SCM contains boot addr and boot mode registers to control
other processors on different OMAP versions. It controls the
boot address and mode for DSP based subsystems like: IVA 2.1
(OMAP2430), IVA 2.2 (OMAP3) and DSP (OMAP4).

If contained within SCM registers, when a processor is
booting it uses BOOTADDR to start running the code at that
location. BOOTMOD register specifies a different set of
modes for the processor to execute when booting (from direct,
idle, self-loop, user and default).

Since there was no offset associated with OMAP4, this patch
defines it.
Signed-off-by: NOmar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Define AM33XX control register, in order to allow access to
control register address space, also add CONTROL_SEC_CLK_CTRL
register offset; both are required in clock tree data,
for wdt0 and timer0 clock source select configuration.

CONTROL.SEC_CLK_CTRL register is provided to select/configure
clock input for WDT0 and TIMER0.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: added include of plat/am33xx.h to fix build break;
 added AM33XX_CONTROL_STATUS bitfields that will be needed for the clock
 tree; fixed some control.h whitespace problems while here]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Determine SoC type, i.e. whether GP or HS

Note: cpu_is_34xx() is true for am33xx also. Doing
cpu_is_am33xx() check after cpu_is_34xx() will not
achieve what we want due to the above reason.
Hence cpu_is_am33xx() is done before cpu_is_34xx()
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

There's no need to have these defines in plat/io.h.

Note that we now need to ifdef omap_read/write calls
as they will be available for omap1 only.

While at it, clean up the includes to group them like
they typically are grouped.
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch updates existing macros, functions used for TI816X, to enable
addition of other SoCs belonging to TI81XX family (e.g., TI814X).

The approach taken is to use TI81XX/ti81xx for code/data going to be common
across all TI81XX devices.

cpu_is_ti81xx() is introduced to handle code common across TI81XX devices.

In addition, ti8168_evm_map_io() is now replaced with ti81xx_map_io() and moved
in mach-omap2/common.c as same will be used for TI814X and is not board
specific.
Signed-off-by: NHemant Pedanekar <hemantp@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Upon return from off-mode, the ROM code jumps to a restore function
saved in the scratchpad.  Based on SoC revision or errata, this
restore entry point is different.  Current code uses some helper
functions in sleep34xx.S (get_*_restore_pointer) to get the restore
function entry point.

When returning from off-mode, this code is executed from SDRAM, so
there's no reason to use these helper functions when using the SDRAM
entry points directly would work just fine.

This patch uses ENTRY/ENDPROC to create "real" entry points for these
functions, and uses those values directly when writing the scratchpad.

Tested all three entry points
- restore_es3: 3430/n900
- restore_3630: 3630/Zoom3
- restore: 3530/Overo
Suggested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NJean Pihet <j-pihet@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

- kenrel -> kernel
- whetehr -> whether
- ttt -> tt
- sss -> ss
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch updates the common machine specific source files with support for
TI816X.
Signed-off-by: NHemant Pedanekar <hemantp@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP4 has three scalable voltage domains vdd_mpu, vdd_iva
and vdd_core. This patch adds the voltage tables and other
configurable voltage processor and voltage controller
settings to control these three scalable domains in OMAP4.
Signed-off-by: NThara Gopinath <thara@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds voltage driver support for OMAP3. The driver
allows  configuring the voltage controller and voltage
processors during init and exports APIs to enable/disable
voltage processors, scale voltage and reset voltage.
The driver maintains the global voltage table on a per
VDD basis which contains the various voltages supported by the
VDD along with per voltage dependent data like smartreflex
efuse offset, errminlimit and voltage processor errorgain.
The driver also allows the voltage parameters dependent on the
PMIC to be passed from the PMIC file through an API.
The driver allows scaling of VDD voltages either through
"vc bypass method" or through "vp forceupdate method" the
choice being configurable through the board file.

This patch contains code originally in linux omap pm branch
smartreflex driver.  Major contributors to this driver are
Lesly A M, Rajendra Nayak, Kalle Jokiniemi, Paul Walmsley,
Nishant Menon, Kevin Hilman. The separation of PMIC parameters
into a separate structure which can be populated from
the PMIC file is based on the work of Lun Chang from Motorola
in an internal tree.
Signed-off-by: NThara Gopinath <thara@ti.com>
[khilman: fixed link error for OMAP2-only defconfig]
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

OMAP3_IVA_MASK should use OMAP3_IVA_SHIFT instead of OMAP3_SGX_SHIFT
Signed-off-by: NArno Steffen <arno.steffen@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Move the padconf save code from pm34xx.c to the System Control Module
code in mach-omap2/control.c.  This is part of the general push to
move direct register access from middle-layer core code to low-level
core code, so the middle-layer code can be abstracted to work on
multiple platforms and cleaned up.

