It's unlikely that this is really needed on any single-slot systems
where we disable card detects until the end of probe, but it still
seems safer to check to make sure that a slot has been initted before
we try to dereference it to find the SDIO interrupt mask.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We really don't want to get a card detect interrupt during probe time
since it can confuse things.  Let's disable the card detect interrupt
until we're in a really good place: the end of probe.  Let's also
simply avoid enabling the card detect interrupt if it's not used.

It appears that (at least on rk3288) when vqmmc is turned on it can
cause a bogus "card detect" interrupt.  That meant that we were
getting a predictable card detect interrupt while we were in
mmc_add_host().  On the version of the kernel I'm working with at
least (3.14), this is not a great time to get a card detect interrupt
since I think that we don't grab all the needed locks in
mmc_add_host() and children.  I put stack dumps in dw_mci_setup_bus()
and found that I could see two distinct stack crawls that looked like:

Caller one:
* dw_mci_setup_bus
* dw_mci_set_ios
* mmc_power_up
* mmc_start_host
* mmc_add_host

Caller two:
* dw_mci_setup_bus
* dw_mci_set_ios
* mmc_set_chip_select
* mmc_go_idle
* mmc_rescan
* process_one_work
* worker_thread
* kthread
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We've seen problems on some WiFi modules where we seem to send a CMD53
(which requires the data lines) while the module is asserting busy.
We shouldn't do that.

The Designware Databook says that before issuing a new data transfer
command we should check for busy, so that's what we'll do.

We'll leverage the existing dw_mmc knowledge about whether it should
wait for the previous command to finish to know whether we should
check for busy before sending the command.  This means we won't end up
incorrectly waiting for things like CMD52 (SDIO) or CMD13 (SD) which
don't use the data line.

Note that this also has the advantage of making sure that we don't
change the clock while the card is busy, too.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We should give dw_mmc a good reset after we apply power.  On some
boards vqmmc may actually be connected to the IP block in the SoC so
it's good to reset after power comes in.

Without this we sometimes see failures enumerating cards on rk3288.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

It appears that we can confuse things if we try to turn on the MMC
clock when the power is off.  Adjust is so that we turn the clock on
(using dw_mci_setup_bus) after power is all the way on and we turn the
clock off before the power goes off.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The STOP command can terminate a data transfer between a memory card and
mmc controller.

As show in Synopsys DesignWare Cores Mobile Storage Host Databook:
Data timeout and Data end-bit error will terminate further data transfer
by mmc controller. So we should not send abort command to terminate a
data transfer again if we got DRTO and EBE interrupt.

After this patch, all mmc_test cases can pass on RK3288-Pink2 board.
Signed-off-by: NAddy Ke <addy.ke@rock-chips.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Implements HS400 mode support for exynos host driver.
This also include some updates as new mode is added.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NAlim Akhtar <alim.akhtar@samsung.com>
[Alim: addressed review comments]
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If we power up vqmmc in MMC_POWER_ON then we end up turning it on
before mmc_power_up() sets the signal voltage.  That's not so great
since we might be powering it up at the wrong voltage.

Note that this is how Yuvaraj originally coded things up in
<https://patchwork.kernel.org/patch/4401231/> but he changed it on my
suggestion.  Apparently I was wrong.
Reported-by: NAlexandru M Stan <amstan@chromium.org>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Instead of having a local hack taking care of sending the tuning
command and as well to verify the response pattern, let's convert to
the common mmc_send_tuning() API.

This change affects the Exynos variant, since it's the only one which
support the dw_mmc's ->execute_tuning() callback.

It's seems like dw_mmc internal logic expects failed data transfers to
be ended using a stop command. Let the tuning requests also fall into
this category, since there are data transfer involved.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com>
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>

This patch remove unnecessary 'out of memory' message on dw mmc driver.
Signed-off-by: NBeomho Seo <beomho.seo@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Even though 1MB is reserved for descriptor table in IDMAC,
the dw_mmc host driver is allowed to receive only maximum
128KB block length in one request. This is caused by setting
improper max_blk_count. It needs to be e adjusted so that
descriptor table is used fully. It is found that the performance
is improved with the increased the max_blk_count.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We're running into cases where our enabling of the SDIO interrupt in
dw_mmc doesn't actually take effect.  Specifically, adding patch like
this:

 +++ b/drivers/mmc/host/dw_mmc.c
 @@ -1076,6 +1076,9 @@ static void dw_mci_enable_sdio_irq(struct mmc_host *mmc, int enb)

      mci_writel(host, INTMASK,
           (int_mask | SDMMC_INT_SDIO(slot->id)));
 +    int_mask = mci_readl(host, INTMASK);
 +    if (!(int_mask & SDMMC_INT_SDIO(slot->id)))
 +      dev_err(&mmc->class_dev, "failed to enable sdio irq\n");
    } else {

...actually triggers the error message.  That's because the
dw_mci_enable_sdio_irq() unsafely does a read-modify-write of the
INTMASK register.

