This patch adds flow control support on A2.
Co-developed-by: NDmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: NDmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds EEE support on A2.
Signed-off-by: NNikita Danilov <ndanilov@marvell.com>
Co-developed-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes 2.5G baseX wrong usage/reporting, since it shouldn't have
been mixed with baseT.
Signed-off-by: NNikita Danilov <ndanilov@marvell.com>
Signed-off-by: NMark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for 10M/100M/1G half duplex rates, which are
supported by A2 in additional to full duplex rates supported by A1.
Signed-off-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

arg cannot be NULL since its already being dereferenced
before. Remove the redundant NULL check.
Signed-off-by: NGaurav Singh <gaurav1086@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert the mtk_eth_soc driver to use the finalised link parameters in
mac_link_up() rather than the parameters in mac_config().
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Multicast improvement in Ocelot and Felix drivers

This series makes some basic multicast forwarding functionality work for
Felix DSA and for Ocelot switchdev. IGMP/MLD snooping in Felix is still
missing, and there are other improvements to be made in the general area
of multicast address filtering towards the CPU, but let's get these
hardware-specific fixes out of the way first.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current procedure for installing a multicast address is hardcoded
for IPv4. But, in the ocelot hardware, there are 3 different procedures
for IPv4, IPv6 and for regular L2 multicast.

For IPv6 (33-33-xx-xx-xx-xx), it's the same as for IPv4
(01-00-5e-xx-xx-xx), except that the destination port mask is stuffed
into first 2 bytes of the MAC address except into first 3 bytes.

For plain Ethernet multicast, there's no port-in-address stuffing going
on, instead the DEST_IDX (pointer to PGID) is used there, just as for
unicast. So we have to use one of the nonreserved multicast PGIDs that
the hardware has allocated for this purpose.

This patch classifies the type of multicast address based on its first
bytes, then redirects to one of the 3 different hardware procedures.

Note that this gives us a really better way of redirecting PTP frames
sent at 01-1b-19-00-00-00 to the CPU. Previously, Yangbo Lu tried to add
a trapping rule for PTP EtherType but got a lot of pushback:

https://patchwork.ozlabs.org/project/netdev/patch/20190813025214.18601-5-yangbo.lu@nxp.com/

But right now, that isn't needed at all. The application stack (ptp4l)
does this for the PTP multicast addresses it's interested in (which are
configurable, and include 01-1b-19-00-00-00):

	memset(&mreq, 0, sizeof(mreq));
	mreq.mr_ifindex = index;
	mreq.mr_type = PACKET_MR_MULTICAST;
	mreq.mr_alen = MAC_LEN;
	memcpy(mreq.mr_address, addr1, MAC_LEN);

	err1 = setsockopt(fd, SOL_PACKET, PACKET_ADD_MEMBERSHIP, &mreq,
			  sizeof(mreq));

Into the kernel, this translates into a dev_mc_add on the switch network
interfaces, and our drivers know that it means they should translate it
into a host MDB address (make the CPU port be the destination).
Previously, this was broken because all mdb addresses were treated as
IPv4 (which 01-1b-19-00-00-00 obviously is not).
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current iterators are impossible to understand at first glance
without switching back and forth between the definitions and their
actual use in the for loops.

So introduce some convenience names to help readability.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the mdb hooks in felix and exports the mdb functions from
ocelot.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When used in DSA mode (as seen in Felix), the DEST_IDX in the MAC table
should point to the PGID for the CPU port (PGID_CPU) and not for the
Ethernet port where the CPU queues are redirected to (also known as Node
Processor Interface - NPI).

Because for Felix this distinction shouldn't really matter (from DSA
perspective, the NPI port _is_ the CPU port), make the ocelot library
act upon the CPU port when NPI mode is enabled. This has no effect for
the mscc_ocelot driver for VSC7514, because that does not use NPI (and
ocelot->npi is -1).
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ocelot hardware designers have made some hacks to support multicast
IPv4 and IPv6 addresses. Normally, the MAC table matches on MAC
addresses and the destination ports are selected through the DEST_IDX
field of the respective MAC table entry. The DEST_IDX points to a Port
Group ID (PGID) which contains the bit mask of ports that frames should
be forwarded to. But there aren't a lot of PGIDs (only 80 or so) and
there are clearly many more IP multicast addresses than that, so it
doesn't scale to use this PGID mechanism, so something else was done.
Since the first portion of the MAC address is known, the hack they did
was to use a single PGID for _flooding_ unknown IPv4 multicast
(PGID_MCIPV4 == 62), but for known IP multicast, embed the destination
ports into the first 3 bytes of the MAC address recorded in the MAC
table.

