v2:	add couple missing conversions in drivers
	split unexporting netdev_fix_features()
	implemented %pNF
	convert sock::sk_route_(no?)caps
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

replace it by ndo_set_rx_mode
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The reset loop check should check the MII_BMCR register value for
BMCR_RESET rather than for MII_BMCR (the register address, which also
happens to be zero).
Signed-off-by: NRabin Vincent <rabin@rab.in>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This makes sure that when a driver calls the ethtool's
get/set_settings() callback of another driver, the data passed to it
is clean. This guarantees that speed_hi will be zeroed correctly if
the called callback doesn't explicitely set it: we are sure we don't
get a corrupted speed from the underlying driver. We also take care of
setting the cmd field appropriately (ETHTOOL_GSET/SSET).

This applies to dev_ethtool_get_settings(), which now makes sure it
sets up that ethtool command parameter correctly before passing it to
drivers. This also means that whoever calls dev_ethtool_get_settings()
does not have to clean the ethtool command parameter. This function
also becomes an exported symbol instead of an inline.

All drivers visible to make allyesconfig under x86_64 have been
updated.
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for SMSC's LAN9530, LAN9730 and LAN89530 USB
ethernet controllers to the existing smsc95xx driver by adding
their new USB VID/PID pairs.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's a race (not fixed here) in smsc75xx in setting RFE_CTL that's not
properly handled via rfe_ctl_lock. Spinlock is not a good tool here, as
this has to wait for URB completion (or maybe just submission) after issuing
register write request. Otherwise, the rfe_ctl might be changed just after
spin_unlock() and device left programmed with other value.

smsc95xx has increased hard_header_len for the case of TX checksumming.

smsc75xx is fixed to advertise IP+IPV6_CSUM instead of HW_CSUM as it does
not use csum_start/csum_offset.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The set_multicast operation performs asynchronous writes to the
device, with some addresses pointing to the stack. Bad things may
happen, and this is trapped CONFIG_DMA_API_DEBUG:

[    5.237762] WARNING: at /build/buildd/linux-linaro-omap-2.6.38/lib/dma-debug.c:867 check_for_stack+0xd4/0x100()
[    5.237792] ehci-omap ehci-omap.0: DMA-API: device driver maps memory fromstack [addr=d9c77dec]
[    5.237792] Modules linked in: smsc95xx(+) usbnet twl6030_usb twl4030_pwrbutton leds_gpio omap_wdt omap2_mcspi
[    5.237854] [<c006d618>] (unwind_backtrace+0x0/0xf8) from [<c00a6a14>] (warn_slowpath_common+0x54/0x64)
[    5.237884] [<c00a6a14>] (warn_slowpath_common+0x54/0x64) from [<c00a6ab8>] (warn_slowpath_fmt+0x30/0x40)
[    5.237915] [<c00a6ab8>] (warn_slowpath_fmt+0x30/0x40) from [<c034e9d8>] (check_for_stack+0xd4/0x100)
[    5.237915] [<c034e9d8>] (check_for_stack+0xd4/0x100) from [<c034fea8>] (debug_dma_map_page+0xb4/0xdc)
[    5.237976] [<c034fea8>] (debug_dma_map_page+0xb4/0xdc) from [<c04242f0>] (map_urb_for_dma+0x26c/0x304)
[    5.237976] [<c04242f0>] (map_urb_for_dma+0x26c/0x304) from [<c0424594>] (usb_hcd_submit_urb+0x78/0x19c)
[    5.238037] [<c0424594>] (usb_hcd_submit_urb+0x78/0x19c) from [<bf049c5c>] (smsc95xx_write_reg_async+0xb4/0x130 [smsc95xx])
[    5.238067] [<bf049c5c>] (smsc95xx_write_reg_async+0xb4/0x130 [smsc95xx]) from [<bf049dd4>] (smsc95xx_set_multicast+0xfc/0x148 [smsc95xx])
[    5.238098] [<bf049dd4>] (smsc95xx_set_multicast+0xfc/0x148 [smsc95xx]) from [<bf04a118>] (smsc95xx_reset+0x2f8/0x68c [smsc95xx])
[    5.238128] [<bf04a118>] (smsc95xx_reset+0x2f8/0x68c [smsc95xx]) from [<bf04a8cc>] (smsc95xx_bind+0xcc/0x188 [smsc95xx])
[    5.238159] [<bf04a8cc>] (smsc95xx_bind+0xcc/0x188 [smsc95xx]) from [<bf03ef1c>] (usbnet_probe+0x204/0x4c4 [usbnet])
[    5.238220] [<bf03ef1c>] (usbnet_probe+0x204/0x4c4 [usbnet]) from [<c0429078>] (usb_probe_interface+0xe4/0x1c4)
[    5.238250] [<c0429078>] (usb_probe_interface+0xe4/0x1c4) from [<c03a8770>] (really_probe+0x64/0x160)
[    5.238250] [<c03a8770>] (really_probe+0x64/0x160) from [<c03a8a30>] (driver_probe_device+0x48/0x60)
[    5.238281] [<c03a8a30>] (driver_probe_device+0x48/0x60) from [<c03a8ad4>] (__driver_attach+0x8c/0x90)
[    5.238311] [<c03a8ad4>] (__driver_attach+0x8c/0x90) from [<c03a7b24>] (bus_for_each_dev+0x50/0x7c)
[    5.238311] [<c03a7b24>] (bus_for_each_dev+0x50/0x7c) from [<c03a82ec>] (bus_add_driver+0x190/0x250)
[    5.238311] [<c03a82ec>] (bus_add_driver+0x190/0x250) from [<c03a8cf8>] (driver_register+0x78/0x13c)
[    5.238433] [<c03a8cf8>] (driver_register+0x78/0x13c) from [<c0428040>] (usb_register_driver+0x78/0x13c)
[    5.238464] [<c0428040>] (usb_register_driver+0x78/0x13c) from [<c005b680>] (do_one_initcall+0x34/0x188)
[    5.238494] [<c005b680>] (do_one_initcall+0x34/0x188) from [<c00e11f0>] (sys_init_module+0xb0/0x1c0)
[    5.238525] [<c00e11f0>] (sys_init_module+0xb0/0x1c0) from [<c0065c40>] (ret_fast_syscall+0x0/0x30)

Move the two offenders to the private structure which is kmalloc-ed,
and thus safe.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace skb->csum_start - skb_headroom(skb) with skb_checksum_start_offset().

Note for usb/smsc95xx: skb->data - skb->head == skb_headroom(skb).
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The smsc95xx driver currently generates a new random MAC address
every time the interface is brought up. This makes it impossible to
override using the standard `ifconfig hw ether` approach.

Past patches tried to make the MAC address a module parameter or
base it off the die ID, but it seems to me much simpler (and
hopefully less controversial) to stick with the current random
generation scheme, but allow the user to change the address.

This patch does exactly that - it moves the random address
generation from smsc95xx_reset() into smsc95xx_bind(), so that it is
done once on module load, not on every ifup. The user can then
override this using the standard mechanisms.

Applies against 2.6.35 and linux-2.6 head.
Signed-off-by: NBernard Blackham <b-omap@largestprime.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Converts the list and the core manipulating with it to be the same as uc_list.

+uses two functions for adding/removing mc address (normal and "global"
 variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
 manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

TX checksum offload does not work properly when transmitting
UDP packets with 0, 1 or 2 bytes of data.  This patch works
around the problem by calculating checksums for these packets
in the driver.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch ensures the PHY correctly completes its reset before
setting register values.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

also removed needless checks in smsc95xx
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert from:
	if (netif_msg_<foo>(priv))
		dev_<level>(dev...
to
	netif_<level>(priv, foo, dev...

