Even before channel contexts/multi-channel, having a
single global TX power limit was already problematic,
in particular if two managed interfaces connected to
two APs with different power constraints. The channel
context introduction completely broke this though and
in fact I had disabled TX power configuration there
for drivers using channel contexts.

Change everything to track TX power per interface so
that different user settings and different channel
maxima are treated correctly. Also continue tracking
the global TX power though for compatibility with
applications that attempt to configure the wiphy's
TX power globally.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since cfg80211 will now call the explicit stop_ap
operation when an AP interface goes down, move all
teardown code there and remove it from interface
handling. The only thing that needs to stay is the
code to dev_close() all dependent VLANs.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch prepares mac80211 for a later implementation of mesh or
ad-hoc powersave clients.
The structures related to powersave (buffer, TIM map, counters) are
moved from the AP-specific interface structure to a generic structure
that can be embedded into any interface type.
The functions related to powersave are prepared to allow easy
extension with different interface types. For example with:

+ } else if (sta->sdata->vif.type == NL80211_IFTYPE_MESH_POINT) {
+         ps = &sdata->u.mesh.ps;

Some references to the AP's beacon structure are removed where they
were obviously not used.

The patch compiles without warning and has been briefly tested as AP
interface with one client in PS mode.
Signed-off-by: NMarco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

On each channel that the device is operating on, it
may need to listen using one or more chains depending
on the SMPS settings of the interfaces using it. The
previous channel context changes completely removed
this ability (before, it was available as the SMPS
mode).

Add per-context tracking of the required static and
dynamic RX chains and notify the driver on changes.
To achieve this, track the chains and SMPS mode used
on each virtual interface and update the channel
context whenever this changes.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of operating on a single channel only,
use the new channel context infrastructure in
all mac80211 code.

This enables drivers that want to use the new
channel context infrastructure to use multiple
channels, while nothing should change for all
the other drivers that don't support it.

Right now this disables both TX power settings
and spatial multiplexing powersave. Both need
to be re-enabled on a channel context basis.

Additionally, when channel contexts are used
drop the connection when channel switch is
received rather than trying to handle it. This
will have to be improved later.

[With fixes from Eliad and Emmanuel incorporated]
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Free tx status skbs when draining power save buffers, pending frames, or
when tearing down a vif.
Fixes remaining conditions that can lead to hostapd/wpa_supplicant hangs when
running out of socket write memory.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 calls synchronize_rcu() on sta deletion,
which increase the roaming time significantly.

Convert it into a call_rcu() mechanism, in order
to avoid blocking. Since some of the cleanup
functions might sleep, schedule from the call_rcu
callback a new work that will do the actual cleanup.

In order to make sure the cleanup occurs before
the interface went down, flush local->workqueue
on ieee80211_do_stop().
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A P2P Device interface does not have a netdev, and is not
expected to be used for transmitting data, so there is no
need to assign hw queues for it.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some devices like the current iwlwifi implementation
require that the P2P interface address match the P2P
Device address (only one P2P interface is supported.)
Add the HW flag IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF
that allows drivers to request that P2P Interfaces
added while a P2P Device is active get the same MAC
address by default.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

After cfg80211 got a P2P Device abstraction, add
support to mac80211. Whether it really is supported
or not will depend on whether or not the driver has
support for it, but mac80211 needs to change to be
able to support drivers that need a P2P Device.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to support using a different MAC address
for the P2P Device address we must first have a
P2P Device abstraction that can be assigned a MAC
address.

This abstraction will also be useful to support
offloading P2P operations to the device, e.g.
periodic listen for discoverability.

Currently, the driver is responsible for assigning
a MAC address to the P2P Device, but this could be
changed by allowing a MAC address to be given to
the NEW_INTERFACE command.

As it has no associated netdev, a P2P Device can
only be identified by its wdev identifier but the
previous patches allowed using the wdev identifier
in various APIs, e.g. remain-on-channel.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This could take a while (100ms+) and may delay sending assoc resp
in AP mode with WPS or P2P GO (as setting the probe resp takes place
there). We've encountered situations where the delay was big enough
to cause connection problems with devices like Galaxy Nexus.
Switch to using call_rcu with a free handler.

[Arik - rework to use plain buffer and instead of skb]
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This function was only used by mesh, and not really needed since any
interface-specific cleanup already happens in the netdev handlers.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

It is not necessary to stop the mesh beacon in the mac80211 ndo_stop
handler, since cfg80211 has already left the mesh on NETDEV_GOING_DOWN
notification.

Also some improvements to ieee80211_stop_mesh():

 - flush mpath entries.
 - flush sta entries per-sdata so we don't remove entries belonging to
   other vifs on the same hw.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Enable the carrier on WDS type interfaces only
after having added the station entry for the
WDS peer so outgoing frames will find it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of assuming the carrier is on all
the time in mesh manage it with joining
and leaving the mesh.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Using hw.conf.channel is wrong as it could be the
temporary channel if any function like the beacon
get function is called while scanning or during
other temporary out-of-channel activities.

