- 06 8月, 2009 18 次提交
-
-
由 Benjamin LaHaise 提交于
This patch prefetches RxD descriptors which helps to lower the latency of a cache miss in vxge_hw_ring_rxd_next_completed. This lowers the % of CPU time used by vxge_hw_ring_rxd_next_completed() where the descriptor is accessed in profiling netperf on a P4 Xeon from 1.5% to 1.0%. Signed-off-by: NBenjamin LaHaise <ben.lahaise@neterion.com> Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin LaHaise 提交于
wmb() is extremely heavy on x86. The semantics required in the driver are provided by mmiowb(), so use that and improve tx performance on P4 Xeons by 5-10%. Signed-off-by: NBenjamin LaHaise <ben.lahaise@neterion.com> Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin LaHaise 提交于
This patch fixes a case in the transmit completion code which was resulting in pktgen hanging at the end of a run. The cause is due to the fact that the ->cb[] area of an skb cannot be used in a network driver's transmit path, as that area belongs to the network protocol. Pktgen hangs, as it sends out the same packet multiple times, and vxge's use of this area of the skb for a temporary list can only add the packet to the temporary list once (while it may be on the queue many times). The fix is to remove this abuse of skb->cb[]. Instead, skb pointers are placed into a temporary stack array, and then free outside of the tx lock. This retains the smp optimization of doing dev_kfree_skb() outside of the tx lock. Signed-off-by: NBenjamin LaHaise <ben.lahaise@neterion.com> Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benjamin LaHaise 提交于
The vxge driver will drop a packet in its transmit function if the number of TxDs available hits 0. Instead of doing that, simply stop the transmit queue when transmitting a packet with the last available TxD. Signed-off-by: NBenjamin LaHaise <ben.lahaise@neterion.com> Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Lucy Liu 提交于
The skb priority to vlan-qos egress mapping that can be configured using set_egress_map with vconfig is overriden by the DCB code in the driver. This patch allows this existing mechanism to work and will increase the configuration flexibility of DCB mode on Linux. A hierarchy of configuration is: 1. Modifies the ixgbe_select_queue() routine for DCB mode to return the priority value from the VLAN tag. It will normally be zero, unless the egress priority map has modified it. This will get packets into the correct queue and result in the queue_mapping field being set correctly. 2. Any tc filter which modifies queue_mapping will be honored, as the filters are handled after the vlan egress map is handled. Signed-off-by: NLucy Liu <lucy.liu@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 sarveshwarb 提交于
This patch is a bug fix to avoid system going into a bad state when driver is loaded in context of kdump kernel. The patch fixes the issue by performing a soft reset of pci function at probe time. Signed-off-by: Nsarveshwarb <sarveshwarb@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jan Engelhardt 提交于
This sockopt goes in line with SO_TYPE and SO_PROTOCOL. It makes it possible for userspace programs to pass around file descriptors — I am referring to arguments-to-functions, but it may even work for the fd passing over UNIX sockets — without needing to also pass the auxiliary information (PF_INET6/IPPROTO_TCP). Signed-off-by: NJan Engelhardt <jengelh@medozas.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jan Engelhardt 提交于
Similar to SO_TYPE returning the socket type, SO_PROTOCOL allows to retrieve the protocol used with a given socket. I am not quite sure why we have that-many copies of socket.h, and why the values are not the same on all arches either, but for where hex numbers dominate, I use 0x1029 for SO_PROTOCOL as that seems to be the next free unused number across a bunch of operating systems, or so Google results make me want to believe. SO_PROTOCOL for others just uses the next free Linux number, 38. Signed-off-by: NJan Engelhardt <jengelh@medozas.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dhananjay Phadke 提交于
Add support to handle aggregate packets from firmware. Local TCP flows are automatically identified by firmware based on the dest IP hash added by driver for local IP addresses. The packets are sent down on the jumbo rx ring. Signed-off-by: NNarender Kumar <narender.kumar@qlogic.com> Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dhananjay Phadke 提交于
Remove unnecessary offsetof calulations on these structures: netxen_board_info, netxen_user_old_info, netxen_new_user_info. The offsets into the flash are fixed, don't need to be calculated. Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dhananjay Phadke 提交于
Fix the calculation of remaining header length in TSO over vlan device case. This was inadvertently missed out in patch 028afe71 ("netxen: add vlan tx acceleration support"). Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
Starting with version 0.5.1, cpmac is no longer broken. Signed-off-by: NFlorian Fainelli <florian@openwrt.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
Signed-off-by: NFlorian Fainelli <florian@openwrt.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
This patch slows down the MDIO_ALIVE busy waiting to let switches and PHY come up after reset. Previous loop was too quick for IC+175C and ADM6996C/L switches to come up. Signed-off-by: NFlorian Fainelli <florian@openwrt.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
This patch adds support for fixed PHY connected in MII mode to cpmac. We allow external and dumb_switch module parameters to override the PHY detection process since they are always connected with MDIO bus identifier 0. This lets fixed PHYs to be detected correctly and be connected to the their corresponding MDIO bus identifier. Signed-off-by: NFlorian Fainelli <florian@openwrt.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
This patch adds fixed PHY support for the two on-chip cpmac Ethernet adapters. Signed-off-by: NFlorian Fainelli <florian@openwrt.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
This patch fixes the wrong MDIO bus identifier which was set to 0 unconditionaly, suitable for external switches while it is actually 1 for PHYs different than external switches which are autodetected. Signed-off-by: NFlorian Fainelli <florian@openwrt.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jan Engelhardt 提交于
String literals are constant, and usually, we can also tag the array of pointers const too, moving it to the .rodata section. Signed-off-by: NJan Engelhardt <jengelh@medozas.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 8月, 2009 2 次提交
-
-
由 David S. Miller 提交于