Also convert a few:

	if (i < REG_TIMEOUT) {
		etc...
		return ret;
       }
to
	if (i >= REG_TIMEOUT)
		goto fail;
	etc...
	return ret;
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These macros are too similar to the dev_<level> equivalents
but take a usbnet * argument.  Convert them to the recently
introduced netdev_<level> macros and remove the old macros.

The old macros had "\n" appended to the format string.
Add the "\n" to the converted uses.

Some existing uses of the dev<foo> macros in cdc_eem.c
probably mistakenly had trailing "\n".  No "\n" added there.

Fix net1080 this/other log message inversion.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.

Jirka
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.
Signed-off-by: NAndré Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Usbnet framework assumes USB hardware doesn't handle zero length
packets, but SMSC LAN95xx requires these to be sent for correct
operation.

This patch fixes an easily reproducible tx lockup when sending a frame
that results in exactly 512 bytes in a USB transmission (e.g. a UDP
frame with 458 data bytes, due to IP headers and our USB headers).  It
adds an extra flag to usbnet for the hardware driver to indicate that
it can handle and requires the zero length packets.

This patch should not affect other usbnet users, please also consider
for -stable.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No need to put ethtool_ops in data, they should be const.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The eeprom read & write commands currently check the E2P_CMD_LOADED_ bit is
set before allowing any operations.  This prevents any reading or writing
unless a correctly programmed EEPROM is installed.

This patch removes the check, so it is possible to program blank EEPROMS
via ethtool.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The smsc95xx driver was forwarding the trailing fcs on received frames
up the stack leading to confusion in tcpdump.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Tested-by: NSteve Glendinning <steve.glendinning@smsc.com>
Acked-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LAN9512 and LAN9514 are USB hubs with an integrated 10/100 ethernet
controller.  Logically this looks like an ethernet controller (similar
to LAN9500) permanently attached to one of the hub's downstream ports.

This patch adds the usb device id of the new ethernet controller to the
smsc95xx driver.  This id is the same in both new devices.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SMSC LAN9500 has dual purpose GPIO/LED pins, and by default at power-on
these are configured as GPIOs.  This means that if LEDs are fitted they
won't ever light.

This patch sets them to be LED outputs for speed, duplex and
link/activity.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Impact: Make symbols static.

Fix this sparse warnings:
  drivers/net/usb/hso.c:1249:6: warning: symbol 'hso_unthrottle_tasklet' was not declared. Should it be static?
  drivers/net/usb/hso.c:1268:6: warning: symbol 'hso_unthrottle_workfunc' was not declared. Should it be static?
  drivers/net/usb/hso.c:1466:5: warning: symbol 'tiocmget_submit_urb' was not declared. Should it be static?
  drivers/net/usb/smsc95xx.c:62:5: warning: symbol 'turbo_mode' was not declared. Should it be static?
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

smsc95xx_async_cmd_callback doesn't currently match usb_complete_t, so
there's a cast to force the square peg into the round hole.  This patch
fixes this properly.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Oliver Neukum spotted the useless complete() in our async callback.  On
closer inspection, the entire completion struct is unused.  This patch
removes it.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

USB is going to switch the signature of the callbacks to
void callback(struct urb *urb, int status)
This patch will ease the transition.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These 4 drivers have identical full duplex flow control resolution
functions.  This patch changes them all to use one common function.

The function in question decides whether a device should enable TX and
RX flow control in a standard way (IEEE 802.3-2005 table 28B-3), so this
should also be useful for other drivers.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

flags used within drivers for indicating tx and rx flow control are
defined in 4 drivers (and probably more), move these constants to mii.h.

The 3 SMSC drivers use the same constants (FLOW_CTRL_TX), but TG3 uses
TG3_FLOW_CTRL_TX, so this patch also renames the constants within TG3.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LAN9500 supports tx checksum offload, which slightly decreases cpu
utilisation.  The benefit isn't very large because we still require
the skb to be linearized, but it does save a few cycles.

This patch adds support for it, and enables it by default.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.

I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix warnings caught by David Miller on sparc64
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Attached is a driver for SMSC's LAN9500 USB2.0 10/100 ethernet
adapter.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>