The VSC7514 datasheet explains it like this:

    3.9.1.5 IPv4 Multicast Entries

    MAC table entries with the ENTRY_TYPE = 2 settings are interpreted
    as IPv4 multicast entries.
    IPv4 multicasts entries match IPv4 frames, which are classified to
    the specified VID, and which have DMAC = 0x01005Exxxxxx, where
    xxxxxx is the lower 24 bits of the MAC address in the entry.
    Instead of a lookup in the destination mask table (PGID), the
    destination set is programmed as part of the entry MAC address. This
    is shown in the following table.

    Table 78: IPv4 Multicast Destination Mask

        Destination Ports            Record Bit Field
        ---------------------------------------------
        Ports 10-0                   MAC[34-24]

    Example: All IPv4 multicast frames in VLAN 12 with MAC 01005E112233 are
    to be forwarded to ports 3, 8, and 9. This is done by inserting the
    following entry in the MAC table entry:
    VALID = 1
    VID = 12
    MAC = 0x000308112233
    ENTRY_TYPE = 2
    DEST_IDX = 0

But this procedure is not at all what's going on in the driver. In fact,
the code that embeds the ports into the MAC address looks like it hasn't
actually been tested. This patch applies the procedure described in the
datasheet.

Since there are many other fixes to be made around multicast forwarding
until it works properly, there is no real reason for this patch to be
backported to stable trees, or considered a real fix of something that
should have worked.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Offload TC action pedit munge tcp/udp sport/dport

Petr says:

On Spectrum-2 and Spectrum-3, it is possible to overwrite L4 port number of
a TCP or UDP packet in the ACL engine. That corresponds to the pedit munges
of tcp and udp sport resp. dport fields. Offload these munges on the
systems where they are supported.

The current offloading code assumes that all systems support the same set
of fields. This now changes, so in patch #1 first split handling of pedit
munges by chip type. The analysis of which packet field a given munge
describes is kept generic.

Patch #2 introduces the new flexible action fields. Patch #3 then adds the
new pedit fields, and dispatches on them on Spectrum>1.

Patch #4 adds a forwarding selftest for pedit dsfield, applicable to SW as
well as HW datapaths.
====================
Reviewed-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a test that checks that pedit adjusts port numbers of tcp and udp
packets.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Spectrum-2 supports an ACL action L4_PORT, which allows TCP and UDP source
and destination port number change. Offload suitable mangles to this
action.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add fields related to L4_PORT_ACTION, which is used for changing of TCP and
UDP port numbers.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Certain ACL actions are only available on some Spectrum revisions. In
particular, L4_PORT_ACTION is not available on Spectrum-1. Introduce a
new ops struct intended to hold these differences, mlxsw_sp_rulei_ops.
Prime it with a sole member, act_mangle_field, meant for handling of
pedit mangles.

Create two ops structures, one for Spectrum-1, the other for Spectrum-2
and above. Add callbacks for act_mangle_field and dispatch to the common
handler.

Invoke mlxsw_sp_rulei_ops.act_mangle_field from the field mangler
instead of calling the common handler directly.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Maxim Kochetkov says:

====================
Add Marvell 88E1340S, 88E1548P support

This patch series add new PHY id support.
Russell King asked to use single style for referencing functions.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for this new phy ID.
Signed-off-by: NMaxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for this new phy ID.
Signed-off-by: NMaxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The kernel in general does not use &func referencing format.
Signed-off-by: NMaxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: mark device as detached in PCI D3 and improve locking

Mark the netdevice as detached whenever parent is in PCI D3hot and not
accessible. This mainly applies to runtime-suspend state.
In addition take RTNL lock in suspend calls, this allows to remove
the driver-specific mutex and improve PM callbacks in general.
====================
Reviewed-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify rtl8169_runtime_resume() by calling rtl8169_resume().
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the critical sections are protected with RTNL lock, we don't
need a separate mutex any longer.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most relevant ops (open, close, ethtool ops) are protected with RTNL
lock by net core. Make sure that such ops can't be interrupted by
e.g. (runtime-)suspending by taking the RTNL lock in suspend ops
and the PCI error handler.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Factor out bringing device up to a new function rtl8169_up(), similar
to rtl8169_down() for bringing the device down.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because the netdevice is marked as detached now when parent is not
accessible we can remove quite some checks.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mark the netdevice as detached whenever we go into PCI D3hot.
This allows to remove some checks e.g. from ethtool ops because
dev_ethtool() checks for netif_device_present() in the beginning.