Same as how Randy Dunlap fixed the ipv4 side of things. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Randy Dunlap 提交于
Fix build errors when SYSCTLs are not enabled: (.init.text+0x5154): undefined reference to `net_ipv4_ctl_path' (.init.text+0x5176): undefined reference to `register_net_sysctl_table' xfrm4_policy.c:(.exit.text+0x573): undefined reference to `unregister_net_sysctl_table Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 8月, 2009 8 次提交
-
-
由 Eric Dumazet 提交于
Current neigh_periodic_timer() function is fired by timer IRQ, and scans one hash bucket each round (very litle work in fact) As we are supposed to scan whole hash table in 15 seconds, this means neigh_periodic_timer() can be fired very often. (depending on the number of concurrent hash entries we stored in this table) Converting this to a workqueue permits scanning whole table, minimizing icache pollution, and firing this work every 15 seconds, independantly of hash table size. This 15 seconds delay is not a hard number, as work is a deferrable one. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hannes Eder 提交于
Since pr_err and friends are used instead of printk there is no point in keeping IP_VS_ERR and friends. Furthermore make use of '__func__' instead of hard coded function names. Signed-off-by: NHannes Eder <heder@google.com> Acked-by: NSimon Horman <horms@verge.net.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Steve Glendinning 提交于
The eeprom read & write commands currently check the E2P_CMD_LOADED_ bit is set before allowing any operations. This prevents any reading or writing unless a correctly programmed EEPROM is installed. This patch removes the check, so it is possible to program blank EEPROMS via ethtool. Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Gerrit Renker 提交于
This renames away a variable clash: * ipv6_table[] is declared as a static global table; * ipv6_sysctl_net_init() uses ipv6_table to refer/destroy dynamic memory; * ipv6_sysctl_net_exit() also uses ipv6_table for the same purpose; * both the two last functions call kfree() on ipv6_table. Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Julia Lawall 提交于
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d but is perhaps more readable. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @haskernel@ @@ #include <linux/kernel.h> @depends on haskernel@ expression x,__divisor; @@ - (((x) + ((__divisor) / 2)) / (__divisor)) + DIV_ROUND_CLOSEST(x,__divisor) // </smpl> Signed-off-by: NJulia Lawall <julia@diku.dk> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Julia Lawall 提交于
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d but is perhaps more readable. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @haskernel@ @@ #include <linux/kernel.h> @depends on haskernel@ expression x,__divisor; @@ - (((x) + ((__divisor) / 2)) / (__divisor)) + DIV_ROUND_CLOSEST(x,__divisor) // </smpl> Signed-off-by: NJulia Lawall <julia@diku.dk> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Divy Le Ray 提交于
Modify control register settings to accommodate the bridge's max read requset size. Signed-off-by: NDivy Le Ray <divy@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Divy Le Ray 提交于
Fix a cut'n paste error in the AEL2020 twinax EDC file name Signed-off-by: NDivy Le Ray <divy@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 02 8月, 2009 12 次提交
-
-
由 Dean Nelson 提交于
PCI drivers that implement the struct pci_error_handlers' error_detected callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is pci_channel_io_perm_failure. This patch fixes the issue for vxge. Signed-off-by: NDean Nelson <dnelson@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dean Nelson 提交于
PCI drivers that implement the struct pci_error_handlers' error_detected callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is pci_channel_io_perm_failure. This patch fixes the issue for s2io. Signed-off-by: NDean Nelson <dnelson@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dean Nelson 提交于
PCI drivers that implement the struct pci_error_handlers' error_detected callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is pci_channel_io_perm_failure. This patch fixes the issue for qlge. Signed-off-by: NDean Nelson <dnelson@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dean Nelson 提交于
PCI drivers that implement the struct pci_error_handlers' error_detected callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is pci_channel_io_perm_failure. This patch fixes the issue for ixgb. Signed-off-by: NDean Nelson <dnelson@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dean Nelson 提交于
PCI drivers that implement the struct pci_error_handlers' error_detected callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is pci_channel_io_perm_failure. This patch fixes the issue for igbvf. Signed-off-by: NDean Nelson <dnelson@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dean Nelson 提交于
PCI drivers that implement the struct pci_error_handlers' error_detected callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is pci_channel_io_perm_failure. This patch fixes the issue for bnx2x. Signed-off-by: NDean Nelson <dnelson@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dean Nelson 提交于
PCI drivers that implement the struct pci_error_handlers' error_detected callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is pci_channel_io_perm_failure. This patch fixes the issue for bnx2. Signed-off-by: NDean Nelson <dnelson@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dean Nelson 提交于
PCI drivers that implement the struct pci_error_handlers' error_detected callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is pci_channel_io_perm_failure. This patch fixes the issue for atl1e. Signed-off-by: NDean Nelson <dnelson@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dean Nelson 提交于
PCI drivers that implement the struct pci_error_handlers' error_detected callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is pci_channel_io_perm_failure. This patch fixes the issue for atl1c. Signed-off-by: NDean Nelson <dnelson@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sathya Perla 提交于
When the driver loads the POST stage of the card is expected to be POST_STAGE_ARMFW_RDY. Signed-off-by: NSathya Perla <sathyap@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sathya Perla 提交于
be_mbox_db_ring() has been changed to be_mbox_notify() (to be consistent with be_mcc_notify()) and struct be_mcc_cq_entry changed to be_mcc_compl to be consistent with rx/tx_compl. Signed-off-by: NSathya Perla <sathyap@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sathya Perla 提交于
And get rid of some unnecessary printks. Signed-off-by: NSathya Perla <sathyap@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-