Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 21 6月, 2017 2 次提交
  3. 16 6月, 2017 2 次提交
    • J
      networking: make skb_push & __skb_push return void pointers · d58ff351
      由 Johannes Berg 提交于 
      It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.

Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:

    @@
    expression SKB, LEN;
    typedef u8;
    identifier fn = { skb_push, __skb_push, skb_push_rcsum };
    @@
    - *(fn(SKB, LEN))
    + *(u8 *)fn(SKB, LEN)

    @@
    expression E, SKB, LEN;
    identifier fn = { skb_push, __skb_push, skb_push_rcsum };
    type T;
    @@
    - E = ((T *)(fn(SKB, LEN)))
    + E = fn(SKB, LEN)

    @@
    expression SKB, LEN;
    identifier fn = { skb_push, __skb_push, skb_push_rcsum };
    @@
    - fn(SKB, LEN)[0]
    + *(u8 *)fn(SKB, LEN)

Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d58ff351
    • J
      networking: introduce and use skb_put_data() · 59ae1d12
      由 Johannes Berg 提交于 
      A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.

An spatch similar to the one for skb_put_zero() converts many
of the places using it:

    @@
    identifier p, p2;
    expression len, skb, data;
    type t, t2;
    @@
    (
    -p = skb_put(skb, len);
    +p = skb_put_data(skb, data, len);
    |
    -p = (t)skb_put(skb, len);
    +p = skb_put_data(skb, data, len);
    )
    (
    p2 = (t2)p;
    -memcpy(p2, data, len);
    |
    -memcpy(p, data, len);
    )

    @@
    type t, t2;
    identifier p, p2;
    expression skb, data;
    @@
    t *p;
    ...
    (
    -p = skb_put(skb, sizeof(t));
    +p = skb_put_data(skb, data, sizeof(t));
    |
    -p = (t *)skb_put(skb, sizeof(t));
    +p = skb_put_data(skb, data, sizeof(t));
    )
    (
    p2 = (t2)p;
    -memcpy(p2, data, sizeof(*p));
    |
    -memcpy(p, data, sizeof(*p));
    )

    @@
    expression skb, len, data;
    @@
    -memcpy(skb_put(skb, len), data, len);
    +skb_put_data(skb, data, len);

(again, manually post-processed to retain some comments)
Reviewed-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      59ae1d12
  5. 08 6月, 2017 1 次提交
  7. 07 6月, 2017 9 次提交
  9. 12 5月, 2017 4 次提交
    • U
      s390/qeth: add missing hash table initializations · ebccc739
      由 Ursula Braun 提交于 
      commit 5f78e29c ("qeth: optimize IP handling in rx_mode callback")
added new hash tables, but missed to initialize them.

Fixes: 5f78e29c ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ebccc739
    • J
      s390/qeth: avoid null pointer dereference on OSN · 25e2c341
      由 Julian Wiedmann 提交于 
      Access card->dev only after checking whether's its valid.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      25e2c341
    • J
      s390/qeth: unbreak OSM and OSN support · 2d2ebb3e
      由 Julian Wiedmann 提交于 
      commit b4d72c08 ("qeth: bridgeport support - basic control")
broke the support for OSM and OSN devices as follows:

As OSM and OSN are L2 only, qeth_core_probe_device() does an early
setup by loading the l2 discipline and calling qeth_l2_probe_device().
In this context, adding the l2-specific bridgeport sysfs attributes
via qeth_l2_create_device_attributes() hits a BUG_ON in fs/sysfs/group.c,
since the basic sysfs infrastructure for the device hasn't been
established yet.

Note that OSN actually has its own unique sysfs attributes
(qeth_osn_devtype), so the additional attributes shouldn't be created
at all.
For OSM, add a new qeth_l2_devtype that contains all the common
and l2-specific sysfs attributes.
When qeth_core_probe_device() does early setup for OSM or OSN, assign
the corresponding devtype so that the ccwgroup probe code creates the
full set of sysfs attributes.
This allows us to skip qeth_l2_create_device_attributes() in case
of an early setup.

Any device that can't do early setup will initially have only the
generic sysfs attributes, and when it's probed later
qeth_l2_probe_device() adds the l2-specific attributes.

