This patch (as1654) fixes a very old bug in ehci-hcd, connected with
scheduling of periodic split transfers.  The calculations for
full/low-speed bus usage are all carried out after the correction for
bit-stuffing has been applied, but the values in the max_tt_usecs
array assume it hasn't been.  The array should allow for allocation of
up to 90% of the bus capacity, which is 900 us, not 780 us.

The symptom caused by this bug is that any isochronous transfer to a
full-speed device with a maxpacket size larger than about 980 bytes is
always rejected with a -ENOSPC error.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1653) fixes a bug in ehci-hcd.  Unlike iTD entries, an
siTD entry in the periodic schedule may not complete until the frame
after the one it belongs to.  Consequently, when scanning the periodic
schedule it is necessary to start with the frame _preceding_ the one
where the previous scan ended.

Not doing this properly can result in memory leaks and failures to
complete isochronous URBs.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NAndy Leiserson <andy@leiserson.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add PID and special handling for Telit LE920
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add VID and PID for Telit Gobi QDL device
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1652) fixes a long-standing bug in ehci-hcd.  The driver
relies on status polls to know when to stop port-resume signalling.
It uses the root-hub status timer to schedule these status polls.  But
when the driver for the root hub is resumed, the timer is rescheduled
to go off immediately -- before the port is ready.  When this happens
the timer does not get re-enabled, which prevents the port resume from
finishing until some other event occurs.

The symptom is that when a new device is plugged in, it doesn't get
recognized or enumerated until lsusb is run or something else happens.

The solution is to re-enable the root-hub status timer after every
status poll while a port resume is in progress.

This bug hasn't surfaced before now because we never used to try to
suspend the root hub in the middle of a port resume (except by
coincidence).
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: NNorbert Preining <preining@logic.at>
Tested-by: NMing Lei <ming.lei@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1651) adds calls to the new
usb_hcd_{start,end}_port_resume() functions to uhci-hcd.  Now UHCI
root hubs won't be runtime suspended while they are sending a resume
signal to one of their ports.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1650) adds calls to the new
usb_hcd_{start,end}_port_resume() functions to ehci-hcd.  Now EHCI
root hubs won't be runtime suspended while they are sending a resume
signal to one of their ports.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1649) adds a mechanism for host controller drivers to
inform usbcore when they have begun or ended resume signalling on a
particular root-hub port.  The core will then make sure that the root
hub does not get runtime-suspended while the port resume is going on.

Since commit 596d789a (USB: set hub's
default autosuspend delay as 0), the system tries to suspend hubs
whenever they aren't in use.  While a root-hub port is being resumed,
the root hub does not appear to be in use.  Attempted runtime suspends
fail because of the ongoing port resume, but the PM core just keeps on
trying over and over again.  We want to prevent this wasteful effort.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1648) fixes a regression affecting nVidia EHCI
controllers.  Evidently they don't like to have more than one async QH
unlinked at a time.  I can't imagine how they manage to mess it up,
but at least one of them does.

The patch changes the async unlink logic in two ways:

	Each time an IAA cycle is started, only the first QH on the
	async unlink list is handled (rather than all of them).

	Async QHs do not all get unlinked as soon as they have been
	empty for long enough.  Instead, only the last one (i.e., the
	one that has been on the schedule the longest) is unlinked,
	and then only if no other unlinks are in progress at the time.

This means that when multiple QHs are empty, they won't be unlinked as
quickly as before.  That's okay; it won't affect correct operation of
the driver or add an excessive load.  Multiple unlinks tend to be
relatively rare in any case.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: NPiergiorgio Sartor <piergiorgio.sartor@nexgo.de>
Cc: stable <stable@vger.kernel.org> # 3.6
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1647) attempts to work around a problem that seems to
affect some nVidia EHCI controllers.  They sometimes take a very long
time to turn off their async or periodic schedules.  I don't know if
this is a result of other problems, but in any case it seems wise not
to depend on schedule enables or disables taking effect in any
specific length of time.

The patch removes the existing 20-ms timeout for enabling and
disabling the schedules.  The driver will now continue to poll the
schedule state at 1-ms intervals until the controller finally decides
to obey the most recent command issued by the driver.  Just in case
this hides a problem, a debugging message will be logged if the
controller takes longer than 20 polls.

