Enable the sh_mobile_sdhi mfd driver on SH-Mobile ARM
processors. While at it, make CONFIG_TMIO_MMC depend on
CONFIG_MFD_SH_MOBILE_SDHI.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch adds cell->disable() calls to the tmio-mmc
probe() error handling and the remove() function.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch changes the tmio_mmc driver to wait 100ms
before checking the card detect status. This type of
delay is quite common among mmc drivers, it seems that
most hardware platforms need to give the hardware some
time to settle before checking card availabilty.

Hotplug is half-broken without this patch on the sh7724
Ecovec board. Hot insertion seems ok but eject is never
detected without this patch.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Enable MMC_CAP_XX support in the tmio_mmc driver if
pdata->capabilities is set.
Signed-off-by: NYusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

On SuperH platforms the SDHI controller does not produce any command IRQs after
a completed IO. This leads to card-detect interrupts staying disabled. Do not
disable card-detect interrupts on DATA IRQs.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This card reader doesn't advertise, however DMA works well.  Probably
windows SDHCI driver assumes that all readers support DMA and thus we see
that bug.
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Tested-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Norbert Preining <preining@logic.at>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

kunmap_atomic() accepts a pointer to any location in the page so we do not
need the subtraction and cast.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Wolfgang Muees <wolfgang.mues@auerswald.de>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We used to manage features and differences on a per-cpu basis.  As several
cpus share the same mci revision, this patch aggregates cpus that have the
same IP revision in one defined constant.  We use the
at91mci_is_mci1rev2xx() funtion name not to mess with newer Atmel sd/mmc
IP called "MCI2".  _rev2 naming could have been confusing...
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Wolfgang Muees <wolfgang.mues@auerswald.de>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

According to the datasheets AT91SAM9261 does not support SDIO interrupts,
and AT91SAM9260/9263 have an erratum requiring 4bit mode while using slot
B for the interrupt to work.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Wolfgang Muees <wolfgang.mues@auerswald.de>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch is setting some max_ variables for the IO elevator, so the
elevator will put requests for large data blocks to the driver.  This is
critical for

a) speed

and

b) wear leveling of the flash chip controller: Otherwise the controller
   will treat the SD card badly with millions of single 4 KByte write
   commands.  This will lead to a shorter life time for the SD cards.
Signed-off-by: NWolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert the read to use the DMA buffer as well.  The old code was doing
double-buffering DMA with the PDC; no way to make it work.  Replace it
with a single-PDC approach.  It also simplify things removing the need for
a pre_dma_read() function.

[nicolas.ferre@atmel.com coding style modifications]
Signed-off-by: NWolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The TX DMA buffer is allocated only once, because the
allocation/deallocation of the buffer for EACH chunk of data is
time-consuming and prone to memory fragmentation.

Using a coherent DMA buffer avoids extra data cache calls.

[nicolas.ferre@atmel.com: coding style modifications]
Signed-off-by: NWolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix two timeout errors, one for slow SDHC cards and one for slow users
while inserting SD cards.
Signed-off-by: NWolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixes two pointer errors, one which leads to memory overwrites if used
with large chunks of data.
Signed-off-by: NWolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If no platform_data was givin to the device it's going to use it's default
platform data struct which has all fields initialized to zero.  As a
result the driver is going to try to request gpio0 both as write protect
and card detect pin.  Which of course will fail and makes the driver
unusable

Previously to the introduction of no_wprotect and no_detect the behavior
was to assume that if no platform data was given there is no write protect
or card detect pin.  This patch restores that behavior.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Tested with an XO v1.5 from OLPC.
Signed-off-by: NNicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

sdhci_set_adma_desc() is using byte-writes to write data in a specified
order into memory.  Change to using __le16 for the two byte and __le32 for
the four byte cases and use the cpu_to_{le16,le32} to do the conversion
before writing.

This will reduce the size of the code and the number of writes as we no
longer need to chop the data up before writing.

As an example on ARM S3C64XX SoC, in little-endian configuration:

 000000d4 <sdhci_set_adma_desc>:
-      d8:	e1a0c423 	lsr	ip, r3, #8
-      dc:	e1a0ec21 	lsr	lr, r1, #24
-      e0:	e1a04821 	lsr	r4, r1, #16
-      e4:	e1a05421 	lsr	r5, r1, #8
-      e8:	e1a06442 	asr	r6, r2, #8
-      ec:	e5c0c001 	strb	ip, [r0, #1]
-      f0:	e5c0e007 	strb	lr, [r0, #7]
-      f4:	e5c04006 	strb	r4, [r0, #6]
-      f8:	e5c05005 	strb	r5, [r0, #5]
-      fc:	e5c01004 	strb	r1, [r0, #4]
-     100:	e5c06003 	strb	r6, [r0, #3]
-     104:	e5c02002 	strb	r2, [r0, #2]
-     108:	e5c03000 	strb	r3, [r0]
+      d4:	e5801004 	str	r1, [r0, #4]
+      d8:	e1c030b0 	strh	r3, [r0]
+      dc:	e1c020b2 	strh	r2, [r0, #2]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The code to write the ADMA descriptor into memory is repeated several
times throughout sdhci_adma_table_pre, and thus should be moved into a
common function.  This will also be useful if the patch to make the write
more efficient is accepted.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The hardcoded value doesn't really work for all cards.
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The host/Kconfig file is only included when MMC is selected.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The local sg variable is only used with BF54x code.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This prevents those without an Atmel chip having a line in kernel
configuration which says "Atmel SD/MMC Driver" without any option.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for 8bit MMC cards.  The controller data width is configurable
depending on the wires setting in the platform data structure.

