq_work: Add generic hardirq context callbacks

    Provide a mechanism that allows running code in IRQ context. It is
    most useful for NMI code that needs to interact with the rest of the
    system -- like wakeup a task to drain buffers.

    Perf currently has such a mechanism, so extract that and provide it as
    a generic feature, independent of perf so that others may also
    benefit.

    The IRQ context callback is generated through self-IPIs where
    possible, or on architectures like powerpc the decrementer (the
    built-in timer facility) is set to generate an interrupt immediately.

    Architectures that don't have anything like this get to do with a
    callback from the timer tick. These architectures can call
    irq_work_run() at the tail of any IRQ handlers that might enqueue such
    work (like the perf IRQ handler) to avoid undue latencies in
    processing the work.

For MIPSXX, we need to call irq_work_run() at the tail of the perf IRQ
handler as described above.
Reported-by: NWu Zhangjin <wuzhangjin@gmail.com>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NDeng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: fweisbec@gmail.com
To: will.deacon@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: matt@console-pimps.org
Cc: sshtylyov@mvista.com,
Patchwork: http://patchwork.linux-mips.org/patch/2011/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2055/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This error was reported by cppcheck:
arch/mips/loongson/common/machtype.c:56: error: Dangerous usage of 'str' (strncpy doesn't always 0-terminate it)

If strncpy copied MACHTYPE_LEN bytes, the destination string str
was not terminated.

The patch adds one more byte to str and makes sure that this byte is
always 0.
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Arnaud Patard <apatard@mandriva.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2053/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Under some combinations of CONFIG_*, lastpfn in page_is_ram is 'set
but not used'.  Mark it as __maybe_unused to quiet the warning/error.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2033/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

GCC-4.6 can find more unused code than previous versions could.

In the case of arch/mips/math-emu/ieee754int.h, the COMPXSP and
COMPXDP macros are used in several places, but a couple of them leave
xs unused.  The easiest thing to do is mark it as __maybe_unused to
quiet the warning.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2032/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The variable arg3 in _sys_sysmips() is unused.  Remove it.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2034/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

GCC-4.6 can find more unused code than previous versions could.

In the case of protected_restore_fp_context{,32}, the variable tmp is
really used.  Its use is tricky in that we really care about the side
effects of the __put_user() calls.  So we must mark tmp with
__maybe_unused to quiet the warning.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2035/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NAnoop P A <anoop.pa@gmail.com>
To: Ben Hutchings <ben@decadent.org.uk>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1804/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NAnoop P A <anoop.pa@gmail.com>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1803/Tested-by: NShane McDonald <mcdonald.shane@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Loongson builds have an ad-hoc cmdline default of "console=ttyS0,115200
root=/dev/hda1". These settings come from a vendor; I remember builds
from Lemote branch requiring a "console=tty" override in order to get a
working console.

At least on Yeeloong, they're particularly useless: there's no external
serial port, and the IDE drive is now recognised as /dev/sda.
Signed-off-by: NRobert Millan <rmh@gnu.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1759/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The sysmips(MIPS_FIXADE, ...) case contains an obvious copy-and-paste
error in the handling of the TIF_LOGADE flag. Fix that

Patchwork: https://patchwork.linux-mips.org/patch/1997/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It was reported that GCC-4.3.3 (with CodeSourcery extensions) fails
without this.
Reported-by: NJonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2010/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

trace.func should be set to the recorded ip of the mcount calling site
in the __mcount_loc section to filter the function entries configured
through the tracing/set_graph_function interface, but before, this is
set to the self_ra(the return address of mcount), which has made
set_graph_function not work as expected.

This fixes it via calculating the right recorded ip in the __mcount_loc
section and assign it to trace.func.
Reported-by: NZhiping Zhong <xzhong86@163.com>
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2017/Signed-off-by: NRalf Baechle <ralf@duck.linux-mips.net>

This moves the comments out of ftrace_make_nop() and cleans it.  At the
same time, a macro MCOUNT_OFFSET_INSNS is defined for sharing with the
next patch.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2008/Signed-off-by: NRalf Baechle <ralf@duck.linux-mips.net>

The old prepare_ftrace_return() for MIPS is confused and have introduced
some problem. This patch cleans up the names of the arguments, variables
and related functions.

For MIPS, the 2nd argument of prepare_ftrace_return() is not really the
'selfpc' described in ftrace-design.txt but instead it is the self
return address. This did break the compatibility of the generic
interface but really reduced one unneeded calculation for to get the
current function name, the parent return address and the self return
address are enough, no need to tranform the self return address to the
self address.

But set_graph_function of function graph tracer is an exception, it does
need the 2nd argument of prepare_ftrace_return() as 'selfpc', for it
will use 'selfpc' to match user's configuration of function graph
entries, but in reality, it doesn't need the 'selfpc' but the recorded
ip address of the mcount calling site in the __mcount_loc section. So,
the 2nd argument of prepare_ftrace_return() is not important, the real
requirement is the right recorded ip address should be calculated and
assign to trace.func, this will be fixed in the next patches.
Reported-by: NZhiping Zhong <xzhong86@163.com>
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2007/Signed-off-by: NRalf Baechle <ralf@duck.linux-mips.net>

The old in_module() may not work in some situations(e.g. when module &
kernel are in the same address space when CONFIG_MAPPED_KERNEL=y), The
in_kernel_space() is more generic and it is also easy to be implemented
via cloning the existing core_kernel_text(), so, replace the in_module()
with in_kernel_space().
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2005/Signed-off-by: NRalf Baechle <ralf@duck.linux-mips.net>

This simply moves the "ip-=4" statement down to the end of the do { ...
} while (...); loop, which reduces one unneeded subtration and the
subsequent memory loading and comparison.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2006/Signed-off-by: NRalf Baechle <ralf@duck.linux-mips.net>

SPIN_LOCK_UNLOCK is deprecated. Use the lockdep capable variant instead.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2025/Signed-off-by: NRalf Baechle <ralf@duck.linux-mips.net>