I don't know if this will actually fix anything, but it can't hurt.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NPiergiorgio Sartor <piergiorgio.sartor@nexgo.de>
CC: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Usb3.0 device defines function remote wakeup which is only for interface
recipient rather than device recipient. This is different with usb2.0 device's
remote wakeup feature which is defined for device recipient. According usb3.0
spec 9.4.5, the function remote wakeup can be modified by the SetFeature()
requests using the FUNCTION_SUSPEND feature selector. This patch is to use
correct way to disable usb3.0 device's function remote wakeup after suspend
error and resuming.

This should be backported to kernels as old as 3.4, that contain the
commit 623bef9e "USB/xhci: Enable remote
wakeup for USB3 devices."
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

When the xHCI driver is not available, actively switch the ports to EHCI
mode since some BIOSes leave them in xHCI mode where they would
otherwise appear dead.  This was discovered on a  Dell Optiplex 7010,
but it's possible other systems could be affected.

This should be backported to kernels as old as 3.0, that contain the
commit 69e848c2 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: NDavid Moore <david.moore@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

This patch (as1640) fixes a memory leak in xhci-hcd.  The urb_priv
data structure isn't always deallocated in the handle_tx_event()
routine for non-control transfers.  The patch adds a kfree() call so
that all paths end up freeing the memory properly.

This patch should be backported to kernels as old as 2.6.36, that
contain the commit 8e51adcc "USB: xHCI:
Introduce urb_priv structure"
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-and-tested-by: NMartin Mokrejs <mmokrejs@fold.natur.cuni.cz>
CC: <stable@vger.kernel.org>

Fix incorrect bit test that originally showed up in
4ee823b8 "USB/xHCI: Support
device-initiated USB 3.0 resume."

Use '&' instead of '&&'.

This should be backported to kernels as old as 3.4.
Signed-off-by: NNickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

To calculate the TD size for a particular TRB in an isoc TD, we need
know the endpoint's max packet size.  Isochronous endpoints also encode
the number of additional service opportunities in their wMaxPacketSize
field.  The TD size calculation did not mask off those bits before using
the field.  This resulted in incorrect TD size information for
isochronous TRBs when an URB frame buffer crossed a 64KB boundary.

For example:
 - an isoc endpoint has 2 additional service opportunites and
   a max packet size of 1020 bytes
 - a frame transfer buffer contains 3060 bytes
 - one frame buffer crosses a 64KB boundary, and must be split into
   one 1276 byte TRB, and one 1784 byte TRB.

The TD size is is the number of packets that remain to be transferred
for a TD after processing all the max packet sized packets in the
current TRB and all previous TRBs.

For this TD, the number of packets to be transferred is (3060 / 1020),
or 3.  The first TRB contains 1276 bytes, which means it contains one
full packet, and a 256 byte remainder.  After processing all the max
packet-sized packets in the first TRB, the host will have 2 packets left
to transfer.

The old code would calculate the TD size for the first TRB as:

total packet count = DIV_ROUND_UP (TD length / endpoint wMaxPacketSize)
total packet count - (first TRB length / endpoint wMaxPacketSize)

The math should have been:

total packet count = DIV_ROUND_UP (3060 / 1020) = 3
3 - (1276 / 1020) = 2

Since the old code didn't mask off the additional service interval bits
from the wMaxPacketSize field, the math ended up as

total packet count = DIV_ROUND_UP (3060 / 5116) = 1
1 - (1276 / 5116) = 1

Fix this by masking off the number of additional service opportunities
in the wMaxPacketSize field.

This patch should be backported to stable kernels as old as 3.0, that
contain the commit 4da6e6f2 "xhci 1.0:
Update TD size field format."  It may not apply well to kernels older
than 3.2 because of commit 29cc8897
"USB: use usb_endpoint_maxp() instead of le16_to_cpu()".
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

An isochronous TD is comprised of one isochronous TRB chained to zero or
more normal TRBs.  Only the isoc TRB has the TBC and TLBPC fields.  The
normal TRBs must set those fields to zeroes.  The code was setting the
TBC and TLBPC fields for both isoc and normal TRBs.  Fix this.

