These were left in during removal of touch pressure reports but not
needed now.
Signed-off-by: NChris Bagwell <chris@cnpbagwell.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

CONFIG_PM is defined when CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is defined,
however suspend and resume methods are only valid in the context of
CONFIG_PM_SLEEP. If only CONFIG_PM_RUNTIME is defined we get the following
warning (courtesy of Geerts randconfig builds):

	lm8323.c: warning: 'lm8323_resume' defined but not used
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

CONFIG_PM is defined when CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is defined,
however suspend and resume methods are only valid in the context of
CONFIG_PM_SLEEP. If only CONFIG_PM_RUNTIME is defined we get the following
warning (courtesy of Geerts randconfig builds):

	ad7879-i2c.c: warning: 'ad7879_i2c_resume' defined but not used
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

CONFIG_PM is defined when CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is defined,
however suspend and resume methods are only valid in context of
CONFIG_PM_SLEEP. If only CONFIG_PM_RUNTIME is defined we get the following
warning (courtesy of Geerts randconfig builds):

	synaptics_i2c.c: warning: 'synaptics_i2c_resume' defined but not used
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Sometimes GCC is not smart enough to recognize that x, y and z are
always used properly initialized in mma8450_poll(). Let's rearrange
the code a bit to help GCC.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Sysfs attribute show methods are always passed a buffer of length
PAGE_SIZE.  To keep from overwriting this buffer and causing havoc, use
snprintf() to guarantee we never write more than the buffer can hold.

In addition, at least for my touchscreen, the number and size of objects
was far too big to fit in a single 4K page.  Therefore, this patch also
trims some redundant framing text to leave more room for actual data.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NNick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Reviewed-by: NEduard Hasenleithner <eduard@hasenleithner.at>
Tested-by: NEduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Cintiq 21ux2 has two sets of four LEDs on right and left side of
the tablet, respectively.
Reviewed-by: NEduard Hasenleithner <eduard@hasenleithner.at>
Tested-by: NEduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The LED also indicates the status of the tablet. Don't turn it off.
Reviewed-by: NEduard Hasenleithner <eduard@hasenleithner.at>
Tested-by: NEduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The LED luminance level is normally lower when no button is pressed.
Reviewed-by: NEduard Hasenleithner <eduard@hasenleithner.at>
Tested-by: NEduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This patch adds the TSC-40 serial touchscreen driver and should be
compatible with TSC-10 and TSC-25.

The driver was written by Linutronix on behalf of Bachmann electronic GmbH.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NChristian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This patch clarifies a few bits of documentation in the header file
for the adxl34x driver.
Signed-off-by: NMichael Tandy <lkml@mkt.me.uk>
Acked-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Use the of_property_read_u32() helper function to retrieve u32 values
from the device tree. Also do not pass the len parameter to
of_get_property if it isn't checked afterwards.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Since touchscreen driver does not handle any events to be sent to the
device we can close serio port first and then unregister the input device.
Tested-by: NJohn Sung <penmount.touch@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Instead of having one large switch based on product ID use pointer to
function actually doing protocol decoding.
Tested-by: NJohn Sung <penmount.touch@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Add multi touch support for PenMount 6250 touch controller.
Signed-off-by: NJohn Sung <penmount.touch@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Add dual touch support for PenMount 3000 touch controller.
Signed-off-by: NJohn Sung <penmount.touch@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Add support for PenMount 6000 touch controller.
Signed-off-by: NJohn Sung <penmount.touch@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The MSB and LSB of the XY axis value are switched according to the PenMount 9000 protocol. The driver name is also changed from penmountlpc, since it is not for LPC interface at all.
Signed-off-by: NJohn Sung <penmount.touch@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This essentially reverts commit f81bc788.

With recent work on elantech driver, I believe we now have complete support
for all elantech touchpads. So remove this hack.
Signed-off-by: NJJ Ding <jj_ding@emc.com.tw>
Reviewed-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

V2 hardware has many variants. This patch adddresses two issues:

 - some model also has debounce packets, but with a different signature
   than v3. Now we just check debounce for all v2 hardware.