In the medium-to-long term, this code should be called by the mux
layer code, not the PM idle code.  This is because, according to the
TRM, saving the padconf only needs to be done when the padconf
changes[1].
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Tested-by: NRajendra Nayak <rnayak@ti.com>
Tested-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

1. OMAP34xx Multimedia Device Silicon Revision 3.1.x [Rev. ZH] [SWPU222H]
   Section 4.11.4 "Device Off-Mode Sequences"

Get rid of the open-coded scratchpad write in mach-omap2/prcm.c and
replace it with an actual API, omap3_ctrl_write_boot_mode().  While
there, get rid of the gratuitous omap_writel().

There's not much documentation available for what should wind up in
the scratchpad here, so more documentation would be appreciated.
Also, at some point, we should formalize our treatment of the scratchpad;
right now, accesses to the scratchpad are not well-documented.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Reviewed-by: NKevin Hilman <khilman@deeprootsystems.com>
Tested-by: NKevin Hilman <khilman@deeprootsystems.com>
Tested-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

Using macros from existing include files for registers addresses.

Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.

Based on original patch from Vishwa.
Signed-off-by: NJean Pihet <j-pihet@ti.com>
Cc: Vishwanath BS <vishwanath.bs@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Erratum id: i608
RTA (Retention Till Access) feature is not supported and leads to device
stability issues when enabled. This impacts modules with embedded memories
on OMAP3630

Workaround is to disable RTA on boot and coming out of core off.
For disabling RTA coming out of off mode, we do this by overriding the
restore pointer for 3630 as the first point of entry before caches are
touched and is common for GP and HS devices. To disable earlier than
this could be possible by modifying the PPA for HS devices, but not for
GP devices.

Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: NJean Pihet <j-pihet@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

[ambresh@ti.com: co-developer]
Signed-off-by: NAmbresh K <ambresh@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Only OMAP2+ platforms have the System Control Module (SCM) IP block.
In the past, we've kept the SCM header file in plat-omap.  This has
led to abuse - device drivers including it; includes being added that
create implicit dependencies on OMAP2+ builds; etc.

In response, move the SCM headers into mach-omap2/.

As part of this, remove the direct SCM access from the OMAP UDC
driver.  It was clearly broken.  The UDC code needs an indepth review for
use on OMAP2+ chips.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>

The OMAP ASoC McBSP code implemented CLKR and FSR signal muxing via
direct System Control Module writes on OMAP2+.  This required the
omap_ctrl_{read,write}l() functions to be exported, which is against
policy: the only code that should call those functions directly is
OMAP core code, not device drivers.  omap_ctrl_{read,write}*() are no
longer exported, so the driver no longer builds as a module.

Fix the pinmuxing part of the problem by removing calls to
omap_ctrl_{read,write}l() from the OMAP ASoC McBSP code and
implementing signal muxing functions in arch/arm/mach-omap2/mcbsp.c.
Due to the unfortunate way that McBSP support is implemented in ASoC
and the OMAP tree, these symbols must be exported for use by
sound/soc/omap/omap-mcbsp.c.

Going forward, the McBSP device driver should be moved from
arch/arm/*omap* into drivers/ or sound/soc/*, and the CPU DAI driver
should be implemented as a platform_driver as many other ASoC CPU DAI
drivers are.  These two steps should resolve many of the layering
problems, which will rapidly reappear during a McBSP hwmod/PM runtime
conversion.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Acked-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch has multiple fixes together. To ensure that git bisect work across
commits, all changes are clubbed together

1. Move the common control base address to control core
2. Remove the manually coeded defines and use the ones from headers.
3. Fix the the status register define in id.c for OMAP4
4. Fix all the register define in hsmmc.c
5. Use the control pad accessor API for omap4 hsmmc register accesses
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

On OMAP4, control module is divided into 4 separate IPs
- OMAP44XX_CTRL_MODULE_CORE
- OMAP44XX_CTRL_MODULE_PAD_CORE
- OMAP44XX_CTRL_MODULE_WKUP
- OMAP44XX_CTRL_MODULE_PAD_WKUP

This patch adds all the omap4 control module register data and
includes them in the common control.h

The register data is autogenerated from the codebase thanks
to Benoit Cousson efforts
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

On OMAP4 control pad are not addressable from control
core base. So the common omap_ctrl_read/write APIs breaks
Hence export separate APIs to manage the omap4 pad control
registers.