This should be backported to stable kernels as old as 3.0, that contain
the commit b61d378f " xhci 1.0: Set
transfer burst last packet count field."
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

This patch (as1643b) fixes a build error in ehci-hcd when compiling for
ARM with allmodconfig:

drivers/usb/host/ehci-hcd.c:1285:0: warning: "PLATFORM_DRIVER" redefined [enabled by default]
drivers/usb/host/ehci-hcd.c:1255:0: note: this is the location of the previous definition
drivers/usb/host/ehci-mxc.c:280:31: warning: 'ehci_mxc_driver' defined but not used [-Wunused-variable]
drivers/usb/host/ehci-hcd.c:1285:0: warning: "PLATFORM_DRIVER" redefined [enabled by default]
drivers/usb/host/ehci-hcd.c:1255:0: note: this is the location of the previous definition

The fix is to convert ehci-mxc over to the new "ehci-hcd is a library"
scheme so that it can coexist peacefully with the ehci-platform
driver.  As part of the conversion the ehci_mxc_priv data structure,
which was allocated dynamically, is now placed where it belongs: in
the private area at the end of struct ehci_hcd.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1642) adds an ehci->priv field for private use by EHCI
platform drivers.  The space was provided some time ago, but it didn't
have a name.

Until now none of the platform drivers has used this private space,
but that's about to change in the next patch of this series.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1641) fixes a minor bug in ehci-hcd left over from when
the Chipidea driver was converted to the "ehci-hcd is a library"
scheme.  The test for whether the Chipidea platform driver is active
should be IS_ENABLED(), not defined().
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Without this, platform drivers e.g. ehci-omap.c will see a
different version of struct ehci_hcd than ehci-hcd.c and
break reference to 'debug_dir' and 'priv' members when
CONFIG_USB_DEBUG is enabled.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1644) fixes a race that occurs during startup in
uhci-hcd.  If the IRQ line is shared with other devices, it's possible
for the handler routine to be called before the data structures are
fully initialized.

The problem is fixed by adding a check to the IRQ handler routine.  If
the initialization hasn't finished yet, the routine will return
immediately.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NDon Zickus <dzickus@redhat.com>
Tested-by: N"Huang, Adrian (ISS Linux TW)" <adrian.huang@hp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add missing braces around an if block in ffs_fs_parse_opts. This broke
parsing the uid/gid mount options and causes mount to fail when using
uid/gid. This has been introduced by commit b9b73f7c (userns: Convert usb
functionfs to use kuid/kgid where appropriate) in 3.7.

Cc: <stable@vger.kernel.org>
Signed-off-by: NBenoit Goby <benoit@android.com>
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

dwc3_gadget_set_ep_config expects maxburst as incremented by 1. So, by
default initialize ep->maxburst to 1 for ep0.

Cc: <stable@vger.kernel.org>
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

As mach/hardware.h is deleted, we can't visit platform code at driver.
It has no phy driver to combine with this controller, so it has to use
ioremap to map phy address as a workaround.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

As mach/hardware.h is deleted, we need to use platform_device_id to
differentiate SoCs. Besides, one cpu_is_mx35 is useless as it has
already used pdata to differentiate runtime

Meanwhile we update the platform code accordingly.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch fixes the following:

WARNING: vmlinux.o(.text+0x1e709c): Section mismatch in reference from the funct
ion dma_controller_create() to the function .init.text:cppi_controller_start()
The function dma_controller_create() references
the function __init cppi_controller_start().
This is often because dma_controller_create lacks a __init
annotation or the annotation of cppi_controller_start is wrong.

This warning is there due to the deficiency in the commit 07a67bbb (usb: musb:
Make dma_controller_create __devinit).

Since the start() method is only called from musb_init_controller() which is
not annotated, drop '__init' annotation from cppi_controller_start() and also
cppi_pool_init() since it gets called from that function, to avoid another
section mismatch warning...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@vger.kernel.org # 3.7+
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The tty is NULL when the port is hanging up.
chase_port() needs to check for this.

This patch is intended for stable series.
The behavior was observed and tested in Linux 3.2 and 3.7.1.

Johan Hovold submitted a more elaborate patch for the mainline kernel.

