The udp_ip4_ind bit is set only for IPv4 UDP non-fragmented packets
so that the hardware can flip the checksum to 0xFFFF if the computed
checksum is 0 per RFC768.

However, this bit had to be set for IPv6 UDP non fragmented packets
as well per hardware requirements. Otherwise, IPv6 UDP packets
with computed checksum as 0 were transmitted by hardware and were
dropped in the network.

In addition to setting this bit for IPv6 UDP, the field is also
appropriately renamed to udp_ind as part of this change.

Fixes: 5eb5f860 ("net: qualcomm: rmnet: Add support for TX checksum offload")
Cc: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure the delayed work for stats update is not pending before
wq destruction.
This fixes the module unload path.
The issue is there since day 1.

Fixes: a556c76a ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: NClaudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hw_ver field was initialized to zero. Return the chip revision.
This is relevant for rdma driver.
Signed-off-by: NMichal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BroadMobi BM818 M.2 card uses the QMI protocol
Signed-off-by: NBob Ham <bob.ham@puri.sm>
Signed-off-by: NAngus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 3968d389 ("bnx2x: Fix Multi-Cos.") which enabled multi-cos
feature after prolonged time in driver added some regression causing
numerous issues (sudden reboots, tx timeout etc.) reported by customers.
We plan to backout this commit and submit proper fix once we have root
cause of issues reported with this feature enabled.

Fixes: 3968d389 ("bnx2x: Fix Multi-Cos.")
Signed-off-by: NSudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: NManish Chopra <manishc@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Align to the naming convention in TLS documentation.

Fixes: 51a5e563 ("nfp: tls: add basic statistics")
Suggested-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

A netdev mismatch in the processed TLS SKB should not occur,
and indicates a kernel bug.
Add WARN_ONCE to spot such cases.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Suggested-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

This patch prevents a race between user invoked cached counters
query and a neighbor last usage updater.

The cached flow counter stats can be queried by calling
"mlx5_fc_query_cached" which provides the number of bytes and
packets that passed via this flow since the last time this counter
was queried.
It does so by reducting the last saved stats from the current, cached
stats and then updating the last saved stats with the cached stats.
It also provide the lastuse value for that flow.

Since "mlx5e_tc_update_neigh_used_value" needs to retrieve the
last usage time of encapsulation flows, it calls the flow counter
query method periodically and async to user queries of the flow counter
using cls_flower.
This call is causing the driver to update the last reported bytes and
packets from the cache and therefore, future user queries of the flow
stats will return lower than expected number for bytes and packets
since the last saved stats in the driver was updated async to the last
saved stats in cls_flower.

This causes wrong stats presentation of encapsulation flows to user.

Since the neighbor usage updater only needs the lastuse stats from the
cached counter, the fix is to use a dedicated lastuse query call that
returns the lastuse value without synching between the cached stats and
the last saved stats.

Fixes: f6dfb4c3 ("net/mlx5e: Update neighbour 'used' state using HW flow rules counters")
Signed-off-by: NAriel Levkovich <lariel@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Speed translation is performed based on legacy or extended PTYS
register. Translate speed with respect to:
1) Capability bit of extended PTYS table.
2) User request:
 a) When auto-negotiation is turned on, inspect advertisement whether it
 contains extended link modes.
 b) When auto-negotiation is turned off, speed > 100Gbps (maximal
 speed supported in legacy mode).
With both conditions fulfilled translation is done with extended PTYS
table otherwise use legacy PTYS table.
Without this patch 25/50/100 Gbps speed cannot be set, since try to
configure in extended mode but read from legacy mode.

Fixes: dd1b9e09 ("net/mlx5: ethtool, Allow legacy link-modes configuration via non-extended ptys")
Signed-off-by: NAya Levin <ayal@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

No XSK support in the enhanced IPoIB driver and representors.
Add a profile property to specify this, and enhance the logic
that calculates the max number of channels to take it into
account.

Fixes: db05815b ("net/mlx5e: Add XSK zero-copy support")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

New flow table type RDMA_RX was added but the MLX5_CAP_FLOW_TABLE_TYPE
didn't handle this new flow table type.
This means that MLX5_CAP_FLOW_TABLE_TYPE returns an empty capability to
this flow table type.

Update both the macro and the maximum supported flow table type to
RDMA_RX.