If an early-setup device is removed (by calling ccwgroup_ungroup()),
device_unregister() will - using the devtype - delete the
l2-specific attributes before qeth_l2_remove_device() is called.
So make sure to not remove them twice.

What complicates the issue is that qeth_l2_probe_device() and
qeth_l2_remove_device() is also called on a device when its
layer2 attribute changes (ie. its layer mode is switched).
For early-setup devices this wouldn't work properly - we wouldn't
remove the l2-specific attributes when switching to L3.
But switching the layer mode doesn't actually make any sense;
we already decided that the device can only operate in L2!
So just refuse to switch the layer mode on such devices. Note that
OSN doesn't have a layer2 attribute, so we only need to special-case
OSM.

Based on an initial patch by Ursula Braun.

Fixes: b4d72c08 ("qeth: bridgeport support - basic control")
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      2d2ebb3e
    • U
      s390/qeth: handle sysfs error during initialization · 9111e788
      由 Ursula Braun 提交于 
      When setting up the device from within the layer discipline's
probe routine, creating the layer-specific sysfs attributes can fail.
Report this error back to the caller, and handle it by
releasing the layer discipline.
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
[jwi: updated commit msg, moved an OSN change to a subsequent patch]
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      9111e788
  11. 12 4月, 2017 10 次提交
  13. 07 4月, 2017 7 次提交
  15. 25 3月, 2017 2 次提交
    • J
      s390/qeth: no ETH header for outbound AF_IUCV · acd9776b
      由 Julian Wiedmann 提交于 
      With AF_IUCV traffic, the skb passed to hard_start_xmit() has a 14 byte
slot at skb->data, intended for an ETH header. qeth_l3_fill_af_iucv_hdr()
fills this ETH header... and then immediately moves it to the
skb's headroom, where it disappears and is never seen again.

But it's still possible for us to return NETDEV_TX_BUSY after the skb has
been modified. Since we didn't get a private copy of the skb, the next
time the skb is delivered to hard_start_xmit() it no longer has the
expected layout (we moved the ETH header to the headroom, so skb->data
now starts at the IUCV_TRANS header). So when qeth_l3_fill_af_iucv_hdr()
does another round of rebuilding, the resulting qeth header ends up
all wrong. On transmission, the buffer is then rejected by
the HiperSockets device with SBALF15 = x'04'.
When this error is passed back to af_iucv as TX_NOTIFY_UNREACHABLE, it
tears down the offending socket.

As the ETH header for AF_IUCV serves no purpose, just align the code to
what we do for IP traffic on L3 HiperSockets: keep the ETH header at
skb->data, and pass down data_offset = ETH_HLEN to qeth_fill_buffer().
When mapping the payload into the SBAL elements, the ETH header is then
stripped off. This avoids the skb manipulations in
qeth_l3_fill_af_iucv_hdr(), and any buffer re-entering hard_start_xmit()
after NETDEV_TX_BUSY is now processed properly.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      acd9776b
    • J
      s390/qeth: size calculation outbound buffers · 7d969d2e
      由 Julian Wiedmann 提交于 
      Depending on the device type, hard_start_xmit() builds different output
buffer formats. For instance with HiperSockets, on both L2 and L3 we
strip the ETH header from the skb - L3 doesn't need it, and L2 carries
it in the buffer's header element.
For this, we pass data_offset = ETH_HLEN all the way down to
__qeth_fill_buffer(), where skb->data is then adjusted accordingly.
But the initial size calculation still considers the *full* skb length
(including the ETH header). So qeth_get_elements_no() can erroneously
reject a skb as too big, even though it would actually fit into an
output buffer once the ETH header has been trimmed off later.

Fix this by passing an additional offset to qeth_get_elements_no(),
that indicates where in the skb the on-wire data actually begins.
Since the current code uses data_offset=-1 for some special handling
on OSA, we need to clamp data_offset to 0...

On HiperSockets this helps when sending ~MTU-size skbs with weird page
alignment. No change for OSA or AF_IUCV.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7d969d2e
  17. 12 1月, 2017 3 次提交