MMC 8bit is tested on OMAPL137 and MMC 4bit is tested on OMAPL138 EVM.
Signed-off-by: NVipin Bhandari <vipin.bhandari@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Chaithrika U S <chaithrika@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch solves nasty problem original driver has.

Original goal of the ricoh_mmc was to disable this device because then,
mmc cards can be read using standard SDHCI controller, thus avoiding
writing of yet another driver.

However, the act of disablement, makes other pci functions that belong to
this controller (xD and memstick) shift up one level, thus pci core has
now wrong idea about these devices.

To fix this issue, this patch moves the driver into the pci quirk section,
thus it is executes before the pci is enumerated, and therefore solving
that issue, also same sequence of commands is performed on resume for same
reasons.

Also regardless of the above, this way is cleaner.  You still need to set
CONFIG_MMC_RICOH_MMC to enable this quirk
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Acked-by: NPhilip Langdale <philipl@overt.org>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Although the hardware supports a 4/8bit SD interface and the driver
unconditionally advertises all hardware caps to the MMC core, not all
datalines may actually be wired up.  This patch introduces another
field to au1xmmc platform data allowing platforms to disable certain
advanced host controller features.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
To: linux-mmc@vger.kernel.org
CC: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/460/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

DMA can only be done from physical addresses; move the "virt_to_phys"
source/destination buffer address translation from the dbdma queueing
functions (since the hardware can only DMA to/from physical addresses)
to their respective users.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove dbdma compat macros, move remaining users over to default
queueing functions and -flags.

(Queueing function signature has changed in order to give
 a build failure instead of silent functional changes due
 to the no longer implicitly specified DDMA_FLAGS_IE flag)
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This removes the custom DBG macro in favor of the in-kernel
dev_dbg() macro. Probably a leftover from a time when dev_dbg()
didn't yet exist. Also remove a printk() in favor of dev_err().
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

It is still possible to use the omap_hsmmc module
without the regulator framework.  Accordingly, ifdef
out regulator-specific functions.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

EMMC can have two voltage supplies, Vcc and VccQ
which are implemented in the code as consumer
supplies vmmc and vmmc_aux.

If the regulator that supplies vmmc_aux is shared
with other consumers, then sending it to sleep
will disrupt those consumers.  However, the
TWL4030-family regulators may have OFF remapped
to SLEEP, in which case 'regulator_disable()'
will put the regulator to sleep only when all
consumers are disabled - which is the desired
behaviour.

This patch adds a platform data field to allow
that option.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Stop using 'regulator_is_enabled()' and just pair enables
with disables so that the regulator reference counts can
work correctly.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Disable timeouts are in msecs not jiffies.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

An eMMC may be always powered on, so that the lowest
power saving state possible is sleeping. Add a field
to the platform data to indicate that.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch moves the setup code for GPIO's and Voltage
Regulators from the board file mmc-twl4030.c to the
driver omap_hsmmc.c.  PBIAS and other system control
configuration remains in the board file.

Moving GPIO code to the driver makes the board initialisation
code independent of when GPIO's are defined.  That makes the
board initialisation now entirely independent of its original
twl4030 roots.

Moving Voltage Regulator code to the driver allows for further
development of regulator support in the core MMC code.  It also
permits the MMC core to be compiled as a module, because the
board code no longer calls MMC core functions.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

In the U300 some hardware bug makes the status flag not come up
signalling a successful write (or anything else, like an error, for
that matter) on write requests. This little quirk makes the writes
work on U300.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch abstracts out the CNF area code from tmio_mmc which
is not present in all hardware that can use this driver. This
is required so that we can support non-toshiba based hardware.

ASIC3 support by Philipp Zabel
Signed-off-by: NIan Molton <ian@mnementh.co.uk>
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add support for the Secure Digital Host Controller Interface found on the
"Hollywood" chipset of the Nintendo Wii video game console.
Signed-off-by: NAlbert Herranz <albert_herranz@yahoo.es>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch breaks down sdhci-of into a core portion and a eSDHC portion,
clearing the path to easily support additional hardware using the same OF
driver.
Signed-off-by: NAlbert Herranz <albert_herranz@yahoo.es>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch renames sdhci-of.c to sdhci-of-core.c before reorganizing the
driver to support additional hardware.

The driver is still built as sdhci-of despite the rename of the file.  No
functional change.
Signed-off-by: NAlbert Herranz <albert_herranz@yahoo.es>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>