Fixes: d83eb50e ("net/mlx5: Add support in RDMA RX steering")
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

When lag is active, which is controlled by the bonded mlx5e netdev, mlx5
interface unregestering must happen in the reverse order where rdma is
unregistered (unloaded) first, to guarantee all references to the lag
context in hardware is removed, then remove mlx5e netdev interface which
will cleanup the lag context from hardware.

Without this fix during destroy of LAG interface, we observed following
errors:
 * mlx5_cmd_check:752:(pid 12556): DESTROY_LAG(0x843) op_mod(0x0) failed,
   status bad parameter(0x3), syndrome (0xe4ac33)
 * mlx5_cmd_check:752:(pid 12556): DESTROY_LAG(0x843) op_mod(0x0) failed,
   status bad parameter(0x3), syndrome (0xa5aee8).

Fixes: a31208b1 ("net/mlx5_core: New init and exit flow for mlx5_core")
Reviewed-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NMark Zhang <markz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

fm_set_max_frm() existed in the Freescale SDK as a callback for an
early_param. When this code was ported to the upstream kernel the
early_param was converted to a module_param making the reference to the
function incorrect. The rest of the comment already does a good job of
explaining the parameter so removing the reference to the non-existent
function seems like the best thing to do.
Signed-off-by: NChris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- v1 -> v2: Move skb_set_owner_w to __tun_build_skb to reduce patch size

Small packets going out of a tap device go through an optimized code
path that uses build_skb() rather than sock_alloc_send_pskb(). The
latter calls skb_set_owner_w(), but the small packet code path does not.

The net effect is that small packets are not owned by the userland
application's socket (e.g. QEMU), while large packets are.
This can be seen with a TCP session, where packets are not owned when
the window size is small enough (around PAGE_SIZE), while they are once
the window grows (note that this requires the host to support virtio
tso for the guest to offload segmentation).
All this leads to inconsistent behaviour in the kernel, especially on
netfilter modules that uses sk->socket (e.g. xt_owner).

Fixes: 66ccbc9c ("tap: use build_skb() for small packet")
Signed-off-by: NAlexis Bauvin <abauvin@scaleway.com>
Acked-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While using net_dim, a dim_sample was used without ever initializing the
comps value. Added use of DIV_ROUND_DOWN_ULL() to prevent potential
overflow, it should not be a problem to save the final result in an int
because after the division by epms the value should not be larger than a
few thousand.

[ 1040.127124] UBSAN: Undefined behaviour in lib/dim/dim.c:78:23
[ 1040.130118] signed integer overflow:
[ 1040.131643] 134718714 * 100 cannot be represented in type 'int'

Fixes: 398c2b05 ("linux/dim: Add completions count to dim_sample")
Signed-off-by: NYamin Friedman <yaminf@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The memory allocated for the stats array may contain arbitrary data.

Fixes: e4f9ba64 ("net: phy: mscc: add support for VSC8514 PHY.")
Fixes: 00d70d8e ("net: phy: mscc: add support for VSC8574 PHY")
Fixes: a5afc167 ("net: phy: mscc: add support for VSC8584 PHY")
Fixes: f76178dc ("net: phy: mscc: add ethtool statistics counters")
Signed-off-by: NAndreas Schwab <schwab@suse.de>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SFP modules connected using the SGMII interface have their own PHYs which
are handled by the struct phylink's phydev field. On the other hand, for
the modules connected using 1000Base-X interface that field is not set.

Since commit ce0aa27f ("sfp: add sfp-bus to bridge between network
devices and sfp cages") phylink_start() ends up setting the phydev field
using the sfp-bus infrastructure, which eventually calls phy_start() on it,
and then calling phy_start() again on the same phydev from phylink_start()
itself. Similar call sequence holds for phylink_stop(), only in the reverse
order. This results in WARNs during network interface bringup and shutdown
when a copper SFP module is connected, as phy_start() and phy_stop() are
called twice in a row for the same phy_device:

  % ip link set up dev eth0
  ------------[ cut here ]------------
  called from state UP
  WARNING: CPU: 1 PID: 155 at drivers/net/phy/phy.c:895 phy_start+0x74/0xc0
  Modules linked in:
  CPU: 1 PID: 155 Comm: backend Not tainted 5.2.0+ #1
  NIP:  c0227bf0 LR: c0227bf0 CTR: c004d224
  REGS: df547720 TRAP: 0700   Not tainted  (5.2.0+)
  MSR:  00029000 <CE,EE,ME>  CR: 24002822  XER: 00000000

