Patch from Lennert Buytenhek

Analogous to the previous patch that allows ioremap() to use section
mappings, this patch allows ioremap() to use supersection mappings.
Original patch by Deepak Saxena.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Allow section mappings to be setup using ioremap() and torn down
with iounmap().  This requires additional support in the MM
context switch to ensure that mappings are properly synchronised
when mapped in.

Based an original implementation by Deepak Saxena, reworked and
ARMv6 support added by rmk.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On some CPUs, bit 4 of section mappings means "update the
cache when written to".  On others, this bit is required to
be one, and others it's required to be zero.  Finally, on
ARMv6 and above, setting it turns on "no execute" and prevents
speculative prefetches.

With all these combinations, no one value fits all CPUs, so we
have to pick a value depending on the CPU type, and the area
we're mapping.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This prepares the way for adding support for the new Atmel AT91SAM926x
processors.

Major changes:
- Rename time.c to at91rm9200_time.c
- Rename common.c to at91rm9200.c
- Introduce ARCH_AT91, of which ARCH_AT91RM9200, ARCH_AT91SAM9260 and
ARCH_AT91SAM9261 are dependent.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Most MMU-based CPUs have a restriction on the setting of the data cache
enable and mmu enable bits in the control register, whereby if the data
cache is enabled, the MMU must also be enabled.  Enabling the data
cache without the MMU is an invalid combination.

However, there are CPUs where the data cache can be enabled without the
MMU.

In order to allow these CPUs to take advantage of that, provide a
method whereby each proc-*.S file defines the control regsiter value
for use with nommu (with the MMU disabled.)  Later on, when we add
support for enabling the MMU on these devices, we can adjust the
"crval" macro to also enable the data cache for nommu.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The "id(wb)BRR" suffix reports which CPU debugging options were (or
were not) selected at kernel build time.  Rather than have every
proc-*.S file implement this, report the control register value,
from which this information can be deduced.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

In noMMU mode, various of functions which are defined in mm/proc-*.S
is not valid or needed to be avoided. i.g. switch_mm is not needed,
just returns and this makes the I & D caches are valid which shows
great improvement of performance including task switching and IPC.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This is a trivial patch to export flush_dcache_page in mm/nommu.c.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove fault-armv.o, mmap.o and mm-armv.o from uclinux builds - these
are concerned with MMU-ful operations, and as such are redundant for
uclinux.

Since this also removes iotable_init() and iotable_init() is used
extensively in the platform support files, just make it a no-op.

Based upon a couple of patches by Hyok.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

TABLE_SIZE is never used in arch/arm/mm/init.c.  create_memmap_holes(),
memtable_init, and setup_io_desc() no longer exist in the kernel.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

nommu doesn't require a complex flush_dcache_page implementation
like the MMU-ful CPUs do, so provide a simplified version in nommu.c
and omit flush.c from the build as appropriate.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

nommu doesn't have any form of remapping support, so ioremap, etc
become stubs which just return the casted address, doing nothing
else.

Move ioport_map(), ioport_unmap(), pci_iomap(), pci_iounmap()
into a separate file which is always built.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Since uclinux doesn't make use of the TLB, including the TLB
maintainence and CPU-optimised copypage functions does not
make sense.  Remove them.

(This is part of one of Hyok's patches.)
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Since there can be no fixed location for the TLS value with nommu
systems, we must provide TLS register emulation in order to support
TLS binaries on CPUs without the thread register.

Part of a patch from Hyok S. Choi, and cleaned up by rmk.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

proc-v6 contains some compatibility to be able to use the V6
"cps" instruction.  However, the kernel makes use of this
instruction elsewhere extensively, so there's no point keeping
this compatibility anymore.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As for RETINSTR, LOADREGS is a left-over from the 26-bit days.
Remove it.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Select CONFIG_CPU_ARM926 when CONFIG_CPU_S3C2412 is
selected.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Sascha Hauer

This patch adds the base support for Hilscher's netX network
processors.
Signed-off-by: NRobert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Vitaly Wool

This patch adds basic chip support for PNX4008 ARM platform.
It's basically the same as the previous one, but with the rmk's
comments taken into account.
Signed-off-by: NVitaly Wool <vwool@ru.mvista.com>
Signed-off-by: NDmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The ARM Architecture Reference Manual lists bit 4 of the PMD as "implementation
defined" and it must be set to zero on Intel XScale CPUs or the cache does
not behave properly. Found by Mike Rapoport while debugging a flash issue
on the PXA255:

	http://marc.10east.com/?l=linux-arm-kernel&m=114845287600782&w=1Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

We don't enable the BTB on the ixp2350 as that can cause weird
crashes (erratum #42.)  However, some bootloaders enable the BTB,
which means that we have to disable the BTB explicitly.

