The displays (connectors, panels and encoders) bail out from their
.enable() and .disable() handlers if the dss device is already enabled
or disabled. Those safety checks are not needed when the functions are
called through the omapdss_device_ops, as the .enable() and .disable()
handlers are called from the DRM atomic helpers that already guarantee
that no double enabling or disabling can occur.

However, the handlers are also called directly from the .remove()
handler. While this shouldn't be needed either as the modules can't be
removed as long as the device is in use, it's still a good practice to
disable the device explicitly. There is currently a safety check in
.remove() in some drivers but not all of them.

Remove the safety checks from the .enable() and .disable() handlers, and
add missing ones in the .remove() handler.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: NSebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

All .enable() and .disable() handlers for panels and connectors share
common code that validates and updates the device's state. Move it to
common locations in the omap_encoder_enable() and omap_encoder_disable()
handlers.

The enabled check in the .disable() handler is left untouched, it will
be addressed separately.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: NSebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Instead of calling the .set_timings() operation recursively from the
display device backwards, iterate over the devices manually in the DRM
encoder code. This moves the complexity to a single central location and
simplifies the logic in omap_dss_device drivers.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Panels drivers store their timings in a device data structure field that
is initialized at probe time, either from hardcoded values or from
firmware-supplied values. Those timings are then reported through the
.get_timings() operation to construct the panel display mode.

The panel timings are further modified by the .set_timings() operation,
which is called with the timings retrieved by .get_timings(), and
mangled by .check_timings(). The latter potentially adjusts the pixel
clock only.

Conceptually, modifying the panel timings is wrong, as the timings are
an intrinsic property of the panel and should thus be fixed.
Furthermore, modifying them this way at runtime can result in display
modes reported to userspace varying between calls, which is also wrong.

There's no actual need to store the mangled pixel clock value in the
timings. Don't modify the panel timings in the .set_timings() operation,
just forward it to the previous device in the display pipeline.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The .check_timings() operation is called recursively from the display
device back to the output device. Most components just forward the
operation to the previous component in the chain, resulting in lots of
duplicated pass-through functions. To avoid that, iterate over the
components manually.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Source components in the display pipeline need to configure their output
signals polarities and clock driving edge based on the requirements of
the sink component.

Those requirements are currently shared across the whole pipeline in the
flags of a videomode structure, instead of being local to each bus. This
both prevents multiple buses from having different configurations (when
the hardware supports it), and makes it difficult to move from videomode
to drm_display_mode as the latter doesn't contain bus polarities and
clock edge flags.

Add a bus_flags field to the omap_dss_device structure and move the
DISPLAY_FLAGS_DE_(LOW|HIGH), DISPLAY_FLAGS_PIXDATA_(POS|NEG)EDGE and
DISPLAY_FLAGS_SYNC_(POS|NEG)EDGE videomode flags to bus_flags in all
external encoders, connectors and panels. The videomode flags are still
used internally for internal encoders, this will be addressed in a
second step.

The related videomode flags in the default mode of the DVI connector can
simply be dropped, as they are always overridden by the TFP410 driver.
Note that this results in both the DISPLAY_FLAGS_SYNC_POSEDGE and
DISPLAY_FLAGS_SYNC_NEGEDGE flags being set, which is invalid, but only
the former is tested for when programming the DISPC, so the DVI
connector flags are effectively overridden by the TFP410 flags.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The omap_dss_device .set_timings() operations are called directly from
omap_encoder_update(), and indirectly from the omap_dss_device .enable()
operation. The latter is called from omap_encoder_enable(), right after
calling omap_encoder_update(). The .set_timings() operation it thus
called twice in a row. Fix it by removing the indirect call.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The .set_timings() operations of the omap_dss_device instances don't
need to modify the passed timings. Make the pointer const.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

omap_dss_device instances have two ops structures, omap_dss_driver and
omap_dss_device_ops. The former is used for devices at the end of the
pipeline (a.k.a. display devices), and the latter for intermediate
devices.

Having two sets of operations isn't convenient as code that iterates
over omap_dss_device instances need to take them both into account.
There's currently a reasonably small amount of such code, but more will
be introduced to move the driver away from recursive operations. To
simplify current and future code, move all operations that are not
specific to the display device to the omap_dss_device_ops.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The GPIO descriptor API is favoured over the plain GPIO API for consumer
drivers. Using it simplifies the driver code.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The omapdrm and omapdss drivers are architectured based on display
pipelines made of multiple components handled from sink (display) to
source (DSS output). This is incompatible with the DRM bridge and panel
APIs that handle components from source to sink.

To reconcile the omapdrm and omapdss drivers with the DRM bridge and
panel model, we need to reverse the direction of the DSS device
operations. Start with the connect and disconnect operations.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The omapdss_of_find_source_for_first_ep() function locates the source
corresponding to the first endpoint of the first port of a device node.
We can easily extend it to locate sinks as well by passing the port
number as a parameter. This will be useful to find sinks in encoders
drivers.