  GPR00: c0227bf0 df5477d8 df5d7080 00000014 df9d2370 df9d5ac4 1f4eb000 00000001
  GPR08: c061fe58 00000000 00000000 df5477d8 0000003c 100c8768 00000000 00000000
  GPR16: df486a00 c046f1c8 c046eea0 00000000 c046e904 c0239604 db68449c 00000000
  GPR24: e9083204 00000000 00000001 db684460 e9083404 00000000 db6dce00 db6dcc00
  NIP [c0227bf0] phy_start+0x74/0xc0
  LR [c0227bf0] phy_start+0x74/0xc0
  Call Trace:
  [df5477d8] [c0227bf0] phy_start+0x74/0xc0 (unreliable)
  [df5477e8] [c023cad0] startup_gfar+0x398/0x3f4
  [df547828] [c023cf08] gfar_enet_open+0x364/0x374
  [df547898] [c029d870] __dev_open+0xe4/0x140
  [df5478c8] [c029db70] __dev_change_flags+0xf0/0x188
  [df5478f8] [c029dc28] dev_change_flags+0x20/0x54
  [df547918] [c02ae304] do_setlink+0x310/0x818
  [df547a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0
  [df547c28] [c02b222c] rtnl_newlink+0x48/0x68
  [df547c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c
  [df547c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0
  [df547cd8] [c02cba3c] netlink_unicast+0x114/0x19c
  [df547d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0
  [df547d58] [c027b668] sock_sendmsg_nosec+0x20/0x40
  [df547d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc
  [df547e98] [c027df7c] __sys_sendmsg+0x68/0x84
  [df547ef8] [c027e430] sys_socketcall+0x1a0/0x204
  [df547f38] [c000d1d8] ret_from_syscall+0x0/0x38
  --- interrupt: c01 at 0xfd4e030
      LR = 0xfd4e010
  Instruction dump:
  813f0188 38800000 2b890005 419d0014 3d40c046 5529103a 394aa208 7c8a482e
  3c60c046 3863a1b8 4cc63182 4be009a1 <0fe00000> 48000030 3c60c046 3863a1d0
  ---[ end trace d4c095aeaf6ea998 ]---

and

  % ip link set down dev eth0
  ------------[ cut here ]------------
  called from state HALTED
  WARNING: CPU: 1 PID: 184 at drivers/net/phy/phy.c:858 phy_stop+0x3c/0x88

  <...>

  Call Trace:
  [df581788] [c0228450] phy_stop+0x3c/0x88 (unreliable)
  [df581798] [c022d548] sfp_sm_phy_detach+0x1c/0x44
  [df5817a8] [c022e8cc] sfp_sm_event+0x4b0/0x87c
  [df581848] [c022f04c] sfp_upstream_stop+0x34/0x44
  [df581858] [c0225608] phylink_stop+0x7c/0xe4
  [df581868] [c023c57c] stop_gfar+0x7c/0x94
  [df581888] [c023c5b8] gfar_close+0x24/0x94
  [df5818a8] [c0298688] __dev_close_many+0xdc/0xf8
  [df5818c8] [c029db58] __dev_change_flags+0xd8/0x188
  [df5818f8] [c029dc28] dev_change_flags+0x20/0x54
  [df581918] [c02ae304] do_setlink+0x310/0x818
  [df581a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0
  [df581c28] [c02b222c] rtnl_newlink+0x48/0x68
  [df581c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c
  [df581c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0
  [df581cd8] [c02cba3c] netlink_unicast+0x114/0x19c
  [df581d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0
  [df581d58] [c027b668] sock_sendmsg_nosec+0x20/0x40
  [df581d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc
  [df581e98] [c027df7c] __sys_sendmsg+0x68/0x84
  [df581ef8] [c027e430] sys_socketcall+0x1a0/0x204
  [df581f38] [c000d1d8] ret_from_syscall+0x0/0x38

  <...>

  ---[ end trace d4c095aeaf6ea999 ]---

SFP modules with the 1000Base-X interface are not affected.

Place explicit calls to phy_start() and phy_stop() before enabling or after
disabling an attached SFP module, where phydev is not yet set (or is
already unset), so they will be made only from the inside of sfp-bus, if
needed.