Found thanks to Tom Rini.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Patch from Catalin Marinas

This patch modifies the __ioremap_pfn and __iounmap functions in
arch/arm/mm/ioremap.c to use vunmap instead of vfree.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

We had two implementations for flushing the cache, which meant StrongARM
caches weren't being correctly flushed.  Fix this by always using the
v4wb_flush_kern_cache_all method, rather than duplicating it.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

FLUSH_BASE must be visible to arch/arm/mm/init.c in order for the
memory region to be setup.  Move these definitions from
asm-arm/arch-*/hardware.h into asm-arm/arch-*/memory.h where mm
stuff can see them.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

This patch adds support for the I/O coherent cache available on the
xsc3.  The approach is to provide a simple API to determine whether the
chipset supports coherency by calling arch_is_coherent() and then
setting the appropriate system memory PTE and PMD bits.  In addition,
we call this API on dma_alloc_coherent() and dma_map_single() calls.
A generic version exists that will compile out all the coherency-related
code that is not needed on the majority of ARM systems.

Note that we do not check for coherency in the dma_alloc_writecombine()
function as that still requires a special PTE setting.  We also don't
touch dma_mmap_coherent() as that is a special ARM-only API that is by
definition only used on non-coherent system.
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

Adapt xsc3 to the changes in 74945c86
(xsc3 was written before but merged after the latter went in.)
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

This patch adds support for the new XScale v3 core.  This is an
ARMv5 ISA core with the following additions:

- L2 cache
- I/O coherency support (on select chipsets)
- Low-Locality Reference cache attributes (replaces mini-cache)
- Supersections (v6 compatible)
- 36-bit addressing (v6 compatible)
- Single instruction cache line clean/invalidate
- LRU cache replacement (vs round-robin)

I attempted to merge the XSC3 support into proc-xscale.S, but XSC3
cores have separate errata and have to handle things like L2, so it
is simpler to keep it separate.

L2 cache support is currently a build option because the L2 enable
bit must be set before we enable the MMU and there is no easy way to
capture command line parameters at this point.

There are still optimizations that can be done such as using LLR for
copypage (in theory using the exisiting mini-cache code) but those
can be addressed down the road.
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Mark page table walks with outer-cacheable attribute, and enable no-execute
in page tables.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

set_page_count usage outside mm/ is limited to setting the refcount to 1.
Remove set_page_count from outside mm/, and replace those users with
init_page_count() and set_page_refcounted().

This allows more debug checking, and tighter control on how code is allowed
to play around with page->_count.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Have an explicit mm call to split higher order pages into individual pages.
 Should help to avoid bugs and be more explicit about the code's intention.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Patch from Lennert Buytenhek

This patch adds support for the Cirrus ep93xx series of CPUs.  The
ep93xx is an ARM920T based CPU with two VICs, PL010 based UARTs,
IrDA, MaverickCrunch floating point coprocessor, between 24 and 64
GPIOs, ethernet, OHCI USB and, depending on the model, pcmcia, raster
engine, graphics accelerator, IDE controller and a bunch of other
stuff.

This patch adds the core ep93xx support code, and support for the
Glomation GESBC-9312-sx and the Technologic Systems TS-72xx SBCs.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

asm/hardware.h is not required for the majority of processor support
files, ioremap support, mm initialisation, acorn IO support, nor
the debug code (which picks up its machine specific includes via
debug-macros.S)
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rather than having a growing dependency line, use select to set
these configuration symbols.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Move the hardware PMD and PTE page table definitions from pgtable.h
into pgtable-hwdef.h, and include pgtable-hwdef.h as necessary.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Catalin Marinas

ARM1136 erratum 371025 (category 2) specifies that, under rare
conditions, an invalidate I-cache by MVA (line or range) operation can
fail to invalidate a cache line. The recommended workaround is to
either invalidate the entire I-cache or invalidate the range by
set/way rather than MVA.

Note that for a 16K cache size, invalidating a 4K page by set/way is
equivalent to invalidating the entire I-cache.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Catalin Marinas

Chapter B2.7.3 in the latest ARM ARM (with v6 information) states that
the completion of a TLB maintenance operation is only guaranteed by
the execution of a DSB (Data Syncronization Barrier, formerly Data
Write Barrier or Drain Write Buffer).

Note that a DSB is only needed in the flush_tlb_kernel_* functions
since the completion is guaranteed by a mode change (i.e. switching
back to user mode) for the flush_tlb_user_* functions.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

CONFIG_CPU_MPCORE has never been a configuration symbol - it should
be CONFIG_CPU_32v6K.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

Doing so adds a much larger cost to the loop than the cost implied by
simply invalidating the whole BTB at once.
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

The mini I-cache issue is valid only for kernel space since debuggers
would not fly if they used user space addresses for their stubs.
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from George G. Davis

This Freescale Semiconductor, Inc. contributed patch adds mem_types[]
support for ARMv6 non-shared device memory region attributes. This
implementation provides support for only first level section mapped
non-shared devices. Second level non-shared device mappings are not
yet supported.
Signed-off-by: NGeorge G. Davis <gdavis@mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>