when the AP is configured with HT40/2.4GHz and when PAPRD is enabled in station
we have PAPRD training frames never sent out because of the following
failure "PAPRD target power delta out of range". This consistently happens
in channel 10,11 in Over The Air testing and rarely in channel 6 under wired
setup.
        the reason behind this issue is all the HT40 rates target power
are 0 when we operate in channel 10/11 at 2.4GHz
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is the same fix as

   commit 84105160
   Author: Matteo Croce <technoboy85@gmail.com>
   Date:   Fri Dec 3 02:25:08 2010 +0100

   The ath9k driver subtracts 3 dBm to the txpower as with two radios the
   signal power is doubled.
   The resulting value is assigned in an u16 which overflows and makes
   the card work at full power.

in two more places. I grepped the ath tree and didn't find any others.

Cc: stable@kernel.org
Signed-off-by: NDaniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The Times They Are a-Changin'.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* enable LNA-diversity, fast-diversity for AR9485 based  on
  the value read from EEPROM content
* if antenna diversity/combining is supported, set LNA1 for the main
  antenna and LNA2 for the alternate antenna based on the new diversity
  algorithm

Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Cc: Luis Rodriguez <Luis.Rodriguez@Atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

XB113 (AR9380) 3x3 SB 5G only cards were failing to connect to APs
due to incorrect xpabiaslevel configuration. fix it.

Cc: stable@kernel.org
Cc: Ray Li <ray.li@greenwavereality.com>
Cc: Kathy Giori <kathy.giori@atheros.com>
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: compat@orbit-lab.org
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The XB113 cards are single band, 5 GHz-only, but the
default settings were configured to assume it was dual
band. Users of these cards then would see 2.4 GHz channels
but you would never get any scan results from these channels
given that the radio is not present.

Cc: stable@kernel.org
Cc: Fiona Cain <Fiona.Cain@atheros.com>
Cc: Ray Li <ray.li@greenwavereality.com>
Cc: Kathy Giori <kathy.giori@atheros.com>
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Dan Friedman <dan.friedman@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

- kenrel -> kernel
- whetehr -> whether
- ttt -> tt
- sss -> ss
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

With AR9003 at about ~ 10 feet from an AP that uses RTS / CTS you
will be able to associate but not not get data through given that
the power for the rates used was set too low. This increases the
power and permits data connectivity at longer distances from
access points when connected with HT40. Without this you will not
get any data through when associated to APs configured in HT40
at about more than 10 feet away.

Cc: stable@kernel.org
Cc: Fiona Cain <fcain@atheros.com>
Cc: Zhen Xie <Zhen.Xie@Atheros.com>
Cc: Kathy Giori <kathy.giori@atheros.com>
Cc: Neha Choksi <neha.choksi@atheros.com>
Cc: Wayne Daniel <wayne.daniel@atheros.com>
Cc: Gaurav Jauhar <gaurav.jauhar@atheros.com>
Cc: Samira Naraghi <samira.naraghi@atheros.com>
CC: Ashok Chennupati <ashok.chennupati@atheros.com>
Cc: Lance Zimmerman <lance.zimmerman@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

Change from the systems team to update PMU setting for AR9485
version of chipsets.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The size of the eeprom data is 1088 bytes for AR9485. But
a sanity check is done against 4K which would result in a
'potential read past the end of the buffer' smatch complaint.
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit 'ath9k_hw: Disable PAPRD for rates with low Tx power' changed
the code that sets the PAPRD rate masks to use only either the HT20 mask
or the HT40 mask. This is wrong, as the hardware can still use HT20 rates
even when configured for HT40, and the operating channel mode does not
affect PAPRD operation.
The register for the HT40 rate mask is applied as a mask on top of the
other registers to selectively disable PAPRD for specific rates on HT40
packets only.
This patch changes the code back to the old behavior which matches the
intended use of these registers. While with current cards this should not
make any practical difference (according to Atheros, the HT20 and HT40
mask should always be equal), it is more correct that way, and maybe
the HT40 mask will be used for some rare corner cases in the future.

Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Target Tx power available in eeprom is for PAPRD. If PAPRD
fails, paprd scale factor needs to be detected from this
target tx power.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the drop in Tx power for a particular mcs rate exceeds
the paprd scale factor, paprd may not work properly. Disable
paprd for any such rates.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The EEPROM contains scale factors for the tx power, which define
the range of allowable difference between target power and training
power. If the difference is too big, PA predistortion cannot be used.
For 2.4 GHz there is only one scale factor, for 5 GHz there are
three, depending on the specific frequency range.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9280 based hardware with 3 antennas and slow antenna diversity has
not been seen in the wild and ath9k does not support that form of
antenna diversity, so remove the EEPROM ops for it.
These EEPROM ops are currently only used for setting the
AR_PHY_SWITCH_COM register, which is being done in the EEPROM specific
file already.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR*_MAX_RATE_POWER => MAX_RATE_POWER
AR*_EEPROM_MODAL_SPURS => AR_EEPROM_MODAL_SPURS
AR*_OPFLAGS_* => AR5416_OPFLAGS_*
...
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Right now it is done for only AR9485, will be done for ar9003 also
after proper testing.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This helper function would be used for AR9485.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Calibration data are stored at 4k address (0xfff). The cal data
for AR9485 is not compressed so its lengh can exceed 1024 limit,
take care of that.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ar9300RateSize is not necessarily a power of 4.