We can't just use the standard host->lock since that lock is not irq
safe and mmc_signal_sdio_irq() (called from interrupt context) calls
dw_mci_enable_sdio_irq().  Add a new irq-safe lock to protect INTMASK.

An alternate solution to this is to punt mmc_signal_sdio_irq() to the
tasklet and then protect INTMASK modifications by the standard host
lock.  This seemed like a bit more of a high-latency change.
Reported-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In the patch (9623b5b9 mmc: dw_mmc: Disable low power mode if SDIO
interrupts are used) I added code that disabled the low power mode of
dw_mmc when SDIO interrupts are used.  That code worked but always
felt a little hacky because we ended up disabling low power as a side
effect of the first enable_sdio_irq() call.  That wouldn't be so bad
except that disabling low power involves a complicated process of
writing to the CMD/CMDARG registers and that extra process makes it
difficult to cleanly the read-modify-write race in
dw_mci_enable_sdio_irq() (see future patch in the series).

Change the code to take advantage of the init_card() callback of the
mmc core to do this right at bootup.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Commit f1d2736c (mmc: dw_mmc: control card read threshold) added
dw_mci_ctrl_rd_thld() with an unconditional write to the CDTHRCTL
register at offset 0x100. However before version 240a, the FIFO region
started at 0x100, so the write messes with the FIFO and completely
breaks the driver.

If the version id < 240A, return early from dw_mci_ctl_rd_thld() so as
not to hit this problem.

Fixes: f1d2736c (mmc: dw_mmc: control card read threshold)
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.13+
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The bit of sdio interrupt is 16 in designware implementation,
but it is 24 on Rockchip SoCs.This patch add sdio_id0 for the
number of slot0 in the SDIO interrupt registers.
Signed-off-by: NAddy Ke <addy.ke@rock-chips.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Synopsys DW_MMC IP core supports Internal DMA Controller with 64-bit address mode from IP version 2.70a onwards.
Updated the driver to support IDMAC 64-bit addressing mode.
Signed-off-by: NPrabu Thangamuthu <prabu.t@synopsys.com>
Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The dw_mmc driver had a bunch of code that ran whenever a card was
ejected and inserted.  However, this code was old and crufty and
should be removed.  Some evidence that it's really not needed:

1. Is is supposed to be legal to use 'cd-gpio' on dw_mmc instead of
   using the built-in card detect mechanism.  The 'cd-gpio' code
   doesn't run any of the crufty old code but yet still works.

2. While looking at this, I realized that my old change (369ac861 mmc:
   dw_mmc: don't queue up a card detect at slot startup) actually
   castrated the old code a little bit already and nobody noticed.
   Specifically "last_detect_state" was left as 0 at bootup.  That
   means that on the first card removal none of the crufty code ran.

3. I can run "while true; do dd if=/dev/mmcblk1 of=/dev/null; done"
   while ejecting and inserting an SD Card and the world doesn't
   explode.

If some of the crufty old code is actually needed, we should justify
it and also put it in some place where it will be run even with
"cd-gpio".

Note that in my case I'm using the "cd-gpio" mechanism but for various
reasons the hardware triggers a dw_mmc "card detect" at bootup.  That
was actually causing a real bug.  The card detect workqueue was
running while the system was trying to enumerate the card.  The
"present != slot->last_detect_state" triggered and we were doing all
kinds of crazy stuff and messing up enumeration.  The new mechanism of
just asking the core to check the card is much safer and then the
bogus interrupt doesn't hurt.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: Nalim.akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In (28f92b5 mmc: core: Try other signal levels during power up) we can
see that there are times when it's valid to try several signal
voltages.  Don't print an ugly error in the logs when that happens.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We've already got a reset of DMA after it's done.  Add one before we
start DMA too.  This fixes a data corruption on Rockchip SoCs which
will get bad data when doing a DMA transfer after doing a PIO transfer.