This APIs will work only for OMAP4
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

In OMAP4, MMC1 PBIAS and its associated IO is software-controlled
by CONTROL_PBIAS and CONTROL_MMC1 registers. This patch adds PBIAS
configuration for MMC1 Controller during power-ON and power-OFF
of regulator.
Signed-off-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes the omap_type function to detect whether the device
is GP or HS
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: NKevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

AM3517/05 has few additional control module registers to control
the new IP's, like VPFE, USBOTG, CPGMAC.

This patch adds the bit defination for INTR_CLR and SW_RST control
register.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

omap: Replace orred CONFIG_ARCH_OMAP2/3/4 with CONFIG_ARCH_OMAP2PLUS
Signed-off-by: NTony Lindgren <tony@atomide.com>

AM3517/05 has a few additional control module registers defined mainly
to control the new IP's. This patch adds support for those new registers.
Signed-off-by: NRanjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

not(!) has a higher precedence than bit and(&).
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The speed ctrl bit for MMC I/O is part of CONTROL_PROG_IO1 register
in omap3630.This patch sets it up accordingly.
Signed-off-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The OMAP35x family has multiple variants differing
in the HW features. This patch detects these features
at runtime and prints information during the boot.

Since most of the code seemed repetitive, macros
have been used for readability.
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Errata: ES3.0, ES3.1 SDRC not sending auto-refresh when OMAP wakes-up
from OFF mode
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Signed-off-by: NKalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Add context save and restore for the System Control Module to suport
off-mode.

ETK and debobs definitions added by Peter De Schrijver.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NPeter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch populates the scratchpad contents as expected by the
bootROM code.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Add context save and restore for PRCM module to support off-mode.
Additional registers (CM_CLKSEL4, CM_CLKEN, CM_CLKEN2) added by Tero
Kristo.

Missing CM_CLKEN_PLL_IVA2 register added by Kalle Jokiniemi.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Signed-off-by: NKalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.

This was done with:

#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"

for header in $headers; do
	old="#include <mach\/$header"
	new="#include <plat\/$header"
	for dir in $omap_dirs; do
		find $dir -type f -name \*.[chS] | \
			xargs sed -i "s/$old/$new/"
	done
	find drivers/ -type f -name \*omap*.[chS] | \
		xargs sed -i "s/$old/$new/"
	for file in $other_files; do
		sed -i "s/$old/$new/" $file
	done
done

for header in $(ls $mach_dir_old/*.h); do
	git mv $header $plat_dir_new/
done
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch splits OMAP2_IO_ADDRESS to OMAP2_L3_IO_ADDRESS and
OMAP2_L4_IO_ADDRESS to reclaim more IO space.

The omap_read*() and omap_write*() functions will work only over
L4 address space. Current omap kernel stack uses these functions
only to access registers over L4 io address space

Note that these macros should only be used when ioremap does
not work. Please use ioremap instead in all new code.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Search and replace OMAP_IO_ADDRESS with OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS,
and convert omap_read/write into a functions instead of a macros.

Also rename OMAP_MPUIO_VBASE to OMAP1_MPUIO_VBASE.

In the long run, most code should use ioremap + __raw_read/write instead.
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds the support for OMAP4. The platform and machine specific
headers and sources updated for OMAP4430 SDP platform.

OMAP4430 is Texas Instrument's SOC based on ARM Cortex-A9 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add D2D clocks (modem_fck, sad2d_ick, mad2d_ick) to clock framework
and ensure that auto-idle bits are set for these clocks during PRCM
init.

Also add omap3_d2d_idle() function called durint PRCM setup which
ensures D2D pins are MUX'd correctly to enable retention for
standalone (no-modem) devices.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Add low-level initialization for hsmmc controller. Merged into
this patch patch are various improvments and board support by
Grazvydas Ignotas and David Brownell.

Also change wire4 to be wires, as some newer controllers support
8 data lines.

Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>