Extend the function and rename it to omapdss_of_find_connected_device()
to reflect its new extended purpose.

Additionally, it is useful to differentiate between failures to return
the connected device because no link exists in the device tree for the
requested port, or because the connected device as described in the
device tree is invalid or not probed yet. Return NULL in the first case
and an error code in the second case, and update the callers
accordingly.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The omap_dss_device port_num field stores the DT port number associated
with the device. The field is used in different ways depending on the
device type:

- For DPI outputs, the port number is used as an identifier of the DPI
instance

- For sources, the port number is used to look up the omap_dss_device by
DT port node

As omap_dss_device instances are only looked up as sources by sinks,
setting the field to the number of the source port works for both use
cases.

However, to enable looking up sinks, we need to record all the ports
associated with an omap_dss_device. Do so by turning the port_num field
into an of_ports bitmask. For DPI outputs the port number is
additionally stored in the dpi_data structure as the output ID.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Storing the dss_device pointer in the omap_dss_device structure will
allow accessing the dss_device from the dss_mgr API functions.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The functions operate on any omap_dss_device, move them from display.c
to base.c. While at it rename them to match the naming of the other
functions operating on struct omap_dss_device.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The panel devices list isn't used anymore, all panel devices are
accessed through the global devices list. Remove it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Split the function into omapdss_display_init() to perform
display-specific initialization of the omap_dss_device, and
omapdss_register_display() to register the device. The latter will then
be replaced by more generic registration.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

All connectors, encoders and panels store a pointer to their input
omap_dss_device in the panel driver data structure. This duplicates the
src field in the omap_dss_device structure. Remove the private copy and
use the src field.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation for the move of checks from the disconnect handlers to
the omapdss_device_disconnect() function, replace direct calls to the
disconnect handlers at remove time with calls to
omapdss_device_disconnect().
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The connectors, encoders and display duplicate the same debug messages
and connection checks in their omap_dss_device connect and disconnect
handlers. Move the code to the connect and disconnect wrappers.

To simplify the code the connect function returns -EBUSY unconditionally
if the device is already connected. This doesn't cause any change in
practice: the connect handler of displays is never called on a connected
device as it is only invoked during omapdrm initialization.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The omap_dss_device objects model display components and are connected
at runtime to create display pipelines. The connect and disconnect
operations implemented by each component contain lots of duplicate code.
As a first step towards fixing this, create new functions to wrap the
direct calls to those operations and use them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The various types of omapdss_*_ops structures define multiple operations
that are not specific to a bus type. To simplify the code and remove
dependencies on specific bus types move those operations to a common
structure. Operations that are specific to a bus type are kept in the
specialized ops structures.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The omap_dss_device structure stores a videomode. All the connector and
panel drivers that use omap_dss_device also store the videomode in their
own panel_drv_data structures. There's no need to duplicate, remove the
videomode field from omap_dss_device.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The structure contains function pointers that don't need to be modified.
Make all its instances const to improve security.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Change tomi.valkeinen@nokia.com to tomi.valkeinen@ti.com.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Fix sparse warning:

drivers/gpu/drm/omapdrm/displays/panel-sony-acx565akm.c:224:23: warning: cast to restricted __be32
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The connector drivers need a handle to the source they are connected to
in order to control the source.

All drivers get that handle at probe time, resulting in probe deferral
when the source hasn't been probed yet. However they don't need the
handle until their connect handler is called.

Move retrieval of the source handle to the connect handler to avoid
probe deferrals.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

No panel is instantiated through platform data anymore, there is no
need to check for OF node presence.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The kernel favours 'unsigned int' over plain 'unsigned'. Replace all
occurences of the latter by the former. This avoid lots of checkpatch
complaints in patches that touch lines where a plain 'unsigned' is used.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

As non-DT booting is no longer supported, the only way to instantiate
the device is through an OF node, which is guaranteed to be present.
Remove the unneeded check.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.

File size before:
   text	   data	    bss	    dec	    hex	filename
   5147	    560	      0	   5707	   164b	panel-sony-acx565akm.o

File size After adding 'const':
   text	   data	    bss	    dec	    hex	filename
   5211	    496	      0	   5707	   164b	panel-sony-acx565akm.o
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

get_resolution is not used, remove it.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Non-DT booting is no longer supported, so remove legacy code.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Add module alias for Sony ACX565AKM LCD panel. This makes it probe on Nokia
N900 when panel driver is built as a module.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use 'vm' to refer to a struct videomode instead of 'p', 't', 'timings' or
something else.

The code will be easier to follow if we use consistent names.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

omap_video_timings can be replaced with the generic videomode in omapdrm
and the omap_video_timings can be removed.

This patch will replace the omap_video_timings with videomode.
With the change we no longer need the functions to convert to/from
videomode and drm_display_mode to omap_video_timings, these can be removed
as well.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for sync edge.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for pixel data edge.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for DE level.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for h/vsync level.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>