Fixes: 21796261 ("net: phy: warn if phy_start is called from invalid state")
Signed-off-by: NArseny Solokha <asolokha@kb.kras.ru>
Acked-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When closing the CAN device while tx skbs are inflight, echo skb could
be released twice. By calling close_candev() before unlinking all
pending tx urbs, then the internal echo_skb[] array is fully and
correctly cleared before the USB write callback and, therefore,
can_get_echo_skb() are called, for each aborted URB.

Fixes: bb478555 ("can: usb: PEAK-System Technik USB adapters driver core")
Signed-off-by: NStephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

To enter stop mode, the CPU should manually assert a global Stop Mode
request and check the acknowledgment asserted by FlexCAN. The CPU must
only consider the FlexCAN in stop mode when both request and
acknowledgment conditions are satisfied.

Fixes: de3578c1 ("can: flexcan: add self wakeup support")
Reported-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The gpr_np variable is still being used in dev_dbg() after the
of_node_put() call, which may result in use-after-free.

Fixes: de3578c1 ("can: flexcan: add self wakeup support")
Signed-off-by: NWen Yang <wen.yang99@zte.com.cn>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

add error check when workqueue alloc failed, and remove redundant code
to make it clear.

Fixes: e0000163 ("can: Driver for the Microchip MCP251x SPI CAN controllers")
Signed-off-by: NWeitao Hou <houweitaoo@gmail.com>
Acked-by: NWillem de Bruijn <willemb@google.com>
Tested-by: NSean Nyekjaer <sean@geanix.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

We have observed rcar_canfd driver entering IRQ storm under high load,
with following scenario:
- rcar_canfd_global_interrupt() in entered due to Rx available,
- napi_schedule_prep() is called, and sets NAPIF_STATE_SCHED in state
- Rx fifo interrupts are masked,
- rcar_canfd_global_interrupt() is entered again, this time due to
  error interrupt (e.g. due to overflow),
- since scheduled napi poller has not yet executed, condition for calling
  napi_schedule_prep() from rcar_canfd_global_interrupt() remains true,
  thus napi_schedule_prep() gets called and sets NAPIF_STATE_MISSED flag
  in state,
- later, napi poller function rcar_canfd_rx_poll() gets executed, and
  calls napi_complete_done(),
- due to NAPIF_STATE_MISSED flag in state, this call does not clear
  NAPIF_STATE_SCHED flag from state,
- on return from napi_complete_done(), rcar_canfd_rx_poll() unmasks Rx
  interrutps,
- Rx interrupt happens, rcar_canfd_global_interrupt() gets called
  and calls napi_schedule_prep(),
- since NAPIF_STATE_SCHED is set in state at this time, this call
  returns false,
- due to that false return, rcar_canfd_global_interrupt() returns
  without masking Rx interrupt
- and this results into IRQ storm: unmasked Rx interrupt happens again
  and again is misprocessed in the same way.

This patch fixes that scenario by unmasking Rx interrupts only when
napi_complete_done() returns true, which means it has cleared
NAPIF_STATE_SCHED in state.

Fixes: dd3bd23e ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
Signed-off-by: NNikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

CONFIG_CAN_LEDS is deprecated. When trying to use the generic netdev
trigger as suggested, there's a small inconsistency with the link
property: The LED is on initially, stays on when the device is brought
up, and then turns off (as expected) when the device is brought down.

Make sure the LED always reflects the state of the CAN device.
Signed-off-by: NRasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Replace the custom implementation with fwnode_get_mac_address,
which works on both DT and ACPI platforms.

While here, replace memcpy() by ether_addr_copy().
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The onboard sky2 NIC on ASUS P6T WS PRO doesn't work after PM resume
due to the infamous IRQ problem.  Disabling MSI works around it, so
let's add it to the blacklist.

Unfortunately the BIOS on the machine doesn't fill the standard
DMI_SYS_* entry, so we pick up DMI_BOARD_* entries instead.

BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1142496Reported-and-tested-by: NMarcus Seyfarth <m.seyfarth@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: NNishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return.
Issue found with Coccinelle.
Signed-off-by: NNishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit f4e5f775.

Andrew Lunn says this should be handled another way.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some glue logic drivers support 1G without having GMAC/GMAC4/XGMAC.