Change ar9003_hw_set_target_power_eeprom
to print the targetPowerValT2 array one per line.

ath9k_hw_ar9300_set_txpower repeated the output 4 times per line,
change it to print the targetPowerValT2 value one per line.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove ath/debug.h and the includes of these files.
Coalesce long formats.
Correct a few misspellings and missing "\n"s from these logging messages.
Remove unnecessary trailing space before a newline.
Remove ARRAY_SIZE casts, use printf type %zu
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Parsing data using bitfields is messy, because it makes endian handling
much harder. AR9002 and earlier got it right, AR9003 got it wrong.
This might lead to either using too high or too low tx power values,
depending on frequency and eeprom settings.
Fix it by getting rid of the CTL related bitfields entirely and use
masks instead.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This feature is to mitigate the problem of certain 3
stream chips that exceed the PCIe power requirements.An EEPROM flag
controls which chips have APM enabled which is basically read from
miscellaneous configuration element of the EEPROM header.

This workaround will reduce power consumption by using 2 Tx chains for
Single and Double stream rates (5 GHz only).All self generated frames
(regardless of rate) are sent on 2 chains when this feature is
enabled(Chip Limitation).

Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Tested-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.

   text	   data	    bss	    dec	    hex	filename
  11161	     56	   2136	  13353	   3429	drivers/net/wireless/ath/ath9k/ar9003_paprd.o.new
  11167	     56	   2136	  13359	   342f	drivers/net/wireless/ath/ath9k/ar9003_paprd.o.old
  15428	     56	   3056	  18540	   486c	drivers/net/wireless/ath/ath9k/eeprom_4k.o.old
  15451	     56	   3056	  18563	   4883	drivers/net/wireless/ath/ath9k/eeprom_4k.o.new
  14087	     56	   2560	  16703	   413f	drivers/net/wireless/ath/ath9k/eeprom_9287.o.old
  14036	     56	   2560	  16652	   410c	drivers/net/wireless/ath/ath9k/eeprom_9287.o.new
  10041	     56	   2384	  12481	   30c1	drivers/net/wireless/ath/ath9k/ani.o.new
  10088	     56	   2384	  12528	   30f0	drivers/net/wireless/ath/ath9k/ani.o.old
   9316	   1580	   2304	  13200	   3390	drivers/net/wireless/ath/ath9k/htc_drv_init.o.new
   9316	   1580	   2304	  13200	   3390	drivers/net/wireless/ath/ath9k/htc_drv_init.o.old
  16483	     56	   3432	  19971	   4e03	drivers/net/wireless/ath/ath9k/ar9003_phy.o.new
  16517	     56	   3432	  20005	   4e25	drivers/net/wireless/ath/ath9k/ar9003_phy.o.old
  18221	    104	   2960	  21285	   5325	drivers/net/wireless/ath/ath9k/rc.o.old
  18203	    104	   2960	  21267	   5313	drivers/net/wireless/ath/ath9k/rc.o.new
  19985	     56	   4288	  24329	   5f09	drivers/net/wireless/ath/ath9k/eeprom_def.o.new
  20040	     56	   4288	  24384	   5f40	drivers/net/wireless/ath/ath9k/eeprom_def.o.old
  23997	     56	   4984	  29037	   716d	drivers/net/wireless/ath/ath9k/ar5008_phy.o.old
  23846	     56	   4984	  28886	   70d6	drivers/net/wireless/ath/ath9k/ar5008_phy.o.new
  24285	     56	   3184	  27525	   6b85	drivers/net/wireless/ath/ath9k/ar9003_eeprom.o.old
  24101	     56	   3184	  27341	   6acd	drivers/net/wireless/ath/ath9k/ar9003_eeprom.o.new
   6834	     56	   1032	   7922	   1ef2	drivers/net/wireless/ath/ath9k/ar9002_phy.o.old
   6780	     56	   1032	   7868	   1ebc	drivers/net/wireless/ath/ath9k/ar9002_phy.o.new
  36211	     64	   8624	  44899	   af63	drivers/net/wireless/ath/ath9k/hw.o.new
  36401	     64	   8624	  45089	   b021	drivers/net/wireless/ath/ath9k/hw.o.old
   9281	     56	   1496	  10833	   2a51	drivers/net/wireless/ath/ath9k/ar9003_calib.o.old
   9150	     56	   1496	  10702	   29ce	drivers/net/wireless/ath/ath9k/ar9003_calib.o.new

Use ARRAY_SIZE instead of a magic number.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Embedded boards do not have compressed EEPROM data, they use the
struct ar9003_eeprom layout, with little endian fields, so copying
the raw data to the eeprom buffer is enough.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some of the new AR9003 cards do not come with an external EEPROM chip
anymore. Calibration data on these cards is stored in the OTP ROM on
the chip.
This patch adds support for reading this data, and also adds support
for different EEPROM chip sizes (512 bytes instead of 1K).
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also round off interpolated values this would improve power
accuracy by 0.5dB in some cases.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>