[   56.277883] usb 1-1: edge_bulk_in_callback - nonzero read bulk status received: -84
[   56.278811] usb 1-1: USB disconnect, device number 3
[   56.278856] usb 1-1: edge_bulk_in_callback - stopping read!
[   56.279562] BUG: unable to handle kernel NULL pointer dereference at 00000000000001c8
[   56.280536] IP: [<ffffffff8144e62a>] _raw_spin_lock_irqsave+0x19/0x35
[   56.281212] PGD 1dc1b067 PUD 1e0f7067 PMD 0
[   56.282085] Oops: 0002 [#1] SMP
[   56.282744] Modules linked in:
[   56.283512] CPU 1
[   56.283512] Pid: 25, comm: khubd Not tainted 3.7.1 #1 innotek GmbH VirtualBox/VirtualBox
[   56.283512] RIP: 0010:[<ffffffff8144e62a>]  [<ffffffff8144e62a>] _raw_spin_lock_irqsave+0x19/0x35
[   56.283512] RSP: 0018:ffff88001fa99ab0  EFLAGS: 00010046
[   56.283512] RAX: 0000000000000046 RBX: 00000000000001c8 RCX: 0000000000640064
[   56.283512] RDX: 0000000000010000 RSI: ffff88001fa99b20 RDI: 00000000000001c8
[   56.283512] RBP: ffff88001fa99b20 R08: 0000000000000000 R09: 0000000000000000
[   56.283512] R10: 0000000000000000 R11: ffffffff812fcb4c R12: ffff88001ddf53c0
[   56.283512] R13: 0000000000000000 R14: 00000000000001c8 R15: ffff88001e19b9f4
[   56.283512] FS:  0000000000000000(0000) GS:ffff88001fd00000(0000) knlGS:0000000000000000
[   56.283512] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[   56.283512] CR2: 00000000000001c8 CR3: 000000001dc51000 CR4: 00000000000006e0
[   56.283512] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   56.283512] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[   56.283512] Process khubd (pid: 25, threadinfo ffff88001fa98000, task ffff88001fa94f80)
[   56.283512] Stack:
[   56.283512]  0000000000000046 00000000000001c8 ffffffff810578ec ffffffff812fcb4c
[   56.283512]  ffff88001e19b980 0000000000002710 ffffffff812ffe81 0000000000000001
[   56.283512]  ffff88001fa94f80 0000000000000202 ffffffff00000001 0000000000000296
[   56.283512] Call Trace:
[   56.283512]  [<ffffffff810578ec>] ? add_wait_queue+0x12/0x3c
[   56.283512]  [<ffffffff812fcb4c>] ? usb_serial_port_work+0x28/0x28
[   56.283512]  [<ffffffff812ffe81>] ? chase_port+0x84/0x2d6
[   56.283512]  [<ffffffff81063f27>] ? try_to_wake_up+0x199/0x199
[   56.283512]  [<ffffffff81263a5c>] ? tty_ldisc_hangup+0x222/0x298
[   56.283512]  [<ffffffff81300171>] ? edge_close+0x64/0x129
[   56.283512]  [<ffffffff810612f7>] ? __wake_up+0x35/0x46
[   56.283512]  [<ffffffff8106135b>] ? should_resched+0x5/0x23
[   56.283512]  [<ffffffff81264916>] ? tty_port_shutdown+0x39/0x44
[   56.283512]  [<ffffffff812fcb4c>] ? usb_serial_port_work+0x28/0x28
[   56.283512]  [<ffffffff8125d38c>] ? __tty_hangup+0x307/0x351
[   56.283512]  [<ffffffff812e6ddc>] ? usb_hcd_flush_endpoint+0xde/0xed
[   56.283512]  [<ffffffff8144e625>] ? _raw_spin_lock_irqsave+0x14/0x35
[   56.283512]  [<ffffffff812fd361>] ? usb_serial_disconnect+0x57/0xc2
[   56.283512]  [<ffffffff812ea99b>] ? usb_unbind_interface+0x5c/0x131
[   56.283512]  [<ffffffff8128d738>] ? __device_release_driver+0x7f/0xd5
[   56.283512]  [<ffffffff8128d9cd>] ? device_release_driver+0x1a/0x25
[   56.283512]  [<ffffffff8128d393>] ? bus_remove_device+0xd2/0xe7
[   56.283512]  [<ffffffff8128b7a3>] ? device_del+0x119/0x167
[   56.283512]  [<ffffffff812e8d9d>] ? usb_disable_device+0x6a/0x180
[   56.283512]  [<ffffffff812e2ae0>] ? usb_disconnect+0x81/0xe6
[   56.283512]  [<ffffffff812e4435>] ? hub_thread+0x577/0xe82
[   56.283512]  [<ffffffff8144daa7>] ? __schedule+0x490/0x4be
[   56.283512]  [<ffffffff8105798f>] ? abort_exclusive_wait+0x79/0x79
[   56.283512]  [<ffffffff812e3ebe>] ? usb_remote_wakeup+0x2f/0x2f
[   56.283512]  [<ffffffff812e3ebe>] ? usb_remote_wakeup+0x2f/0x2f
[   56.283512]  [<ffffffff810570b4>] ? kthread+0x81/0x89
[   56.283512]  [<ffffffff81057033>] ? __kthread_parkme+0x5c/0x5c
[   56.283512]  [<ffffffff8145387c>] ? ret_from_fork+0x7c/0xb0
[   56.283512]  [<ffffffff81057033>] ? __kthread_parkme+0x5c/0x5c
[   56.283512] Code: 8b 7c 24 08 e8 17 0b c3 ff 48 8b 04 24 48 83 c4 10 c3 53 48 89 fb 41 50 e8 e0 0a c3 ff 48 89 04 24 e8 e7 0a c3 ff ba 00 00 01 00
<f0> 0f c1 13 48 8b 04 24 89 d1 c1 ea 10 66 39 d1 74 07 f3 90 66
[   56.283512] RIP  [<ffffffff8144e62a>] _raw_spin_lock_irqsave+0x19/0x35
[   56.283512]  RSP <ffff88001fa99ab0>
[   56.283512] CR2: 00000000000001c8
[   56.283512] ---[ end trace 49714df27e1679ce ]---
Signed-off-by: NWolfgang Frisch <wfpub@roembden.net>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver description files gives these names to the vendor specific
functions on this modem:

 Diagnostics VID_2357&PID_0201&MI_00
 NMEA        VID_2357&PID_0201&MI_01
 Modem       VID_2357&PID_0201&MI_03
 Networkcard VID_2357&PID_0201&MI_04
Reported-by: NThomas Schäfer <tschaefer@t-online.de>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver description files gives these names to the vendor specific
functions on this modem:

 Diag   VID_19D2&PID_0265&MI_00
 NMEA   VID_19D2&PID_0265&MI_01
 AT cmd VID_19D2&PID_0265&MI_02
 Modem  VID_19D2&PID_0265&MI_03
 Net    VID_19D2&PID_0265&MI_04
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Simple fix to add support for Crucible Technologies COMET Caller ID
USB decoder - a device containing FTDI USB/Serial converter chip,
handling 1200bps CallerID messages decoded from the phone line -
adding correct USB PID is sufficient.

Tested to apply cleanly and work flawlessly against 3.6.9, 3.7.0-rc8
and 3.8.0-rc3 on both amd64 and x86 arches.
Signed-off-by: NTomasz Mloduchowski <q@qdot.me>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the following compile warning:

In file included from drivers/usb/host/ohci-hcd.c:1170:0:
drivers/usb/host/ohci-tmio.c: In function 'tmio_start_hc':
drivers/usb/host/ohci-tmio.c:130:2: warning: format '%llx' expects argument of type 'long long unsigned int', but argument 4 has type 'resource_size_t' [-Wformat]

seen on ARM 32-bit builds.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add device quirk for Microsoft Lifecam VX700 v2.0 webcams.
Fixes squeaking noise of the microphone.
Signed-off-by: NAndreas Fleig <andreasfleig@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

mpc5121e doesn't have system interface registers, accessing this
register address space cause the machine check exception and a
kernel crash:

...
Machine check in kernel mode.
Caused by (from SRR1=49030): Transfer error ack signal
Oops: Machine check, sig: 7 [#1]
MPC5121 ADS
Modules linked in:
NIP: c025fd60 LR: c0265bb4 CTR: 00000000
REGS: df82dac0 TRAP: 0200   Not tainted
(3.7.0-rc7-00641-g81e6c91)
MSR: 00049030 <EE,ME,IR,DR>  CR: 42002024  XER: 20000000
TASK = df824b70[1] 'swapper' THREAD: df82c000
GPR00: 00000000 df82db70 df824b70 df3ed0f0 00000003 00000000 00000000 00000000
GPR08: 00000020 32000000 c03550ec 20000000 22002028 00000000 c0003f5c 00000000
GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 c0423898 c0450000
GPR24: 00000077 00000002 e5086180 1c000c00 e5086000 df33ec00 00000003 df34e000
NIP [c025fd60] ehci_fsl_setup_phy+0xd0/0x354
LR [c0265bb4] ehci_fsl_setup+0x220/0x284
...

Fix it by checking 'have_sysif_regs' flag before register access.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When running a scp transfer using a USB/Ethernet adapter the following crash
happens:

$ scp test.tar.gz fabio@192.168.1.100:/home/fabio
fabio@192.168.1.100's password:
test.tar.gz                                      0%    0     0.0KB/s   --:-- ETA
------------[ cut here ]------------
WARNING: at net/sched/sch_generic.c:255 dev_watchdog+0x2cc/0x2f0()
NETDEV WATCHDOG: eth0 (asix): transmit queue 0 timed out
Modules linked in:
Backtrace:
[<80011c94>] (dump_backtrace+0x0/0x10c) from [<804d3a5c>] (dump_stack+0x18/0x1c)
 r6:000000ff r5:80412388 r4:80685dc0 r3:80696cc0
[<804d3a44>] (dump_stack+0x0/0x1c) from [<80021868>]
(warn_slowpath_common+0x54/0x6c)
[<80021814>] (warn_slowpath_common+0x0/0x6c) from [<80021924>]
(warn_slowpath_fmt+0x38/0x40)
...

Setting SDIS (Stream Disable Mode- bit 4 of USBMODE register) fixes the problem.

However, in current code CI13XXX_DISABLE_STREAMING flag is only set in udc mode,
so allow disabling streaming also in host mode.

Tested on a mx6qsabrelite board.
Suggested-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

fsl-ehci probing fails on mpc5121e:
...
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: Could not get controller version
fsl-ehci fsl-ehci.0: can't setup
fsl-ehci fsl-ehci.0: USB bus 1 deregistered
fsl-ehci fsl-ehci.0: init fsl-ehci.0 fail, -22
fsl-ehci: probe of fsl-ehci.0 failed with error -22

Fix it by returning appropriate version info for mpc5121, too.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 09f6ffde (USB: EHCI: fix build error by making ChipIdea host a
normal EHCI driver) introduced a dependency on USB_EHCI_HCD for the
chipidea USB host driver, that in turns depends on USB_ARCH_HAS_EHCI.

If this symbol is not set for MXS, the MXS boards are not able to use
the chipidea driver anymore.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Some touchscreens have buggy firmware which claims
remote wakeup to be enabled after a reset. They nevertheless
crash if the feature is cleared by the host.
Add a check for reset resume before checking for
an enabled remote wakeup feature. On compliant
devices the feature must be cleared after a reset anyway.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding support "PSC Scanning, Magellan 800i" in cdc-acm

Very simple, but very necessary.
Suitable for all versions of the kernel > 2.6
Signed-off-by: NDenis N Ladin <denladin@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Hyundai Petatel Inc. Nexpring NP10T terminal (EV-DO rev.A USB modem) ID
Signed-off-by: NDenis Kaganovich <mahatma@eu.by>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

also known as Alcatel One Touch L100V LTE

The driver description files gives these names to the vendor specific
functions on this modem:

 Application1: VID_1BBB&PID_011E&MI_00
 Application2: VID_1BBB&PID_011E&MI_01
 Modem:        VID_1BBB&PID_011E&MI_03
 Ethernet:     VID_1BBB&PID_011E&MI_04
Reported-by: NThomas Schäfer <tschaefer@t-online.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>