Let's allow this speed by default.
Reported-by: NOndrej Jirman <megi@xff.cz>
Tested-by: NOndrej Jirman <megi@xff.cz>
Fixes: 5b0d7d7d ("net: stmmac: Add the missing speeds that XGMAC supports")
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need the memory to be zeroed upon allocation so use kcalloc()
instead.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RX Descriptors are being cleaned after setting the buffers which may
lead to buffer addresses being wiped out.

Fix this by clearing earlier the RX Descriptors.

Fixes: 2af6106a ("net: stmmac: Introducing support for Page Pool")
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit(net: phy: marvell: change default m88e1510 LED configuration),
the active LED of Hip07 devices is always off, because Hip07 just
use 2 LEDs.
This patch adds a phy_register_fixup_for_uid() for m88e1510 to
correct the LED configuration.

Fixes: 07777246 ("net: phy: marvell: change default m88e1510 LED configuration")
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Reviewed-by: Nlinyunsheng <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PPv2's XLGMAC can wait for 3 idle frames before triggering a link up
event. This can cause the link to be stuck low when there's traffic on
the interface, so disable this feature.

Fixes: 4bb04326 ("net: mvpp2: phylink support")
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following scenario was encountered during testing of logical
partition mobility on pseries partitions with bonded ibmvnic
adapters in LACP mode.

1. Driver receives a signal that the device has been
   swapped, and it needs to reset to initialize the new
   device.

2. Driver reports loss of carrier and begins initialization.

3. Bonding driver receives NETDEV_CHANGE notifier and checks
   the slave's current speed and duplex settings. Because these
   are unknown at the time, the bond sets its link state to
   BOND_LINK_FAIL and handles the speed update, clearing
   AD_PORT_LACP_ENABLE.

4. Driver finishes recovery and reports that the carrier is on.

5. Bond receives a new notification and checks the speed again.
   The speeds are valid but miimon has not altered the link
   state yet.  AD_PORT_LACP_ENABLE remains off.

Because the slave's link state is still BOND_LINK_FAIL,
no further port checks are made when it recovers. Though
the slave devices are operational and have valid speed
and duplex settings, the bond will not send LACPDU's. The
simplest fix I can see is to force another speed check
in bond_miimon_commit. This way the bond will update
AD_PORT_LACP_ENABLE if needed when transitioning from
BOND_LINK_FAIL to BOND_LINK_UP.

CC: Jarod Wilson <jarod@redhat.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NThomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is an extra rcu_read_unlock left in netvsc_recv_callback(),
after a previous patch that removes RCU from this function.
This patch removes the extra RCU unlock.

Fixes: 345ac089 ("hv_netvsc: pass netvsc_device to receive callback")
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vrf_process_v4_outbound() and vrf_process_v6_outbound() do routing
using ip/ipv6 addresses, but don't make sure the header is available
in skb->data[] (skb_headlen() is less then header size).

Case:

1) igb driver from intel.
2) Packet size is greater then 255.
3) MPLS forwards to VRF device.

So, patch adds pskb_may_pull() calls in vrf_process_v4/v6_outbound()
functions.
Signed-off-by: NPeter Kosyh <p.kosyh@gmail.com>
Reviewed-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 8c0d3a02 ("PCI: Add accessors for PCI Express Capability")
added accessors for the PCI Express Capability so that drivers didn't
need to be aware of differences between v1 and v2 of the PCI
Express Capability.

Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: NFrederick Lawler <fred@fredlawl.com>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 8c0d3a02 ("PCI: Add accessors for PCI Express Capability")
added accessors for the PCI Express Capability so that drivers didn't
need to be aware of differences between v1 and v2 of the PCI
Express Capability.

Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: NFrederick Lawler <fred@fredlawl.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 8c0d3a02 ("PCI: Add accessors for PCI Express Capability")
added accessors for the PCI Express Capability so that drivers didn't
need to be aware of differences between v1 and v2 of the PCI
Express Capability.

Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: NFrederick Lawler <fred@fredlawl.com>
Reviewed-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As pointed out by Firo Yang, a netdev tx timeout may trigger just before an
ethtool set_channels operation is started. be_tx_timeout(), which dumps
some queue structures, is not written to run concurrently with
be_update_queues(), which frees/allocates those queues structures. Add some
synchronization between the two.

Message-id: <CH2PR18MB31898E033896F9760D36BFF288C90@CH2PR18MB3189.namprd18.prod.outlook.com>
Signed-off-by: NBenjamin Poirier <bpoirier@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>