In order to maximize the use of MSI, a PCIe controller will share
all MSI controllers. The patch changes msi-parent to refer to all
MSI controller dts nodes.
Signed-off-by: NMinghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

"1" should be replaced by "l". This is a typo.
The patch is to fix it.
Signed-off-by: NMinghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

AT91SAM9G45 has an AC97 controller, but it is not described in the dts
file.
This patch adds AC97 node in device tree.
Signed-off-by: NDmitry Rezvanov <dmitry.rezvanov@yandex.ru>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add pinctrl groups of ethenet phy mode, such as "ether_rgmii", "ether_rmii",
and "ether_mii".
Signed-off-by: NKunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

All registers are located within 0x400 size from the base address.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

Add UniPhier AIDET (ARM Interrupt Detector) nodes to support
active low interrupts.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

Since the discussion is not settled yet for the EMAC, and that the release
in getting really close, let's revert the changes for now, and we'll
reintroduce them later.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This reverts commit ddb56254. The EMAC
bindings have not stabilized yet, so we can't commit to keeping them
stable.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This patch solves the following error:
arch/arm/boot/dts/rk3228-evb.dtb: ERROR (phandle_references): Reference to non-existent node or label "phy0"

Fixess db40f15b ("ARM: dts: rk3228-evb: Enable the integrated PHY for gmac")
Signed-off-by: NDavid Wu <david.wu@rock-chips.com>
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the as3645a flash controller to the DT source.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

CEC support was added for Exynos5 in 4.13, but for the Odroids we need to set
'needs-hpd' as well since CEC is disabled when there is no HDMI hotplug signal,
just as for the exynos4 Odroid-U3.

This is due to the level-shifter that is disabled when there is no HPD, thus
blocking the CEC signal as well. Same close-but-no-cigar board design as the
Odroid-U3.

Tested with my Odroid XU4.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Rockchip's rv1108-evb board has one usb otg controller and one usb
host controller, each usb controller connect with one usb-phy port
through UTMI+ interface. This patch enables them to support usb on
rv1108-evb board.
Signed-off-by: NFrank Wang <frank.wang@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

This patch adds usb otg/host controllers and phys nodes for RV1108 SoCs.
Signed-off-by: NFrank Wang <frank.wang@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

The window of the Aspeed AST2400 SMC Controllers to map chips on the
AHB Bus has a 256MB size. The full window range is

    [ 0x20000000 - 0x2FFFFFFF ] for the FMC controller
    [ 0x30000000 - 0x3FFFFFFF ] for the SPI controller

This change requires CONFIG_VMSPLIT_2G to be set.
Signed-off-by: NCédric Le Goater <clg@kaod.org>
Signed-off-by: NJoel Stanley <joel@jms.id.au>

The cpu is powered by regulator vdd_core on RV1108 evalution
board. Add it to the cpu dt node.
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Add cpu opp table for rv1108 to support frequency
from 408MHZ to 1008MHZ.
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

This adds the operating points to the Ux500 device tree and
deletes the old special-purpose cpufreq node, as we can now
use the generic DT cpufreq driver.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Add VPU/VDEC/VOP/IEP iommu nodes
Signed-off-by: NSimon Xue <xxm@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Earlyconsole is used for early kernel debugging that's why this option
shouldn't be enabled by default.
Earlyconsole is partially copying the part of the bootlog after
"bootconsole [uart0] disabled".
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Change the dtsi include code to use the C pre-processor #include instead
of the device tree /include/. This brings all Zynq device trees inline
with each other.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This will simplify dt overlay structure for the whole PL.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Mention device-type = "ethernet-phy", as qemu will need this in absence
of compatible.
Signed-off-by: NSai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Describe adv7511 on i2c bus.
Signed-off-by: NChristian Kohn <christian.kohn@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This adds a new node for the LEGO MINDSTORMS EV3 LCD display.
Signed-off-by: NDavid Lechner <david@lechnology.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Add dt node of bosch accelerometer bma250e on rv1108 evb.
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

RK805 is used as the voltage regulator on rv1108 evaluation
board. Add device tree node for it.
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

The BPI-M3 is an Allwinner A83T based SBC in the Bananapi/Bpi family.
It is roughly the same form factor as the BPI-M1+, with roughly the
same peripherals and connectors:

  - 2GB LPDDR3 DRAM
  - 8GB eMMC
  - Micro-SD card slot
  - HDMI output
  - Headset (stereo + mic) jack
  - Onboard mic
  - Gigabit Ethernet with RTL8211E transceiver
  - Ampak AP6212 WiFi + BT
  - USB OTG connector
  - USB-to-SATA bridge connected through a USB 2.0 hub
  - Consumer IR receiver
  - MIPI DSI LCD panel connector
  - Camera interface (parallel and MIPI CSI) connector
  - 3 LEDs (Red, Green, Blue), of which 2 are controllable (GB)
  - Raspberry Pi 2 compatible GPIO header
Signed-off-by: NChen-Yu Tsai <wens@csie.org>

RV1108 EVB uses pwm0 modulate the backlight, add dt
node to enable it.
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Add pwm device tree node for rv1108 soc
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

dtc recently added PCI bus checks. Fix these warnings.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

dtc recently added PCI bus checks. Fix these warnings.
Signed-off-by: NRob Herring <robh@kernel.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The h8homlet board has the A83T's standard USB 1.1/2.0 host pair routed
to a USB host port on the board. The other USB host port is routed to
USB OTG controller.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>

The Cubietruck-plus has a GL830 USB-to-SATA bridge connected to EHCI0,
and a USB3503 HSIC USB 2.0 hub connected to EHCI1. The USB3503's I2C
control interface is not connected.

This patch enables both EHCI controllers, adds a device node for the
USB hub, and includes sunxi-common-regulators.dtsi for the VBUS
regulators. The existing reg_vcc3v3 is dropped as it is also available
in the set of common regulators. Other unused regulators are disabled.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>

The USB OTG controller found on the A83T is compatible with the one
found on the A33.

Add a device node for it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>

The A83T has 3 USB PHYs, 1 for USB OTG, 1 for standard USB 2.0, 1 for
USB HSIC. EHCI0/OHCI0 are the standard USB host pair, while EHCI1 is
the host controller for HSIC. OTG is not added yet.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Tested-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Previous value was a bad copy of nitrogen6_max device tree.
Signed-off-by: NGary Bisson <gary.bisson@boundarydevices.com>
Fixes: 3faa1bb2 ("ARM: dts: imx: add Boundary Devices Nitrogen6_SOM2 support")
Cc: <stable@vger.kernel.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This uses trigger-sources documented in commit 80dc6e1c ("dt-bindings:
leds: document new trigger-sources property") to specify USB ports. Such an
information can be used by operating system to setup LEDs behavior.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add dt nodes for generic-ehci/ohci host controller.
Signed-off-by: NRaveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Signed-off-by: NScott Branden <scott.branden@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Use serial0 alias to select stdout-path on Cygnus bcm911360_entphon
board.
Signed-off-by: NScott Branden <scott.branden@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add nodes for peripherals in Cygnus dtsi: sdhci, keypad, spi, dma,
pinmux configs.
Signed-off-by: NJonathan Richardson <jonathan.richardson@broadcom.com>
Signed-off-by: NScott Branden <scott.branden@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>