 - due to different scanning methods the hardware uses, x and y ranges have
   to be calculated differently. And for some specific versions, we can just
   see them as custom-made, so set {x, y} the same values as Windows driver
   does.
Signed-off-by: NJJ Ding <jj_ding@emc.com.tw>
Tested-by: NRichard Schütz <r.schtz@t-online.de>
Reviewed-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

v4 hardware is a true multitouch capable touchpad (up to 5 fingers).
The packet format is quite complex, please see protocol document for
reference.
Signed-off-by: NJJ Ding <jj_ding@emc.com.tw>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

v3 hardware's packet format is almost identical to v2 (one/three finger touch),
except when sensing two finger touch, the hardware sends 12 bytes of data.
Signed-off-by: NJJ Ding <jj_ding@emc.com.tw>
Acked-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Group property setting code into elantech_set_properties.
Signed-off-by: NJJ Ding <jj_ding@emc.com.tw>
Acked-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

For v2 hardware, there is no real parity check, but we can still check
some constant bits for data integrity.

Also rename elantech_check_parity_v1 to elantech_packet_check_v1 to make
these packet checking function names consistent.
Signed-off-by: NJJ Ding <jj_ding@emc.com.tw>
Acked-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Don't try to be too clever and remove ETP_EDGE_FUZZ_V2. X, Y ranges
should be just the raw resolution of the device. Otherwise, they can
cause underflow on the Y axis.
Suggested-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NJJ Ding <jj_ding@emc.com.tw>
Acked-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

With newer hardware, the touchpad provides range info.
Let's use it.
Signed-off-by: NJJ Ding <jj_ding@emc.com.tw>
Acked-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

For two finger touches the coordinate of each finger gets reported
separately but with reduced resolution.

With this change, we now have the same range for ST and MT data and
scale MT data because it has lower resolution to match ST.
Suggested-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NJJ Ding <jj_ding@emc.com.tw>
Acked-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

x, y values are actually 12-bit long. Also update protocol document to
reflect the change.
Signed-off-by: NJJ Ding <jj_ding@emc.com.tw>
Acked-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Fix warning from Geert's build summary emails by changing "if" to
"ifdef". Thsi should fix the following:

drivers/input/misc/twl6040-vibra.c:231:5: warning: "CONFIG_PM_SLEEP" is not defined

Builds cleanly with CONFIG_PM_SLEEP enabled or disabled.
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Take spinlock when entering ISR and timer routine to ensure that we do not
race while enabling/disabling FIFO interrupts.

Also we do not need to take teh spinlock in tegra_kbc_startremove() since
interrupt is completely disabled.
Tested-by: NRakesh Iyer <riyer@nvidia.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

For wakeup to be reliable, kbc needs to be in interrupt mode before suspend.
Created common routine to control the FIFO interrupt.
Added synchronization to ensure orderly suspend.
Signed-off-by: NRakesh Iyer <riyer@nvidia.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

WARNING: drivers/input/keyboard/built-in.o(.text+0xb55b): Section mismatch in reference from the function tc3589x_keypad_open() to the function .devinit.text:tc3589x_keypad_init_key_hardware()
The function tc3589x_keypad_open() references
the function __devinit tc3589x_keypad_init_key_hardware().
This is often because tc3589x_keypad_open lacks a __devinit
annotation or the annotation of tc3589x_keypad_init_key_hardware is wrong.
Signed-off-by: NHarvey Yang <harvey.huawei.yang@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This flag is a NOOP and can be removed now.
Signed-off-by: NYong Zhang <yong.zhang0@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This commit enables control of the LEDs and OLED displays found on the
Wacom Intuos4 M, L, and XL. For this purpose, a new "wacom_led" attribute
group is added to the sysfs entry of the USB device.

This "wacom_led" group only shows up when the correct device (M, L, or XL)
is detected. The attributes are described in
 Documentation/ABI/testing/sysfs-wacom
Signed-off-by: NEduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ARM: mach-shmobile: sh7372 LCDC1 suspend fix V2 (incremental)
  OMAP: omap_device: only override _noirq methods, not normal suspend/resume
  PM / Runtime: Correct documentation of pm_runtime_irq_safe()
  ARM: mach-shmobile: sh7372 LCDC1 suspend fix
  sh-sci / PM: Use power.irq_safe
  PM: Use spinlock instead of mutex in clock management functions

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: sbp2: fix panic after rmmod with slow targets

This patch updates the recently submitted
"Associate the HDMI clock together with LCDC1 on sh7372"
to V2 with the following change:
 - Use lcdc1_device on AP4EVB to build properly.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>