In this context move waking up the queue out of rtl_reset_work()
because in cases where netif_device_attach() is called afterwards
the queue should be woken up by the latter function only.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A netdevice may be marked as detached because the parent is
runtime-suspended and not accessible whilst interface or link is down.
An example are PCI network devices that go into PCI D3hot, see e.g.
__igc_shutdown() or rtl8169_net_suspend().
If netdevice is down and marked as detached we can only open it if
we runtime-resume it before __dev_open() calls netif_device_present().

Therefore, if netdevice is detached, try to runtime-resume the parent
and only return with an error if it's still detached.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Martin Blumenstingl says:

====================
prepare dwmac-meson8b for G12A specific initialization

Some users are reporting that RGMII (and sometimes also RMII) Ethernet
is not working for them on G12A/G12B/SM1 boards. Upon closer inspection
of the vendor code for these SoCs new register bits are found.

It's not clear yet how these registers work. Add a new compatible string
as the first preparation step to improve Ethernet support on these SoCs.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Amlogic Meson G12A, G12B and SM1 have the same (at least as far as we
know at the time of writing) PRG_ETHERNET glue register implementation.
This implementation however is slightly different from AXG as it now has
an undocument "auto cali idx val" register in PRG_ETH1[17:16] which
seems to be related to RGMII Ethernet.

Add a new compatible string for G12A SoCs so the logic for this new
register can be implemented in the future.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Amlogic Meson G12A, G12B and SM1 have the same (at least as far as we
know at the time of writing) PRG_ETHERNET glue register implementation.
This implementation however is slightly different from AXG as it now has
an undocument "auto cali idx val" register in PRG_ETH1[17:16] which
seems to be related to RGMII Ethernet.

Add a compatible string for G12A and newer so the new registers can be
used.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vasundhara Volam says:

====================
devlink: Add board.serial_number field to info_get cb.

This patchset adds support for board.serial_number to devlink info_get
cb and also use it in bnxt_en driver.

Sample output:

$ devlink dev info pci/0000:af:00.1
pci/0000:af:00.1:
  driver bnxt_en
  serial_number 00-10-18-FF-FE-AD-1A-00
  board.serial_number 433551F+172300000
  versions:
      fixed:
        board.id 7339763 Rev 0.
        asic.id 16D7
        asic.rev 1
      running:
        fw 216.1.216.0
        fw.psid 0.0.0
        fw.mgmt 216.1.192.0
        fw.mgmt.api 1.10.1
        fw.ncsi 0.0.0.0
        fw.roce 216.1.16.0

v2:
- Modify board_serial_number to board.serial_number for maintaining
consistency.
- Combine 2 lines in second patchset as column limit is 100 now
====================
Reviewed-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add board.serial_number field info to info_get cb via devlink,
if driver can fetch the information from the device.

Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: NMichael Chan <michael.chan@broadcom.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Board serial number is a serial number, often available in PCI
*Vital Product Data*.

Also, update devlink-info.rst documentation file.

Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: NMichael Chan <michael.chan@broadcom.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Cosmetic cleanup in SJA1105 DSA driver

This removes the sparse warnings from the sja1105 driver and makes some
structures constant.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since struct sja1105_private only holds a const pointer to one of these
structures based on device tree compatible string, the structures
themselves can be made const.

Also add an empty line between each structure definition, to appease
checkpatch.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The per-chip instantiations of struct sja1105_table_ops and struct
sja1105_dynamic_table_ops can be made constant, so do that.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sparse is complaining and giving the following warning message:
'Using plain integer as NULL pointer'.

This is not what's going on, instead {0} is used as a zero initializer
for the structure members, to indicate that the particular chip revision
does not support those particular config tables.

But since the config tables are declared globally, the unpopulated
elements are zero-initialized anyway. So, to make sparse shut up, let's
remove the zero initializers.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>