Use oper_channel instead.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This reverts commit 870d37fc.

This code doesn't work as cfg80211 will call
set_monitor_enabled at the wrong time and it
doesn't seem to be possible to fix this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the virtual monitor interface is requested
by the driver, it should also be iterated over
when the driver wants to iterate all active
interfaces.

To allow that protect it with the iflist_mtx.

Change-Id: I58ac5de2f4ce93d12c5a98ecd2859f60158d5d69
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Making the scan_sdata pointer usable with RCU makes
it possible to dereference it in the RX path to see
if a received frame actually matches the interface
that is scanning. This is just preparations, making
the pointer __rcu.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to be able to create P2P Device wdevs, move
the virtual interface management over to wireless_dev
structures.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use cfg80211 the new .set_monitor_enabled instead
of tracking it inside mac80211.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since it's not called from any file outside where
it's defined, the function can be static if moved
up in the file before the callers.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

ieee80211_check_concurrent_iface() need not use the
netdev. Remove the use of the netdev here to prepare
the function for P2P device addition.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
 * a lot of messages should be pr_info, not pr_debug
 * wholesale use of pr_debug makes it require *both*
   Kconfig and dynamic configuration
 * there are still a lot of ifdefs
 * the style is very inconsistent, sometimes the
   sdata->name is printed in front

Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Save and configure the wmm_acm per sdata, rather than
per hardware.

If wmm_acm is saved per hardware when running two
interfaces simultaneously on the same hardware one
interface's wmm policy will be affected by the other
interface.
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Redesign all the off-channel code, getting rid of
the generic off-channel work concept, replacing
it with a simple remain-on-channel list.

This fixes a number of small issues with the ROC
implementation:
 * offloaded remain-on-channel couldn't be queued,
   now we can queue it as well, if needed
 * in iwlwifi (the only user) offloaded ROC is
   mutually exclusive with scanning, use the new
   queue to handle that case -- I expect that it
   will later depend on a HW flag

The bigger issue though is that there's a bad bug
in the current implementation: if we get a mgmt
TX request while HW roc is active, and this new
request has a wait time, we actually schedule a
software ROC instead since we can't guarantee the
existing offloaded ROC will still be that long.
To fix this, the queuing mechanism was needed.

The queuing mechanism for offloaded ROC isn't yet
optimal, ideally we should add API to have the HW
extend the ROC if needed. We could add that later
but for now use a software implementation.

Overall, this unifies the behaviour between the
offloaded and software-implemented case as much
as possible.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The IDLE handling in HW off-channel is broken right
now since we turn off IDLE only when the off-channel
period already started. Therefore, all drivers that
use it today (only iwlwifi!) must support off-channel
while idle, so playing with idle isn't needed at all.

Off-channel in general, since it's no longer used for
authentication/association, shouldn't affect PS, so
also remove that logic.

Also document a small caveat for reporting TX status
from off-channel frames in HW remain-on-channel.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Standardize the debugging to be able to use dynamic_debug.

Coalesce formats, align arguments.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Low level drivers can now set certain netdev feature bits in
netdev_features member of the ieee80211_hw struct. These will be
propagated to every netdev created from this HW.

The white-listed features currently include only ones related to HW
checksumming.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When any interface goes down, it could be the one that we
were doing a remain-on-channel with. We therefore need to
cancel the remain-on-channel and flush the related work
structs so they don't run after the interface has been
removed or even destroyed.

It's also possible in this case that an off-channel SKB
was never transmitted, so free it if this is the case.
Note that this can also happen if the driver finishes
the off-channel period without ever starting it.

Cc: stable@kernel.org
Reported-by: NNirav Shah <nirav.j2.shah@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

My queue management rework broke drivers that don't
have multiple AC queues and register a single queue
only, causing a warning:

WARNING: at net/mac80211/iface.c:162 ieee80211_check_queues

This was due to filling the queues wrongly and then
noticing the error when checking later.
Reported-and-Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.

Done via cocci script:

$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
-	!compare_ether_addr(a, b)
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	compare_ether_addr(a, b)
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) == 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) != 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) == 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) != 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!!ether_addr_equal(a, b)
+	ether_addr_equal(a, b)
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds hepler to clean sdata ieee80211_clean_sdata similar way as
ieee80211_setup_sdata is implemented. The function will be used by other
interfaces later.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ieee80211_mgd_teardown() is called on netdev removal, which
occurs after the vif was already removed from the low-level
driver, resulting in the following warning:

[ 4809.014734] ------------[ cut here ]------------
[ 4809.019861] WARNING: at net/mac80211/driver-ops.h:12 ieee80211_bss_info_change_notify+0x200/0x2c8 [mac80211]()
[ 4809.030388] wlan0:  Failed check-sdata-in-driver check, flags: 0x4
[ 4809.036862] Modules linked in: wlcore_sdio(-) wl12xx wlcore mac80211 cfg80211 [last unloaded: cfg80211]
[ 4809.046849] [<c001bd4c>] (unwind_backtrace+0x0/0x12c)
[ 4809.055937] [<c047cf1c>] (dump_stack+0x20/0x24)
[ 4809.065385] [<c003e334>] (warn_slowpath_common+0x5c/0x74)
[ 4809.075589] [<c003e408>] (warn_slowpath_fmt+0x40/0x48)
[ 4809.088291] [<bf033630>] (ieee80211_bss_info_change_notify+0x200/0x2c8 [mac80211])
[ 4809.102844] [<bf067f84>] (ieee80211_destroy_auth_data+0x80/0xa4 [mac80211])
[ 4809.116276] [<bf068004>] (ieee80211_mgd_teardown+0x5c/0x74 [mac80211])
[ 4809.129331] [<bf043f18>] (ieee80211_teardown_sdata+0xb0/0xd8 [mac80211])
[ 4809.141595] [<c03b5e58>] (rollback_registered_many+0x228/0x2f0)
[ 4809.153056] [<c03b5f48>] (unregister_netdevice_many+0x28/0x50)
[ 4809.165696] [<bf041ea8>] (ieee80211_remove_interfaces+0xb4/0xdc [mac80211])
[ 4809.179151] [<bf032174>] (ieee80211_unregister_hw+0x50/0xf0 [mac80211])
[ 4809.191043] [<bf0bebb4>] (wlcore_remove+0x5c/0x7c [wlcore])
[ 4809.201491] [<c02c6918>] (platform_drv_remove+0x24/0x28)
[ 4809.212029] [<c02c4d50>] (__device_release_driver+0x8c/0xcc)
[ 4809.222738] [<c02c4e84>] (device_release_driver+0x30/0x3c)
[ 4809.233099] [<c02c4258>] (bus_remove_device+0x10c/0x128)
[ 4809.242620] [<c02c26f8>] (device_del+0x11c/0x17c)
[ 4809.252150] [<c02c6de0>] (platform_device_del+0x28/0x68)
[ 4809.263051] [<bf0df49c>] (wl1271_remove+0x3c/0x50 [wlcore_sdio])
[ 4809.273590] [<c03806b0>] (sdio_bus_remove+0x48/0xf8)
[ 4809.283754] [<c02c4d50>] (__device_release_driver+0x8c/0xcc)
[ 4809.293729] [<c02c4e2c>] (driver_detach+0x9c/0xc4)
[ 4809.303163] [<c02c3d7c>] (bus_remove_driver+0xc4/0xf4)
[ 4809.312973] [<c02c5a98>] (driver_unregister+0x70/0x7c)
[ 4809.323220] [<c03809c4>] (sdio_unregister_driver+0x24/0x2c)
[ 4809.334213] [<bf0df458>] (wl1271_exit+0x14/0x1c [wlcore_sdio])
[ 4809.344930] [<c009b1a4>] (sys_delete_module+0x228/0x2a8)
[ 4809.354734] ---[ end trace 515290ccf5feb522 ]---

Rename ieee80211_mgd_teardown() to ieee80211_mgd_stop(),
and call it on ieee80211_do_stop().
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit 3a25a8c8 (mac80211: add improved HW queue control) introduced a
bug when running in AP mode without the IEEE80211_HW_QUEUE_CONTROL
flag set.  The ieee80211_check_queues() function always returns
-EINVAL, preventing AP mode from starting.  To fix this, check whether
this flag is set before checking if cab_queue is set properly.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Eliad's comment prompted me to look closer at
the error paths in ieee80211_do_open() and I
found one that should use the error labels.

Also add a comment about the clear_bit since
in many error cases the bit hasn't been set.

Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 currently only supports one hardware queue
per AC. This is already problematic for off-channel
uses since if we go off channel while the BE queue
is full and then try to send an off-channel frame
the frame will never go out. This will become worse
when we support multi-channel since then a queue on
one channel might be full, but we have to stop the
software queue for all channels. That is obviously
not desirable.

To address this problem allow drivers to register
more hardware queues, and allow them to map them to
virtual interfaces. When they stop a hardware queue
the corresponding AC software queues on the correct
interfaces will be stopped as well. Additionally,
there's an off-channel queue to solve that problem
and a per-interface after-DTIM beacon queue. This
allows drivers to manage software queues closer to
how the hardware works.

Currently, there's a limit of 16 hardware queues.
This may or may not be sufficient, we can adjust it
as needed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The queue mapping redesign that I'm planning to do
will break pure injection unless we handle monitor
interfaces explicitly. One possible option would
be to have the driver tell mac80211 about monitor
mode queues etc., but that would duplicate the API
since we already need to have queue assignments
handled per virtual interface.

So in order to solve this, have a virtual monitor
interface that is added whenever all active vifs
are monitors. We could also use the state of one
of the monitor interfaces, but managing that would
be complicated, so allocate separate state.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The AP netdev is really only active when beaconing, so
manage the carrier state accordingly. Also do that for
VLAN interfaces enslaved to a given AP interface.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>