We tested this on an Exynos 5800 with HS200 and didn't notice any
difference in sequential read throughput.
Signed-off-by: NSonny Rao <sonnyrao@chromium.org>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The same tuning block exists in the dw_mmc h.c and sdhci-msm.c
files. Move these into mmc.c so that they can be shared across
drivers.
Reported-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

dw_mci_of_find_slot_node() is only used in dw_mci_of_get_slot_quirks()
if CONFIG_OF is defined, thus there is no need to have a !CONFIG_OF
version of it. Fixes the following compile warning with !CONFIG_OF:

  CC [M]  drivers/mmc/host/dw_mmc.o
drivers/mmc/host/dw_mmc.c:2223:28: warning: ‘dw_mci_of_find_slot_node’ defined but not used [-Wunused-function]
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

It's possible that mmc_of_parse() could return errors (possibly in
some future version it might return -EPROBE_DEFER even).  Let's pass
those errors back.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

For UHS cards we need the ability to switch voltages from 3.3V to
1.8V.  Add support to the dw_mmc driver to handle this.  Note that
dw_mmc needs a little bit of extra code since the interface needs a
special bit programmed to the CMD register while CMD11 is progressing.
This means adding a few extra states to the state machine to track.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch makes use of mmc_regulator_get_supply() to handle
the vmmc and vqmmc regulators.Also it moves the code handling
the these regulators to dw_mci_set_ios().It turned on the vmmc
and vqmmc during MMC_POWER_UP and MMC_POWER_ON,and turned off
during MMC_POWER_OFF.
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If we happened to get a data error at just the wrong time the dw_mmc
driver could get into a state where it would never complete its
request.  That would leave the caller just hanging there.

We fix this two ways and both of the two fixes on their own appear to
fix the problems we've seen:

1. Fix a race in the tasklet where the interrupt setting the data
   error happens _just after_ we check for it, then we get a
   EVENT_XFER_COMPLETE.  We fix this by repeating a bit of code.
2. Fix it so that if we detect that we've got an error in the "data
   busy" state and we're not going to do anything else we end the
   request and unblock anyone waiting.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@gmail.com>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Slot quirks "disable-wp" is deprecated.
Instead, use the host quirk "disable-wp".
(Because the slot-node is removed in dt-file.)
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NSachin Kamat <sachin.kamat@samsung.com>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch changes the fifo reset code to follow the reset procedure
outlined in the documentation of Synopsys Mobile storage host databook.
Signed-off-by: NSonny Rao <sonnyrao@chromium.org>
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
[sonnyrao: fix compile for !CONFIG_MMC_DW_IDMAC case]
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Data errors are completely expected during tuning.  Printing them out
is confusing people looking at the kernel logs.  They see things like:

 [    3.613296] dwmmc_exynos 12200000.dwmmc0: data error, status 0x00000088

...and they think something is wrong with their hardware.

Remove the printouts.  We'll leave it up to a higher level to report
about errors.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Restore the card-present checking point.

(The following part was removed from commit bf626e55 ("mmc: dw_mmc:
use slot-gpio to handle cd pin")
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

If mmc_of_parse() is used, dw_mci_of_get_cd_gpio/wp_gpio didn't need.
Already implemented into mmc_of_parse().
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Remove unnecessary function.  This function didn't re-use anywhere.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Fixed an indentation block.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Since using the device-tree, didn't use the callback pointer.
So removed the unused callback pointer.
When the set_power callback is used, it should be added in future.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

It's right to check immediately whether host->bus_hz is assigned or not.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

mmc_of_parse() have been already parsed the general capability.
Didn't need to use the local parser.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Replaced UHS_DDR50 with MMC_DDR52. And MMC_CAP_UHS_DDR50
is removed because of non-implementation of UHS signaling.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Tejun Heo has made WQ_NON_REENTRANT useless in the dbf2576e
("workqueue: make all workqueues non-reentrant"). So remove its
usages and definition.

This patch doesn't introduce any behavior changes.

tj: minor description updates.
Signed-off-by: NZhangZhen <zhenzhang.zhang@huawei.com>
Sigend-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NJames Chapman <jchapman@katalix.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>

If mrq->sbc is not NULL but data->stop happens to be NULL,
it will lead to NULL pointer dereferencing. Avoid this by
having a NULL check for data->stop.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NChris Ball <chris@printf.net>

bf626e55 ("mmc: dw_mmc: use slot-gpio to handle cd pin") caused
CDETECT to be ignored, since negated return value of mmc_gpio_get_cd(mmc)
can not be checked by IS_ERR_VALUE.

Also, add spin_lock_bh(&host->lock) for atomic access to
DW_MMC_CARD_PRESENT, otherwise sd detect may occasionally fail.
Signed-off-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Reported-by: NKevin Hilman <khilman@linaro.org>
Reviewed-by: NSachin Kamat <sachin.kamat@linaro.org>
Tested-by: NSachin Kamat <sachin.kamat@linaro.org>
Tested-by: NKevin Hilman <khilman@linaro.org>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NChris Ball <chris@printf.net>

Suggested by Jaehoon: Use slot-gpio to handle cd-gpio
Add function dw_mci_of_get_cd_gpio to check "cd-gpios" from dts.
mmc_gpio_request_cd and mmc_gpio_get_cd are used to handle cd pin
Signed-off-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NChris Ball <chris@printf.net>